Vaxcel C0213 Instruction manual

Outlet Box
Set Screw
Mounting Screw (B)
Cross Bar (A)
Wire Connector (C)
Green Grounding Screw
Canopy
Swivel
Light Head
G45 LED Bulb Max.4W (D)
（included）
Glass Shade (E)
Hand Screw (F)
Cross Bar (A) Mounting Screw (B) Wire Connector (C)
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
C0213
Hardware Package (included):
WARNING:
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
181206
Turn off the power at fuse or circuit box
Installation Steps
3. Attach the canopy to the cross bar (A) by aligning
G45 LED Bulb Max.4W X 6 (D) Glass Shade X 6 (E)
1. Rotate the movable rod to the desired position of the canopy, then align the hand screw (G) to the desired hole and
tighten hand screw (G) .
2. Attach the cross bar (A) to the outlet box by using two mounting screws (B).
3. Pull out the outlet wires and the house grounding wire from the outlet box. Make wire connections by using the wire
connector (C) as follows.
--- Connect the black (hot) wire from the fixture to the black (hot) wire from the power source.
--- Connect the white (neutral) wire from the fixture to the white (neutral) wire from the power source.
--- Attach the fixture grounding wire to the cross bar (A) with the green grounding screw.
Then connect it to the house grounding wire with a wire connector (C).
Carefully put the wires back into the outlet box.
Hand Screw (G)

181206
A: 8"
B: 44"
Turn on the power at fuse or circuit box
Hand Screw (G)
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of
purchase. This warranty is limited to the correction of any such defect, or the replacement of any such defective
item(s), provided that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item (s)
is / are returned with proof of purchase date; and (c) it is found upon inspection by us that the item (s) is / are defective
as noted above. This warranty does not cover labor costs, consequential damages, nor does it apply to any item(s) that
have been improperly installed, overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s).
Finishes are specially excluded from the terms of this warranty since they are subject to environmental maintenance
deemed beyond our control. Other than the described obligation, we assume no further liability with respect to the sale
or use of our products.We make no warranty, express or implied, and disclaim any warranty of merchantability or fitness
for a particular purpose.
Assembly Kit
6066MM (1SET)
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Cross Bar (A) Mounting Screw (B) Wire Connector (C)
Hand Screw (F)
G45 LED Bulb Max.4W (D)
8105 LED
Glass Shade (E)
10080GS 6071MM 6072MM
3. Attach the canopy to the cross bar (A) by aligning holes, secure the set screws from the side hole of the canopy
into the hole in the side of the cross bar (A), then tighten the screws.
4. Attach the glass shade (E) to the light head, by secure the hand screws (F) through the holes on the light head to the
glass shade (E), then tighten the screws.
5. Attach the LED bulb (D) into the glass shade (E) and screw it to the light head, then tighten the bulb (D) in place.
Caution: LED Lamp, Type A or G, E12 base, maximum 25W X 6
Incandescent Lamp, Type A or G, E12 base, maximum 60W X 6
Notes: LED Dimmable bulb to be compatible with most LED Dimmers, recommended Lutron:
MSCL-OP153MH, MACL-153MH, DVWCL-153PH, TGCL-153PH, SCL-153PH.
6. Follow step 4 & 5 of instructions of single light head installation for other five light heads.
7. Adjust the light head to a desired position by using the swivel.