Vallox X-Line KTX User manual

Manual
Document
D11204
Valid from
28.02.2020
Updated
28.04.2023
MANUAL
Model
Vallox X-Line KTX
Type
27983-3
The Vallox X-Line KTX cooker hood is designed to be used above the cooker
top or as a general extraction valve in the kitchen.

2
MANUAL
VENTILATION CONTROL
For buildings with a centralized ventilation system.
The air flow of the Vallox X-Line KTX cooker hood is
adjusted with an extract valve that is installed on the
hood at setup. The valve must be adjusted so that it
meets the requirements set for a smoke limiter.
USING THE UNIT
Cooker hood light switch
Rocker switch operation
• Right side down, light on.
• Left side down, light o.
Front panel
MAINTENANCE
Keep the cooker hood clean. Wipe outer surfaces
regularly with water containing a small amount of a mild
detergent. Clean o any grease stains immediately. Do
not use abrasive or corrosive detergents or tools.
Keep the grease filter clean to ensure an adequate
extract air flow. The grease filter must be washed with
warm water and detergent by hand or in a dishwasher
at least 1-2 times a month.
Replacing the lamp
• Remove the protective glass of the lamp by moving it
to the left (Figure 3).
• Remove the lamp by pulling it to the left (figure 4).
• Lamp type: G23 LED.
Removing and mounting the grease
filter
• Open the quick connectors of the bottom plate of
the cooker hood by turning (Figure 1).
• Turn the bottom plate down.
• Remove the grease filter from its holder (Figure 2).
1 2
Light switch
WARNING
A G23 PL lamp will cause damage!
WARNING
The unit is not intended for use
by children under 8 or by persons
with reduced sensory, physical or
mental capabilities, or whose lack
of knowledge and experience do
not ensure safe operation of the
unit. Such persons can use the unit
under supervision, or by following
the instructions of someone who is
responsible for their safety. Do not let
children play with the unit or to clean or
maintain it without supervision.
WARNING
If the ventilation of the apartment
is turned o, the entry of fresh
replacement air into the apartment
and the extraction of used air from the
apartment are prevented. Impurities,
such as carbon dioxide, humidity,
smells, formaldehyde, dust, and radon,
which come from people, structures,
and the soil will quickly contaminate the
room air and are harmful to the health
of people. Excessive humidity may
damage the structures of the building
and result in mould and fungal growth.
For this reason, building regulations
require that ventilation be turned on
at all times and that its eciency is
adjusted based on the needs of the
user.
CAUTION
• Neglecting the cleaning of the
grease filter can cause a fire
hazard.
• The outer surfaces of the hood can
become hot when the cooker or
the oven is turned on.
• Flaming is forbidden underneath
the cooker hood.
• Always follow the instructions
provided on adjusting the
eciency of ventilation.
• Enable a sucient supply air flow
into the room if the cooker hood
and non-electric devices are used
simultaneously.
3 4

3© Vallox Oy - All rights reserved
MANUAL
12
4
min. 500 mm /
650 mm
3
Electrical connection
CAUTION
The minimum distance of the
bottom edge of the grease
filter to an electric cooker is
500 mm, and to a gas cooker
650 mm.
CAUTION
• The cooker hood must
not be connected to a flue
that is used for removing
combustion gases (e.g.
from a wood- or gas-
burning fireplace, cooker,
or stove).
• The cooker hood must
not be fastened through
the side panels to the
cabinets.
• Fans that are controlled
through the cooker hood
must have an engine
cover and their maximum
power must not exceed
340 W.
• Regulations on leading
extraction air outdoors
must be observed.
POWER PLUG
G23 LED
INSTALLATION
Use the mounting accessories included in the package
to fasten the cooker hood in place.
1. Shorten the extract air duct to be connected to the
hood (125 mm spiral duct) to the correct length.
2. Where required, install a Vallox cover strip, for
instance, (2142400 cover strip 500 or 2142500
cover strip 600) to cover the opening in the rear
wall.
3. Lift the hood so that it is in contact with the duct.
4. Fasten the cooker hood with the mounting
brackets or by other means, so that the hood is
firmly in place and cannot move (figures 1, 2 and
3). The mounting screws included in the accessory
bag are suited to walls made of wood, chipboard,
cement or stone. Use appropriate mounting
devices for other materials.
5. Check the tightness of the extract air duct system.
6. Plug the cooker hood into the mains. Ensure that
the plug can be unplugged, where required.

D11204/28.04.2023
www.vallox.com
Vallox Oy | Myllykyläntie 9-11 | 32200 LOIMAA | FINLAND