Vdwall LVP605 User manual

LVP605 SERIES
LED HD Video Processor
USER’S MANUAL

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
2
TABLE OF CONTENTS
I. Safety precautions 3
II. Packing list 4
III. Connections of hardware
1. Rear view 5
2. Port description 5
3. Connection diagram 6
IV. Frontal panel operations
1. Diagram of frontal panel 7
2. Button instructions (operation mode) 8
V. Setup
(I) User parameter setup 12
1. Enter setup of LVP605 12
2. Select language 12
3. Output image setup 13
4. Text Overlay Setup 14
5. Brightness / color / Sharpness 15
6. Audio configurations 18
7. Hot Spare setup
18
8. Factory district setup 19
(II) PIP/POP setup 20
(III) Mosaic setup 22
VI. Specifications 27
VII．ViewRGB LVP605 Control Software User’s Manual……….30
VIII．Notes to model……………………………………………………….42
IX．Copyright info………………………………………………………….42

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
3
I. Safety Precautions
Danger!
There is high voltage in the processor, to prevent any unexpected
hazard, unless you are maintenance, please do not open the cover of the
device.
Warning!
1. This device shall not encounter water sprinkle or splash, please do not
place anything containing water on this device.
2. To prevent fire, keep this device far from any fire source.
3. If this device gives out any strange noise, smoke or smell, please
immediately unplug the power cord from receptacle, and contact local
dealer.
4. Please do not plug or unplug DVI signal cable if the device is
powered on.
Caution!
1. Please thoroughly read this manual before using this device, and keep
it well for future reference.
2. In the event of lighting or when you are not going to use the device for
a long time, please pull the power plug out of receptacle.
3. Nobody other than professional technicians can operate the device,
unless they have been appropriately trained or under guidance of
technicians.
4. To prevent equipment damage or electric shock, please don’t fill in
anything in the vent of the device.
5. Do not place the device near any water source or anywhere damp.
6. Do not place the device near any radiator or anywhere under high
temperature.
7. To prevent rupture or damage of power cords, please handle and keep
them properly.
8. Please immediately unplug power cord and have the device repaired,
when
1) Liquid splashes to the device.
2) The device is dropped down or cabinet is damaged.
3) Obvious malpractice is found or performance degrades.

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
4
II. Packing list
Please unpack the product with care, then check whether all the following
things are included in the package. If anything is found missing, please contact
the dealer.
Standard accessories
The accessories supplied with this LED Video Processor may differ from the
figures contained in the User’s Manual, but they are applicable for the regions
where you live.
User’s Manual Power cord (1.5m)1pcs S-VIDEO cable (1.5m)
DVI cable (1.5m), 1pcs DVI cable (0.5m), 1pcs Disk
Rs232-RJ45 cable (1.5m) BNC-RCA adapter: 3 pcs PCB Connector (Audio)
Net cable(0.2m) DVI-I to VGA adapter(only for 605D)

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
5
III. Connections of hardware
1. Rear view
Figure 1
2. Port description
1）Video Input
LVP605 supports 10-channel signal input, including:
Port name Description
V1~V3 3-channel PAL/NTSC composite video input
S-Video 1-channel PAL/NTSC S-video input
YPbPr 1-channel component HD signal input
VGA1~VGA2 2-channel computer analog signal input
DVI 1-channel computer DVI digital signal input
HDMI 1-channel HDMI digital HD signal input
EXT. 1-channel extended signal input
EXT. input standard signal is 1xVIDEO, which can optically be
1xSDI/HD-SDI or 1xVGA/DVI/HDMI.
2）Audio Input
LVP605 supports 5-channel stereo audio switch. Of which, 3
channels are DVI (only available when the input signals are HDMI
signals), HDMI and SDI audios, the other 2 channels are AD1, AD2
external input audio. AD1 and AD2 can be mapped to the any one
of all video inputs, and will be switched synchronous to the
selection of video input signals.
3）Video Output
Port Description
VGA OUT 1-channel analog RGBHV signal output,

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
6
it can be connected to a local display
device and used as monitor (it is strongly
recommended to use this port when
operating and setting LVP605).
DVI OUT1 /
DVI OUT2
2 same DVI digital graphic signal output,
it can be connected with external LED
transmission card or LED transmission
box
SDI /HDSDI（OUT）
1-channel digital video signal loop output
(Only including this input with SDI/HDSDI
extended model)
DVI Loop OUT 1-channel computer DVI digital signal loop
output
4）Audio Output (AUDIO OUT)
Corresponds to the selected video input signal, output this
channel audio input signals.
5）Signals of other ports
RS232 command port is used to connect PC RS232. Then the
processor can be controlled by PC software. LOOP connector
can connect to another processors by net cable and one signal PC
can control all processors.
3. Connection diagram

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
7
IV. Frontal panel operations
1. Diagram of frontal panel
3
2
1
4
6
5
8
10
9
7
1）Input selecting buttons (V1, V2, V3, S-Video, DVI, VGA1, VGA2, YPbPr,
EXT.):
They are used to select input signals
2）Setup buttons (Setup, Save, ↑,↓,←,→)
They are used to set the image output parameters of the processor.
3）VGA auto adjustment (Auto)

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
8
To automatically adjust VGA input signals
4）Cut / Fade switching mode (C/F):
It is used to select signal switching effects, including seamlessly switching
(CUT)，0.5s, 1.0s and 1.5s Fade in / Fade out and blend.
5）PC signal bypass output (Bypass):
It is used to switch full screen/partial screen display of PC signals, and
the indicator will indicate the status of current input signal.
6）Info:
It is used to display current settings and information of processor
7）PIP/POP buttons (ON/OFF,M1，M2，M3，M4):
ON/OFF: to turn on/off PIP/POP functions, when the indicator is on,
you can select any signal coming from different groups or current signal as
PIP/POP by using input selecting buttons.
M1，M2，M3，M4: used to set or switch PIP/POP modes.
8) Mosaic
It is used to turn ON/OFF multi-machine cascade mosaic function. The
indicator indicates current splicing status.
9) Freeze
It is used to turn ON/OFF screen freezing function.
10) Text
It is used to add Text, company logo or animation.
2. Button instructions (operation mode):
There are 25 buttons on the frontal panel of LVP605, all these buttons
will be operable after start. they have the following functions as
described below:
1) Select input video source
Port name Description
V1、V2、V3 3-channel PAL/NTSC composite video input
S-Video 1-channel PAL/NTSC S-video input
YPbPr 1-channel component HD signal input
VGA1、VGA2 2-channel computer analog signal input
DVI 1-channel computer DVI digital signal input
HDMI 1-channel HDMI digital HD signal input
EXT. 1-channel extended signal input（such as SDI/HDSDI）
Switch audio input while operating above buttons; select the audio
signal input from corresponding video input to output it through Audio
OUT.
After selecting input signals, the input signal source you
currently selected such as “input=HDMI” will appear in the first line

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
9
of LCD, while the status of current input signals will appear in the
second line of LCD. If there are no valid signals entered, the
message “no signal” will appear in LCD, and the corresponding
indicator will blink and dark screen appear; if the signal is valid, the
format of input signals such as “ 1080p_60Hz ” will appear in LCD.
Input= HDMI
1080p_60Hz
Cut
Notes: if extended input was VGA/DVI/HDMI, we need choose
input signal by hand swithing to current signals. Switching to “VGA”,
the current input signal is VGA. Switching to “DVI”, the current input
signal is DVI or HDMI.
2) VGA input auto adjustment (Auto)
When the current VGA input source of LVP605 is a valid signal,
press this button, LVP605 will automatically adjust the sampling
parameters of the VGA signals, so as to make VGA picture clean
and complete.
In general, this operation is made only when new VGA signal
source is to be connected in. Sometimes user need repetitively do
such adjustment till VGA picture looks clean, complete and stable.
3) Information display (Info)
Press this button to view current settings and information of
LVP605, it consists of 25 items. If you press “Info” again before
LVP605 exit information display, LVP605 will continue to display
the next item of information.
4) Select Cut / Fade / Blend mode(C/F)
LVP605 can realize seamless switching effect (Cut) , fading
in/out switching effect (Fade) or blend effect between any two
signals from different groups as listed below.. But if the signals
come from the same group, dark screen will appear.
A B C D
V1，V2, V3,
S-Video
DVI，
HDMI
VGA1
VGA2
EXT
Cut (seamlessly switching): while in this mode, “Cut” will

LVP605 Series User’s Manual
---------------------------------------------------------------------------------------------------
LED VIDEO PROCESSOR
10
appear in the third line of LCD, the system can seamlessly switch
between different signals. It is also the default mode of LVP605
after startup.
Fade (fading in fading out): while in this mode, “Fade=1.0s” will
appear in the third line of LCD, the system can realize fading in
fading out switching effect between the signals coming from
different groups. Users can set the switching time of fading in and
fading out as 0.5 seconds,1.0 second or 1.5 seconds.
Blend: The current input signal will be the background. The
other signal from different group will be choosed as blend signal.
Then the background signal and blend signal will be overlap
showed. Then press the button of background or blend signal, the
output will be the choosing signal. The whole procedure will be fade
in fade out switching effect.
Notes: Neither Cut mode nor Fade modes applies to YPbPr
signals, that is to say, if you attempt to switch between YPbPr
signals and any other signal, dark screen will appear. YPbPr signal
cannot be background signal and blend signal.
5) PIP / POP（PIP/POP：On/Off，M1, M2, M3, M4）
PIP/POP mode of LVP605 allows user to insert a PIP window in
current picture, and the size and location of the PIP window can be
set freely. The signals to be displayed in PIP window can be either
current signal itself or any signals which are not in the same group
as that of current picture. Here we call current picture “background”,
and call the picture to be overlaid “PIP”. The following paragraphs
will illustrate the operating procedures of this function:
Enter PIP display mode: Press On/Off button, its indicator will
illuminate, LVP605 will enter PIP display mode, then use Preselect
button to select PIP input signals, in the meantime, signals of
background and PIP and their locations will appear in LCD (see
Figure below):
Background：V1
PAL
PIP：VGA
1280X1024 60Hz
Change PIP: While in PIP mode, use Preselect button to select
proper input signals, the preselected signals will be set as PIP.
Change the background: you must first turn off PIP mode.