VDO Cyclecomputing HC12.6 User manual

CYCLECOMPUTING
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D´INSTALLATION ET D´UTILISATION
MANUALE D´INSTALLAZIONE E FUNZIONAMENTO
INSTALACION Y OPERACIÓN MANUAL
HANDLEIDING
HC12.6

P1
screw

P2 P3
1-5 mm

P4
LOCK
UNLOCK

P5
OPEN CLOSE

P6

P7
CLOSE
OPEN
IMPORTANT
Rubber washer

P8
Press MODE 2 for next
press MODE 1 to select
Press AC-Button to Begin
or install battery (P6)
•••••••
automatic
Press MODE 2 for next
press MODE 1 to select Press MODE 2 for next press MODE 1 to select
Press MODE 2 for next
press MODE 1 to select Press MODE 2 for next press MODE 1 to select Press MODE 2 for next press MODE 1 to select
Press MODE 2 for next
press MODE 1 to select
•••••••
•••••••
•••••••

P9
WS in mm / inch
1x

P10
ETRTO WS in mm KMH WS in inch MPH
47-305 16x1,75 1272 50,1
47-406 20x1,75 1590 62,6
34-540 24x1 3/8 1948 76,7
47-507 24x1,75 1907 75,1
23-571 26x1 1973 77,7
40-559 26x1,5 2026 79,8
44-559 26x1,6 2051 80,7
47-559 26x1,75 2070 81,5
50-559 26x1,9 2089 82,2
54-559 26x2,00 2114 83,2
57-559 26x2,125 2133 84,0
37-590 26x1 3/8 2105 82,9
20-571 26x3/4 1954 76,9
32-630 27x1 1/4 2199 86,6
40-622 28x1,5 2224 87,6
47-622 28x1,75 2268 89,3
40-635 28x1 1/2 2265 89,2
37-622 28x1 3/8 2205 86,8
18-622 700x18C 2102 82,8
20-622 700x20C 2114 83,2
23-622 700x23C 2133 84,0
25-622 700x25C 2146 84,5
28-622 700x28C 2149 84,6
32-622 700x32C 2174 85,6
37-622 700x37C 2205 86,8
40-622 700x40C 2224 87,6
ETRTO WS in mm KMH WS in inch MPH

P11
Start atTRIP DIST
Press MODE 1 for 3 sec. Press MODE 2 to select
between KMH and MPH Press MODE 1
to setWS1 Press MODE 2 to increase
Press MODE 1 to
switch and
MODE 2 to increase
continue for
all4 digits
Press MODE 2
to increase
Press MODE 1
to switch
•••••
Press MODE 1
3 sec. to end
••••••••••••
•••••••••••••••••••••••••••••••••••••••••••••••••••
Press MODE 1 to setWS2
Press MODE 1 3 sec.
to end without settingWS2
SETWS 1
SETWS 2
SET Metric System
•••••
••••••

P12
Press MODE 1
3sec.to start MODE 2 to
increase the hours
Press MODE 2 to
switch between
24h or 12h
Press MODE 1
to set the hours
Press MODE 1
3 sec. to end Press MODE 2
to increase the
minutes
Press MODE 1
to set the minutes

P14
P13
Set
Press MODE 1
3sec.to start Press MODE1 3 sec. to end after you set the navigator
Reset
Press MODE 2
to increase Press MODE 1 to switch
••••••••••••••••••••••••••
Important
Navigator in Display Press MODE 2
to reset
•••••••
•••••••

P15
Press MODE 1
3sec.to start Press MODE1 3 sec. to end
after you set
the odometer
Set ODOMETER
Press MODE 2
to increase Press MODE 1 to switch
••••••••••
•••••••

P16
Press any button
BIKE CHECK disappears The service icon will remain flashing. Another 50 km/35 mi. Then the service interval icon will also disappear
BIKE CHECK

P17

P18
Press MODE1
3sec. Press MODE1 to set Low Limit
Low-limit
High-limit
Set limits
Press MODE 2
to increase
Press MODE1
to end Press MODE 2 to decrease

P19
Press PULS Press MODE1+
MODE2 to stop Press MODE1+
MODE2 to start again

OWNER'S MANUAL - VDO HC 12.6
Index
Preface
1. Mounting 4.3 Entering time / clock
1.1 Handlebar holder 4.4 The NAVIGATOR
1.2 Speed transmitter (sensor) 4.4.1 Presetting the NAVIGATOR
1.3 Spoke magnet 4.4.2 Resetting the NAVIGATOR to zero
1.4 Twist-Click mounting of computer 4.5 Presetting the odometer
onto handlebarholder 5. Service interval indicator
2. Basic information on how to operate your VDO HC 12.6 6. Sleep mode
2.1 Interrogating information 7. Heart rate information of your VDO HC 12.6
2.2 Calling set-up mode 8. Putting on the chest belt
2.3 Button / key covering in set-up mode 9. Presetting your upper and lower heart rate limits
2.4 Resetting of information modes to zero 10. The stopwatch
2.4.1Cycling Information 10.1 Stopwatch (automatic)
2.4.2Heartrate Information 10.2 Manual operation of the stopwatch
2.4.3NAVI GATOR 11. Calling up your average heart rate
3. Installing the batteries 12. Display of training times within preset target range training zones.
3.1 Installing battery into computer head 13. Activating / deactivating the BEEPER
3.2 Installing battery into chest belt transmitter 14. FAQ / Troubleshooting
4. Initial set-up of your VDO HC 12.6 15. Warranty
4.1 Selecting your language 16. Technical data
4.2 Selecting the wheelsize 17. Packaging contents
4.2.1How to determine the precise wheelsize
4.2.2How to switch from wheelsize 1 to wheelsize 2
4.2.3Entering the precise wheelsize
1
GB
HC
12.6

Preface
Thank you very much for buying a VDO HC 12.6 bicycle computer featuring heart rate / pulse functions. The more familiar you get with this model,
the more enjoyable your trips are going to be.
Hence, our urgent request:
Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit
from all the technical features of your VDO HC 12.6.
We wish you enjoyable trips and rides on your bike with VDO
CYCLE PARTS GMBH
1.Mounting
1.1 Mounting the handlebar holder
The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand to operate
the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap and adjust it by tightening
the screw.
Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible
for you. Only when you find the best position tighten the screw. P1
1.2 Mounting the speed transmitter / sensor
The sensor should be mounted on the same side of the fork as the holder is on the handlebar. While mounting, be sure that there is ample cable
left for left and right turns of your handlebar, do not lay the cable too tight. P2
Important: Do not tighten the cable ties yet. Accurately position the sensor and the spoke magnet first, then tighten the cable ties.
1.3 Mounting the spoke magnet
Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current position, slide the sensor
and the magnet on the fork or spoke accordingly. P3
GB
HC
12.6
2