MANUAL
D3907 / 19.12.2018
MAINTENANCE
Keep the cooker hood clean. Wipe outer surfaces regularly
with water containing a small amount of a mild detergent.
Clean o any grease stains immediately. Do not use abrasive
or corrosive detergents or tools.
Keep the grease filter clean to ensure an adequate extract air
flow. The grease filter must be washed with warm water and
detergent at least 1-2 times a month.
Light
The cooker hood has a long-lasting LED lighting module. If
the light is not working, contact a servicing company.
Removing and mounting the grease filter
Removing the filter Mounting the filter
1 2 3 4
5
min. 426mm /
650mm
50mm
20mm
• Pull the locking device of the grease filter towards the
front edge of the cooker hood while pulling the grease
filter downwards until it comes o.
• Wash the grease filter and leave to dry.
• Mount the grease filter back in place. Push the front
edge of the filter into the pins on the cooker hood, and
click the rear edge in place.
NOTE! Ensure that the locking device points
downwards.
PLEASE NOTE!
The minimum distance of the bottom edge of the hood
to an electric cooker is 426 mm and to a gas cooker
650 mm.
PLEASE NOTE!
• The cooker hood must not be connected to a flue that
is used for removing combustion gases (e.g. from a
wood- or gas-burning fireplace, cooker, or stove).
• Regulations on leading extraction air outdoors must
be observed.
PLEASE NOTE!
• The power outlet used for the cooker hood must
be easy to access.
• Only the power adapter that is delivered with the
unit and corresponds to the voltage specified in
the type plate of the unit must be used to connect
the cooker hood into the mains.
Figure 5.
Location of the L strip when the lowest hood mounting
height is used.
INSTALLATION
In the example, the bottom of the sides and the rear of the
hood are level with the bottom of the top cabinets (see
figures 1-2). In this case, a specially made cover panel is
needed to hide the hood. The height of the cover panel is
roughly 210 mm.
The hood can also be installed higher, even so that it touches
the frame of the spice cabinet. In this case, rear corners need
to be sawn o from the spice cabinet frame (see figure 3). In
this mounting method, the height of the hood cover panel is
100 mm.
When the lowest possible mounting height is used, the
bottom edge of the sliding glass, when pushed inside the
hood, is level with the bottom of the top cabinet frames
(see figure 4). The L strip is mounted on the wall as shown
in figure 5. In this mounting method, the height of the hood
cover panel is roughly 248 mm.
Figure 1.
Remove the spice cabinet. Mount the L strip on the wall so
that it is level.
The L strip fully covers the gap between the hood and the
wall and also makes it easier to balance the hood in place
during mounting.
If the top cabinet frames are less than 305 mm deep, the
longer edge of the L strip is mounted on the wall. The
perforations on the lower surface of the L strip can be
covered using white plastic studs.
Figure 2.
Place the hood on top of the L strip so that it is level and
fasten the hood on the top cabinet frames with four screws.
It is vital that the hood is both vertically and horizontally
level. The front panel of the hood must be at the same depth
as the outer surface of the top cabinet doors.
Figure 3.
If the highest possible hood mounting height is used, saw o
diagonal pieces measuring at least 20x50 mm from the spice
cabinet frame.
Figure 4.
The hood when the lowest possible mounting height is used.
Vallox Oy | Myllykyläntie 9-11 | 32200 LOIMAA | FINLAND | www.vallox.com
Customer Service +358 10 7732 200 | Aftersales +358 10 7732 270
