Velleman Dk-2800 User manual

SPLIT-DECODED CONTROLLER

FOR DK-2800 SECURITY KEYPADS

DA-2800 & DA-2801

Installation & Operation Manual

FOR ELECTRIC LOCK, INTER-LOCK

AND SECURITY SYSTEM INSTALLATIONS

VERSION: 10/2010

AEI

PROTECT-ON

SYSTEMS

LIMITED

www.apo-hk.com

RoHS

Compliance

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference

that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

TABLE OF CONTENTS

INTRODUCTION

FEATURES

SPECIFICATIONS

PACKAGE CONTENTS

THE SPLIT-DECODED CONTROLLER UNIT (Figure 1)

THE MAIN CIRCUIT BOARD OF THE CONTROLLER --- (Figure 2)

INSTALLATION

Precautions

Split-Decoded Mode -- (For DA-2800 & DA-2801)

The Necessary Connections For Split-Decoded

The Function Mode Jumper Setting For Split-Decoded -- (DA-2800 Only)

The Link-Up Jumper & Link-Up Code Acquisition

The Function Mode Jumper -- (Available On DA-2800 Only)

CONNECTION TERMINALS

The Audible & Visible Signals

The Alarm Outputs & Warnings

RF Remote Controller -- (DA-2800 Only)

Stand Alone Mode -- (DA-2800 Only)

APPLICATION EXAMPLES

Basic Wirings of A Split-Decoded Door Lock

Basic Wirings of An Inter-Lock System Using Two Split-Decoded Keypads

APPLICATION HINTS FOR THE AUXILIARY TERMINALS

PROGRAMMING FOR FULL FEATURES --- (Supplementary Information)

Set System in Programming Mode with The Master Code

Direct Access to Programming Mode with The “DAP” Code – 8 0 8 0

Refresh The System with The “Refreshing Code” --- 9 9 9 9

The Default Values of The Keypad

FEATURE PROGRAMMING -- KEY IN AND STORE THE DESIRED VALUES

Programming Criteria for Codes

Record A Master Code

Record A Super User PIN

Operation And Functions of The Super User PIN

Record The Common User PINs for Output 1, 2 & 3

Record-Delete PINs or Cards for Output 1, 2, & 3

Examples – Programming And Operation

Visitor Codes (For Output 1 Only)

Duress Codes (For Outputs 1, 2 & 3)

The Operation And Function of The Duress Code

Configuration of The Output Modes for Output 1, 2 And 3

Personal Safety And System Lock-Out

..........................................................................................4

..............................................................................................4

..........................................................................................5

.....................................................................................5

............................................................6

.................................................6

............................................................................................7

.............................................................7

...............................................................8

.........................................8

.............................................................8

....................................................9

.................................................................................1 0

............................................................................1 4

..........................................................................1 4

...................................................................1 5

.....................................................................1 5

.................................................................................1 6

................................................................1 6

.......................................1 7

.......................................................1 8

.........................................2 1

....................................................2 1

...........................................2 2

..................................................2 3

.......................................................................2 3

........................................2 4

..........................................................................2 4

..................................................................................2 5

...............................................................................2 5

.............................................................2 6

.........................................................2 6

............................................................2 7

...............................................................2 8

........................................................................3 0

....................................................................3 1

.........................................................3 2

....................................................3 3

...................................................................3 3

8 0 Door Forced Open Warning

& Time

FUNCTION MODE / TIME:

0---OFF

1-999 Seconds 80 FUNCTION / TIME #

Mode = 0,

Door Forced

Open

Warning OFF

8 1 Propped-up Warning & Time 81 FUNCTION / TIME # Mode = 0,

Propped-up

Warning OFF

9 0 Egress Delay Warning &

Alarm

CODE 1

FUNCTION MODE:

1---Momentary, No warning

2---Momentary, with warning

3---Momentary, with warning +

Alarm

4---Hold Contact, No warning

5---Hold Contact, with warning

6---Hold Contact, with warning

+ Alarm

CODE 2

DELAY TIME:

0---No Delay

1-99 Seconds

90 CODE 1 CODE 2 #

Mode = 1

Momentary,

No warning

TIME = 0

No Delay

9 1 Door Opening Alarm &

TIMER

ALARM TIME:

0---No Alarm

1-999 Seconds

91 ALARM TIME # Time = 0,

No Alarm

9 4 Operation Mode & Wiegand

Output

MODES OF WIEGAND OUTPUT

0---Stand Alone Keypad

Valid

Codes & Cards Only

1---Reader

All Codes & Cards

2---Master Keypad

Valid Codes

& Cards only

3---Slave Keypad

Valid Codes

& Cards only

94 WIEGAND O/P MODE # Mode = 0

Keypad Mode

SYSTEM CODES FUNCTION CODE ENTRY RESULTS

0 0 0 0

Factory Set Master Code

for User to set system in

programming Mode at the

first time.

THIS IS NOT A PERMANENT

SYSTEM CODE & IT IS

CHANGED IF A NEW MASTER

CODE IS PROGRAMMED.

0000 * *

NEW MASTER CODE * *

System in Programming Mode

9 9 9 9

REFRESH CODE -- Refresh

the system and set all its

function back to default

values.

9999 # All programmed data are cleared and

back to the default values except the

Master Code

8 0 8 0

DAP CODE-- Direct access

to programming mode. Valid

only in the power-up delay

period

8080 # System in Programming Mode

0 9 9 9

USER PINs / Codes / Cards

whole group clearance Code

Key in the Code to clear all

the users in the Location

LOCATIONS:

10--- User Group 1

20--- User Group 2

30--- User Group 3

40--- Vistor Group

41--- Duress Group 1

42--- Duress Group 2

43--- Duress Group 3

LOCATION NO. 0999 # Whole group of users in the selected

location are cleared

* * Exit Programming Code ** The system back to normal opration

after programming

User PIN Entry Mode

Pacifier Tones On-Off Selection

Output Operation Announcer

Status LED Flashing On-Off during Standby

Door Forced Open Warning & Timing

Door Propped-Up Warning & The Delay Time

Intelligent Egress Button – An Unique Feature of A Contemporary Keypad

Where And Why “Going Out” Needs Attention

Egress Delay , Warning And Alarm

Configurations of The Egress Warning And Alarm

Door Opening Alarm & Timer

Close The Programming Mode

The Operation Modes and The Wiegand Output

Wiegand Output at Keypad Operation Mode

PROGRAMMING SUMMARY CHART --- (Supplementary Information)

...................................................................................3 4

..........................................................................3 4

.............................................................................3 4

.................................................................3 5

.....................................................................35

..............................................................3 5

.......................................3 6

.............................................................3 6

........................................................................3 7

.........................................................3 7

.............................................................................3 8

...........................................................................3 8

..............................................................3 9

............................................4 0

THE PROGRAMMING SUMMARY CHART --- (Supplementary Information)

LOCATION FUNCTION ENTRY LIMITS & CODE

OPTIONS CODE ENTRY FACTORY

DEFAULT

0 1 Master Code 4-8 Digits 01 MASTER CODE # NIL

0 2 Super User PIN 4-8 Digits 02 SUPER USER PIN # NIL

0 3 Common User PIN for O/P 1

4-8 Digits

03 COMMON USER PIN 1 # NIL

0 4 Common User PIN for O/P 2 04 COMMON USER PIN 2 # NIL

0 5 Common User PIN for O/P 3 05 COMMON USER PIN 3 # NIL

1 0 User PINs / Cards for O/P 1

CODE 1

MEDIA:

1---EM Card

2---Private User PIN

3---EM Card+Sec User PIN

4---EM Card+Com User PIN

5---Deletion of User PIN

CODE 2

USER ID:

000-999---Group 1(10)

001-100---Group 2(20)

001-100---Group 3(30)

CODE 3

USER PINs / Cards:

4-8 Digits / Cards

10 CODE1 CODE2 CODE3 #NIL

2 0 User PINs / Cards for O/P 2 20 CODE1 CODE2 CODE3 #NIL

3 0 User PINs / Cards for O/P 3 30 CODE1 CODE2 CODE3 #NIL

4 0 Visitor Codes

CODE 1

VISITOR ID: 01-50

CODE 2

VALID PERIOD:

00---One Time

01-99 Hours

CODE 3

VISITOR CODE:

4-8 Digits

40 CODE1 CODE2 CODE3 #NIL

4 1 Duress Code for O/P 1 CODE ID

O/P 1: 01-50

CODE ID

O/P 2: 01-10

CODE ID

O/P 3: 01-10

DURESS CODE: 4-8 Digits

CODE ID

DURESS CODE

# NIL

4 2 Duress Code for O/P 2 42

CODE ID

DURESS CODE

# NIL

4 3 Duress Code for O/P 3 43

CODE ID

DURESS CODE

# NIL

5 1 O/P Mode for O/P 1 OUTPUT MODE & TIME:

0--- Start / Stop

1---99999 Seconds,

Momentary

51 O/P MODE & TIME # 5 Seconds

5 2 O/P Mode for O/P 2 52 O/P MODE & TIME # 5 Seconds

5 3 O/P Mode for O/P 3 53 O/P MODE & TIME # 5 Seconds

6 0 Personal Safety & Lock-out

LOCK-OUT CODE:

1---10 Trial, Lock-out 60 Sec.

2---10 Trial, Activates Duress

5-10---5-10 Trial, Lock-Out 15

Minutes

00---No Lock-out

60 LOCK-OUT CODE #

Code = 1,

10 Trials,

Lock-out 60

Seconds

7 0 PIN Entry Mode

ENTRY MODE:

1---Auto Mode

2---Manual Mode

70 ENTRY MODE # Mode = 2,

Manual Mode

7 1 Pacifier Tone ON-OFF

FUNCTION MODE:

0---OFF

1---ON

71 FUNCTION MODE # Mode = 1,

Pacifier Tone

7 2 Output Announcer 72 FUNCTION MODE # Mode = 1

Announcer ON

7 3 Standby LED Flashing 73 FUNCTION MODE # Mode = 1,

Flashing On

INTRODUCTION

The DA-2800 or DA-2801 is a self-contained access controller. It has been designed mainly as the decoder unit

working together with the keypads in the DK-2800 series to make up a split-decoded keypad system.

In split-decoded operation the system provides full Tri-Tech features of accepting EM Card, PIN/Code and RF Remote

Control. This unique design philosophy makes the system to provide high level of security in preventing sabotage far

ahead of the traditional stand alone keypad systems.

The DA-2800 also has been designed to work stand alone without keypad. The three relay outputs can be controlled

by the RF remote control key directly. The Output 1 operates in Start/Stop mode or in Momentary mode with the built-

in adjustable timer for door strike. The Output 2 and 3 operate in Start/Stop mode and manually controlled Momentary

mode respectively.

DA-2801 is the simplified version without the RF remote control function. It is solely a full feature decoder of the DK-

2800 series keypads in Split-decoded operation.

The DA-2800 or DA-2801 has three output relays and a built-in door chime. It is an ideal device for Door Strike, Alarm

Arm-disarm control and actuation of Automatic Operator, such as garage door opener.

The keypad system with the DA-2800 or DA-2801 decoder in Split-decoded operation offers full features performance

even the keypad is just a simplified version. Maximum three keypads can be connected in parallel to the decoder unit

with one of them setting in master mode and the other two setting in slave mode. Each keypad can be programmed

with its own PINs and Cards. The slave keypads take the features and the functions programmed in the master keypad

to operate the system. The decoder interprets the data and operates the desired functions faithfully.

FEATURES

DA-2800 – Full Feature Decoder + RF Remote Control

DA-2801 – Full Feature Decoder

I) DA-2800 & DA-2801

• A Decoder for The DK-2800 Series Keypads in Split-decoded Operation

• Decodes The Data of EM Cards, PINs / Codes & Functions Faithfully from Keypads

• Provides Full Features in Split-Decoded Mode for Any Keypad in The DK-2800 Series

• Simple Three Wires Connection to Keypads For Data Communication, (+), (

) & Data I/O

• Easily to Set Up Link Up Code with The Keypads And The Decoder

• Three Independently Controlled Output Relays

• Built-in Door Chime

• Built-in Alarm for Tamper, Door Forced Open and Door Opening in Split-Decoder Mode

• Built-in Current Limited (750mA) Power Source for The Keypads to Prevent Sabotage of Short Circuit from Outside

II) DA-2800 Only

• Provides The Tri-Tech Features of RF Remote Control, Card and PIN/Code Reading in One System

• 24 bits Self-learning Codes (over 1 million codes) for The RF Remote Control Keys

• Accepts 40 RF Remote Control Keys Maximum

• 4 RF Remote Control Channels for Stand Alone or Split-decoded Operation

• Remote Control Key Controls Output 1, 2, 3 & Door Chime

CLOSE THE PROGRAMMING MODE ( * * )

Always close programming mode with * * to set system back to normal Operation after programming.

The button is equivalent to the * button in the keypad with bell button.

VALIDATION

** --------------- System is back to normal operation mode

THE OPERATION MODES AND THE WIEGAND OUTPUT (Location 94)

Four operation modes are available for the selection. The codes are 0, 1, 2 and 3.

WIEGAND OUTPUT AT KEYPAD OPERATION MODE

0 --- Stand Alone Keypad Mode -- (Default)

The system provides full functions to operate its outputs and at the same time provides Wiegand Data Output for all the

VALID Cards and User PINs including the Duress Codes and Visitor Codes. No Wiegand Data Output for the invalid PINs

and Cards.

1 --- Card & Code Reader Mode

In the Card & Code Reader Mode, the keypad provides Wiegand Data Output for all the Card readings and PINs/Code

entries but does not operate its outputs. It is solely a card and code reader.

NOTE:

It is suggested to clean all the codes, PINs and cards that were previously stored in the system before setting the

system for reader mode.

2 --- Master Keypad of Split-Decoded Mode (The Only Mode will Send Out the Link-up Code)

The keypad unit provides the Wiegand Data Output for the valid user PINs, Codes and Cards exactly like in the Stand

Alone Mode. The Master keypad will transfer all the programmed feature data (except the user PINs, Codes and Cards

data) to the Access Controller (decoder) right after it exits the programming mode. A Split-decoded keypad system

needs at least one Master keypad and one Access Controller to work.

3 --- Slave Keypad of Split-Decoded Mode

The Keypad unit provides the Wiegand Data Output for the valid user PINs, Codes and Cards exactly like in Stand Alone

Mode. No feature data is transferred to the Access Controller (decoder) from the Slave keypad. It takes the same feature

data from the Master keypad to operate. The Slave keypad(s) is for a Split-Decoded system that needs more than one

keypads for operation convenience.

NOTE:

a) Do not set more than one keypads in Master mode in a Split-Decoded system. Otherwise, the data will be confused.

b) Each keypad in Split-Decoded mode can be programmed independently with its own user PINs, Codes and Cards.

The PINs, Codes and Cards can be repeatedly used in other keypads in the same system.

OPERATION MODELOCATION VALIDATION

#0 , 1 , 2 or 394

INDIVIDUAL

SPECIFICATIONS

Operating Voltage:

12V-24V DC, Auto Adjusting

Operating Current:

65mA (quiescent) to 100mA (three relays active)

Operating Temperature:

-20 C to +70 C

Environmental Humidity:

5-95% relative humidity non-condensing

The Adjustable Timer for Output 1:

1-30 Seconds

Power Up Delay:

5 Seconds

Tamper Alarm:

3 Minutes

Input Sensing Terminals:

a) Door position, b) Egress, c) O/P 1 Inhibit, d) Door Bell, e) Tamper

Output Control Terminals:

a) Duress, b) Alarm, c) Key Active, d) Inter-lock;

Transistor Open Collector, 24VDC/100mA sink Max

Output Contact Ratings:

Output Relay 1 – N.C. & N.O. dry contacts, 5A/24VDC Max.

Output Relay 2 – N.C. & N.O. dry contacts, 1A/24VDC Max.

Output Relay 3 – N.C. & N.O. dry contacts, 1A/24VDC Max.

Dimensions:

32.5(H) X 120(W) X 87(D)mm Plastic Box

Weight:

250g net

RF Remote Controller (DA-2800 Only) :

Number of Self-leaning Codes : Over 1 Million

Number of RF Control Keys : 40 Maximum

4 Control Channels : Output 1, 2, 3 & Door Chime

Operation Frequency : 433.92MHz

Control Distance : 60 Meters Approx. in Open Space

Receiver Type : Super-heterodyne

Operation Voltage : 12V Alkaline Battery, Type 27A (Battery Not Included)

Weight : 32g

Specifications are subject to change for modification without notice

PACKAGE CONTENTS

• One Access Controller

• One Pack of Mounting Screws

• Two RF Remote Control Keyfobs (DA-2800 Only), Battery Not Included

• One Owner’s Manual

EXAMPLES:

Example 1: Set Egress Button in Momentary contact 5 seconds with delay & warning beep

90 2 5 #

(a) (b) (c) (d)

(a) Egress function programming, (b) Momentary contact with warning, (c) Delay time of 5 seconds to release door,

(d) Entry confirmation

Example 2: Set Egress Button in Holding contact of 10 seconds with warning beep

90 5 10 #

(a) (b) (c) (d)

(a) Egress function programming, (b) Holding contact mode with warning, (c) Holding time of 10 seconds to release

door, (d) Entry confirmation

Example 3: Set Egress Button in Momentary contact without delay (This is the default setting)

90 1 0 #

(a) (b) (c) (d)

(a) Egress function programming, (b) Momentary contact without delay, (c) Release door instantly, (d) Entry

confirmation

DOOR OPENING ALARM & TIMER (Location 91)

ALARM & TIMING OF DOOR OPENING

0 --- No Alarm – (Default)

The Alarm Output is disabled

1 – 999 --- Alarm Timer

The Door Open Alarm operates the Alarm Output (Terminal 13) only. It is mainly prepared to trigger an optional alarm

system. Put any Timing Figure of 1 to 999 into the box to enable the function of the Door Opening Alarm. The figure

is the time in second of the alarm duration, which starts to count after the door is opened and it resets automatically

when the time reaches.

The alarm can be stopped with the User Codes/Cards or the Super User PIN for Output 1 at any time before the end

of the alarm time.

NOTE: The Door Opening Alarm is designed to protect the emergency exit door from use by the un-authorized person.

The alarm occurs when the door is opened or forced to open. However, Alarm will not happen if the door is opened with

a valid User Code or Card.

The Manner of The Door Opening Alarm:

a) The door is forced to open without using PIN/Card – Alarm

b) The door is opened with Egress Button – Alarm

c) The door is opened with PIN/Card – No Alarm

To prevent confusion of the alarm outputs. It is suggested to disable the "Door Forced Open Warning" at Location 80

while "Door Opening Alarm" function is enabled. If both functions at Location 80 and Location 91 are enabled and are

set with different timings, the system will combine them and will take the longer one for alarm time.

ALARM TIME VALIDATION

LOCATION

0 or 1

99991 #

MASTER

THE SPLIT-DECODED CONTROLLER UNIT (Figure 1)

THE MAIN CIRCUIT BOARD OF THE CONTROLLER --- (Figure 2)

NOTE: Factory suggest that the work of timer adjustment and change of jumper settings on the main circuit board are

to be done by the Installer only.

No adjustment/setting change is required for Split-decoded operation with the ex-factory settings.

LINK-UP JUMPER

OFF-->ON-->OFF

CODE LEARNING

BUTTON

(DA-2800 ONLY)

REMOTE CONTROL

SIGNAL & STATUS

(DA-2800 ONLY)

INTERNAL SIREN

& DOOR CHIME

CONNECTION

TERMINALS

MAINS

OUTPUT BEEP JUMPER

ON OR OFF

FUNCTION MODE JUMPER

1. SPLIT-DECODED

2. STAND ALONE MODE 1

3. STAND ALONE MODE 2

ADJUSTABLE TIMER

FOR OUTPUT 1

TURN CLOCKWISE FOR

MAXIMUM TIME

RECEIVER FOR

REMOTE CONTROL

(DA-2800 ONLY)

EGRESS DELAY , WARNING AND ALARM (Location 90)

CONFIGURATIONS OF THE EGRESS WARNING AND ALARM

Key in the number to enable 1 of the 6 configurations described below:

1 --- Momentary Contact Mode without Warning -- (Default)

• Press the Button once. No warning or alarm is given during Egress Delay.

• Good for silent area. The people have to wait for the door open until the delay time

reaches.

2 --- Momentary Contact Mode with Warning Beep

• Press the Button once. The system gives Warning Beeps during the Egress Delay.

• Good for the place required attention. The keypad beeps during the people are waiting for

the door open.

3 --- Momentary Contact Mode with Warning Beep & Alarm

• Press the Button once. The system gives Warning Beeps and also activates its Alarm O/P

during the Egress Delay

• Good for door for the authorized people only. The keypad beeps and report alarm to a

security system during the people are waiting for the door open.

• This is usually an “Emergency Exit”. The door can be opened with the Keypad without

triggering of the Buzzer and Alarm Output.

4 --- Holding Contact Mode without Warning

• Press and hold the Button. No warning or alarm is given during the Egress Delay.

• Good for the silent area. The people require to press & hold the button until the delay time

reaches for the door open.

5 --- Holding Contact Mode with Warning Beep

• Press and hold the Button. The system gives Warning Beeps during Egress Delay.

• Good for the place required attention. The keypad beeps while the button is kept pressed

during the people are waiting for the door open.

6 --- Holding Contact Mode with Warning Beep & Alarm

• Press and hold the Button. The system gives Warning Beeps and also activates its Alarm

O/P during Egress Delay.

• This is usually an “Emergency Exit”. The door can be opened with the Keypad without

triggering of the Warning and Alarm.

EGRESS DELAY TIMER

0 --- No Delay – (Default)

Output 1 activates instantly (the door is released instantly) when the Egress Button is pressed.

1 – 99 --- Egress Delay Timing

Put any number of 1 to 99 into the box to enable the Egress Delay. The number is the time in second, which starts to

count when the Egress Button is pressed. Output 1 activates (the door is released) when the delay time reaches.

NOTE:

1) Momentary Contact -- The Egress Delay starts to count when the egress button is momentarily pressed. Output 1

activates automatically (door is released) when the delay time reaches.

2) Holding Contact -- The user MUST hold the egress button in contact for the whole period of the Egress Delay time

until Output 1 activates. If the egress button is released before the end of the Egress Delay, the timer will stop to count

and reset.

3) The Egress Delay does not affect the operation of the User PINs/Cards for Output 1. The User PINs/Cards always

give INSTANT action.

Examples: (please see the following page)

FUNCTION MODES VALIDATIONDELAY TIMELOCATION

6 0 or 1

99 #90

MASTER

INSTALLATION

PRECAUTIONS

1) Installation Location:

The built-in receiver of the Access Controller is working at the UHF frequency band of 433.92MHz. To get the best

receiving result of the signals from the remote keys a correct installation location is necessary.

i) Install it on a location inside the house facing to the open space and there has no strong electro-magnetic wave

signals near it.

ii) Do not install it in a concrete room or under a concrete stair, which shortens the control distance.

2) Prevent Accidental Short Circuit:

In the previous experience, most of the damages caused in the installation are accidental touching of the components

on circuit board with the wires carrying power. Please be patient in the installation. Study the manual to become

familiar with the specifications of the system beforehand is also important.

i) Do not apply power to the system while it is in installation.

ii) Check carefully all the wirings are correct before applying power to the system for testing.

SPLIT-DECODED MODE -- (for DA-2800 & DA-2801)

Split-decoded Mode needs at least one keypad to work with the decoder. The decoder decodes all the commands

from the keypad to operate its outputs. It is an unique solution to immediately up-grade a general purpose keypad to a

high security access control system. All the keypads in the DK-2800 series with Data I/O Port are compatible with the

decoder. A Split-decoded system divides itself into the outside keypad unit and the inside decoder unit. Any sabotage to

the outside unit does not affect the security of the inside unit.

RF WIRELESS

REMOTE CONTROL (DA-2800 ONLY)

DOOR LOCK

(OUTPUT 1)

SECURITY

SYSTEM (OUTPUT 2)

AUTOMATIC

OPERATOR (OUTPUT 3)

COMMON

GROUND

COMMON

GROUND

DA-2800 OR DA-2801

SLAVE 1

SLAVE 2

MASTER

DATA I/O

COMMON

GROUND

DATA I/O

MAXIMUM 3 KEYPADS CAN BE CONNECTED IN PARALLEL

INTELLIGENT EGRESS BUTTON – AN UNIQUE FEATURE OF A CONTEMPORARY KEYPAD

Most of the keypads for access control are just for controlling of “Going In” from outside. It is not enough for today’s

access control systems. In fact, controlling of “Going Out” is also very important in many public passage areas. They

are not allowed to use locks or digital keypads for stopping of “Going Out” due to safety reasons. Such as hospitals,

kindergartens, elderly homes, convenient stores, emergency exits etc.. The wardens, teachers, shopkeepers and the

guards are always required to keep an eye on people to prevent unattended leaving, shoplifting, and illegal use of the

emergency exits.

The Intelligent Egress Button can be programmed to do something to get the attention of the person on duty before the

door is opened. The button offers programmable egress delay, delay with warning, holding button required for the delay,

momentary button contact with warning for the delay and even gives alarm when a controlled door is opened.

Locations 90 and 91 below are the places for setting the desired functions for the Egress Button.

The functions programmed to the Egress Button do not affect the normal operation of the system with its keypad. For

the safety consideration, the operation of the keypad with PIN, Code or Card is always in the first priority to give instant

action to the output relay 1 for door strike.

It is NOT required to program the Egress Button with the special function in normal use. Just leave it on its default

values.

WHERE AND WHY “GOING OUT” NEEDS ATTENTION

Examples for some areas may need an Intelligent Egress Button:

Hospital:

Some of the patients are not allowed to leave the ward without doctor’s permission. An egress button with exit delay

and warning beeps will help the nurse or warden to get the attention to the door when the egress button is pressed.

Further setting of the egress button with holding contact for the delay even gives higher level of security to a controlled

door.

Kindergarten:

Young children are always active. Some of them may be willing to go out to explore their ways of playing. For safety

reason, teachers have to watch all of them in the attended area. Leaving school alone without the companion of parents

or teacher is dangerous to the young children. An egress button with delay and warning beeps will be helpful to prevent

the children trying to go out without getting the attention of the teacher.

Elderly Home:

Elderly needs constant attention and care. Some old people have poor memory. They may forget the way to come

back if they leave home alone. An egress button with delay and warning beep will easily get the attention of the warden

before the door is open.

Convenient Store:

Most of the convenient stores have just only one or two shopkeepers on duty. They are usually the cashier. Shoplifting

may easily happen while the shopkeeper is busily serving customers at the cashier desk. A holding contact egress

button with delay and warning beeps may help to stop most of the shoplifting. As the thief knows that he is gotten

attention by the shopkeeper before the door is open.

High Traffic Passage:

A short buffer time may be necessary for opening a door outward after pressing the egress button for those exits open

to a high traffic passage. An egress button with short delay and warning beeps helps the user to pay attention to the

people passing by to prevent hitting them when the door is pushed outward.

Emergency Exit:

Emergency Exit is not open to the public for daily use. It is for emergency case only. It is usually closed and watched

by the security guards. The egress button of this keypad can be programmed to offer exit delay with warning beeps and

even gives alarm output to trigger an alarm system when the door is forced to open or the door is open after the exit

delay expired. It is an useful tool to get the attention of the person on duty.

THE NECESSARY CONNECTIONS FOR SPLIT-DECODED

1) Connect the Data I/O ports of the Decoder (Terminal 4) and the Keypad with wire to link-up the communication of

the two units.

2) Connect the Keypad PWR terminal of the Decoder (Terminal 3) to the keypad power input terminal, which supplies

power to the keypad unit with current limit protection.

3) Connect the Common (

) Ground (Terminal 2 or 11) to the (

) ground of the keypad unit to make up the return path

for the data and the power source.

4) Make all other installation connections to the decoder unit, but not to the keypad unit in Split-Decoded Mode. The

system provides full feature from the decoder unit according to the functions programmed in the keypad.

THE FUNCTION MODE JUMPER SETTING FOR SPLIT-DECODED -- (DA-2800 ONLY)

NOTE: No Function Jumper setting is required for the DA-2801. It is fixed in Split-Decoder mode.

1) Put the “Function Mode Jumper” to position “1” for Split-Decoder. (It is an Ex-factory Setting)

a) The Function Jumper of the DA-2800 has been put on Position 1 at the factory. Setting of the jumper is usually not

necessary unless it has been changed. Always put jumper on position “1” for Split-decoded mode.

b) The Function Jumper is located on the Main Circuit Board inside the box. Change the setting for Stand Alone mode is

required. See Figure 2.

2) Set the “Link-up Jumper” from OFF to ON position to enable the link-up of acquiring the link-up code from

the keypad (same as the Master Code of the keypad).

a) The Jumper is located on the main circuit board inside the terminal compartment. See Figure1.

b) The Decoder executes link-up Only Once. The Link-up execution is done when the keypad exits from Programming

Mode after pressing **. Put the jumper back to OFF position after link up.

c) After the decoder knows the link-up code (Master Code) of the keypad it is not necessary to repeat the link-up

procedure in feature change programming except change of the Master Code.

Remark:

a) All the keypads going to link up with the decoder MUST be with the same Master Code which is the authorization

code to enable the data communication between the keypads and the decoder.

b) It is not necessary to repeat the link-up procedures for the slave keypads with the same Master Code. Just simply

connect them in parallel with the master keypad.

c) The decoder will refuse other keypads that are not in the same Master Code to link up with it.

d) The failed keypads in the link-up will generate warning beeps.

THE LINK-UP JUMPER & LINK-UP CODE ACQUISITION

To acquire the link-up code (same as the Master Code) from the Master keypad for Split-Decoded operation is

necessary. At any time, when you operate a new Master keypad at the first time it is necessary to let the decoder unit

to know the Master Code of the keypad. Otherwise, the decoder can not recognize the data from it. If more than one

keypads are going to link up with the decoder, all the keypads are required to have the same Master Code and repeat

link-up is not necessary.

The decoder executes Link-up Acquisition Only Once at the moment after setting of the Master Keypad to exit

Programming Mode with **.

STATUS LED FLASHING ON-OFF DURING STANDBY (Location 73)

STANDBY FLASHING ON-OFF

Some people find the flashing light of the status LED (the amber LED) is annoying during the keypad is on standby,

especially at the night time. The standby flashing can be ON-OFF with the setting here.

1 --- Standby Flashing ON -- (Default)

The Status LED gives Standby Flashing all the time during the keypad is on standby. It also gives all the light

indications showing the operation status of the system.

0 --- Standby Flashing OFF

The Standby Flashing is disabled but it does not affect the system status indications. All the light indications from it

are unchanged.

DOOR FORCED OPEN WARNING & TIMING (Location 80)

DOOR FORCED OPEN WARNING ON-OFF & TIMING

The Door Forced Open Warning function requires a Door Position Sensing switch (usually a magnetic contact) to work

with. Once a Timing Figure is put into the Function Mode box, the warning mode is enabled.

0 --- Door Forced Open Warning OFF – (Default)

999 --- Door Forced Open Warning & Alarm ON & Timing

The Timing Figure for the Warning can be 1-999 seconds. The keypad generates the door forced open warning

beeps and activates the alarm output (Terminal 13) instantly if the door is forced to open without a valid User PIN/

Card or pressing of the Egress Button. The beeps and alarm will last as long as the time set on the timer and it can

be stopped at anytime with an User PIN/Card in Group 1 before the end of the time.

The Manner of The Door Forced Open Warning:

a) The door is forced to open (without using PIN/Card or Egress Button) – Warning & Alarm

b) The door is opened with PIN/Card – No Warning or Alarm

c) The door is opened with Egress Button – No Warning or Alarm

DOOR PROPPED-UP WARNING & THE DELAY TIME (Location 81)

DOOR PROPPED-UP WARNING ON-OFF & TIMING

If somebody opened the door and it is left open longer than the allowable delay time, the keypad will generate door

propped-up warning until the door is re-closed. There is warning beeps from the keypad only but does not activates

the alarm output.

0 --- Door Propped-up Warning OFF – (Default)

999 --- Door Propped-up Warning ON & The Delay Time

The Delay Time can be 1 to 999 seconds. It is the time allows the door to open without starting of the warning.

FUNCTION MODES

VALIDATION

LOCATION

0 or 1

999

0 or 1

999

FUNCTION MODES VALIDATIONLOCATION

1 or 0 #73

MASTER

INDIVIDUAL

Example – Change of the Link-up Code ( The Master Code of the Master Keypad)

a) Put the Link-up Jumper of the Decoder from OFF to ON

OFF ON

b) Set the Master Keypad to Programming Mode

EXISTING MASTER CODE * *

c) Set a New Master Code to the Master Keypad

NEW MASTER CODE #

d) Set the Master Keypad to exit from Programming Mode

* *

e) The Link-up in the system is done automatically

BEEP BEEP ----- From Keypad

f) Put the Jumper back to OFF

ON OFF

g) The system is in Split-decoded operation with the new Link-up Code

THE FUNCTION MODE JUMPER -- (AVAILABLE ON DA-2800 ONLY)

Three positions are available for the Function Mode Jumper. Position 1 is for Split-decoded Mode and the positions 2 &

3 are for Stand Alone Modes.

POSITION 1 – SPLIT-DECODER (MAINS LED LAMP FLASHING)

Position 1 is for Split-decoder mode. All the functions and the 3 output relay operation manners follow the programmed

settings in the Master keypad. All the functions of the decoder are programmable from the keypad unit. The DA-2800

system is controlled by the keypads and the remote control keys in the Split-decoded mode.

POSITION 2 – STAND ALONE MODE 1 – START / STOP FOR OUTPUT 1 (MAINS LED LAMP ON)

Position 2 is one of the settings for Stand Alone mode. All the three Output Relays are controlled by the RF Remote Key

with the following functions:

Output 1 – Start / Stop – Controlled by Channel 1 of the RF remote key. Press the Button A once to start and press the

button once again to stop.

Output 2 – Start / Stop – Controlled by Channel 2 of the RF remote key. Press the Button B once to start and press the

button once again to stop.

Output 3 – Manual Momentary – Controlled by Channel 3 of the RF remote key. The output relay operates (Starts) as

long as the Button C is pressed and it stops when the button is released.

POSITION 3 – STAND ALONE MODE 2 – ADJUSTABLE TIMER FOR OUTPUT 1 (MAINS LED LAMP ON)

Position 3 is one of the settings for Stand Alone mode. All the three Output Relays are controlled by the RF Remote Key

with the following functions:

Output 1 – Adjustable Timer – Controlled by Channel 1 of the RF remote key. Press the Button A once to start the timer

and it resets automatically after time out. It is adjustable 1-30 seconds. It is convenient for

setting the time for door strike. Turn the timer clockwise for maximum time. See Figure 2.

Output 2 – Start / Stop – Controlled by Channel 2 of the RF remote key. Press the Button B once to start and press the

button once again to stop.

Output 3 – Manual Momentary – Controlled by Channel 3 of the RF remote key. The output relay operates (Starts) as

long as the Button C on the remote key is pressed and it stops when the button is released.

ENTRY MODES VALIDATIONLOCATION

1 or 270 #

USER PIN ENTRY MODE – Auto or Manual (Location 70)

USER PIN ENTRY MODES

Two modes 1 and 2 are available for User PIN entry options. The EM Card is always in Auto Entry Mode and is not

affected by the selection here.

1 --- Auto Entry Mode

Auto Entry Mode requires no pressing of the # key following the User PIN for code checking.

In the Auto Entry Mode, the User PINs MUST be set in the same digit length of the Master Code (For example, if

the Master Code is 5 digits, then all User PINs must be in 5 digits as well. All other User PINs not in 5 digits become

invalid). When the number of digits reaches, the system will check the User PIN automatically. Good for high traffic

access control.

2 --- Manual Entry Mode – (Default)

Manual Entry Mode always requires the # key following of the User PIN for code checking. The User PINs can be 4-8

digits arbitrary and they are NOT required to be in the same digit length of the Master Code. Manual Entry increases

the level of security in the code trial by the unauthorized people.

PACIFIER TONES ON-OFF SELECTION (Location 71)

PACIFIER TONES ON-OFF MODES

The Pacifier Tone is the Beep Tones from the keypad, which include the tones of Successful Key entry (1 beep), the

Output Operation Announcer (2 beeps or 1 long beep) and the Unsuccessful User Code/Card entry (5 beeps).

NOTE :

The beeps for the Warning and the Power-up Delay do not belong to pacifier tones and can not be set to OFF.

1 --- Pacifier Tone ON – (Default)

All the Pacifier Tones available from the keypad are enabled. They are the response tones indicating the operation

status of the keypad after the Card/User Code is entered.

0 --- Pacifier Tone OFF

All the Pacifier Tones are OFF. Good for place needs for a silent environment.

OUTPUT OPERATION ANNOUNCER (Location 72)

OUTPUT OPERATION ANNOUNCER

The announcer gives notification beep to the users and the visitors on the operation status of the outputs. There are

two notification modes available for the selection.The notification is also OFF while the Pacifier Tone OFF mode in the

Location 71 is selected.

1 --- 1 Second Long Notification -- (Default)

1 second notification beep is given when the output relay is activated with a valid Card/Code or Egress Button. It is

prepared to notify the person outside the door when the lock is released and the door can be opened. It is good for

the door lock device gives no sound when it activates, such as a magnetic lock.

0 --- 2 Short Beeps Notification

2 short beeps notification is given when the output is activated with a valid Card/Code.

FUNCTION MODES VALIDATIONLOCATION

1 or 0

INDIVIDUAL

CONNECTION TERMINALS

NOTE:

DRY CONTACT

A dry contact means that no electricity is connected to it. It is prepared for free connections.

N.C.

Normally Closed, the contact is closed circuit at normal state. It is open circuit when active.

N.O.

Normally Open, the contact is open circuit at normal state. It is closed circuit when active.

TRANSISTOR OPEN COLLECTOR OUTPUT

An open collector output is equivalent to a Normally Open (N.O.) contact referring to ground similar to a relay

contact referring to ground. The transistor is normally OFF, and its output switches to ground (

) when active. The

open collector can only provide switching function for small power but it is usually good enough for controlling of

an alarm system. The maximum rating is 24V DC/100mA Sink

OPEN COLLECTOR

OUTPUT ----

Output switches to

ground when activated

N.O. CONTACT

OUTPUT ----

Output switches to

ground when activated

EQUIVALENT

ALARM O/P

KEY ACT O/P

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

TAMPER

GND(

)

DOOR SENS

O/P 1 INHIB

INT. LOCK

DU OUT

DOOR BELL IN

EG IN

DATA I/O

KEYPAD PWR

GND(

)

12-24V DC

OPEN COLLECTOR OUTPUT

1A RELAY DRY CONTACTS

FOR AUXILIARY CONTROL

1A RELAY DRY CONTACTS

FOR AUXILIARY CONTROL

5A RELAY DRY CONTACTS

FOR DOOR STRIKE

OPEN COLLECTOR OUTPUT

INPUT/OUTPUT FOR SPLIT-DECODED SIGNALS

POWER OUTPUT FOR KEYPADS

COMMON GROUND

POWER INPUT FOR SYSTEM

N.C. SW

COMMON GROUND

N.C. SW

N.O. SW

OUTPUT 1O UTPUT 2O UTPUT 3

CONFIGURATION OF THE OUTPUT MODES OF OUTPUT 1, 2 AND 3 (Locations 51, 52 & 53)

The three relay outputs of this keypad are programmable for Start/Stop or Timing modes. Apart from the door access

control, alarm arm-disarm control, they are also universal timers for automatic operators in industry with their

99,999 seconds (over 24 hours) programmable timer.

OUTPUT LOCATIONS

51 -- Location for Output 1

52 -- Location for Output 2

53 -- Location for Output 3

OUTPUT MODE & TIMING

0 – Start /Stop Mode (Toggle)

The number 0 sets the output to the Start / Stop mode. The output Starts when an User PIN and/or Card is entered/

read; the output Stops when an User PIN and/or Card is entered/read again.

99999 Seconds Momentary --- (Default -- Momentary 5 Seconds)

The output can be set in Momentary Mode with the time of 1 second to 99,999 seconds. The output will reset

automatically when the time expires OR it can be RESET manually at anytime with the Super User Code that

operates the desired output before the end of the time.

Example : Reset Output 1 -- # 1 ------------- Output 1 resets

Reset Output 2 -- # 2 ------------- Output 2 resets

Reset Output 3 -- # 3 ------------- Output 3 resets

PERSONAL SAFETY AND SYSTEM LOCK-OUT (Location 60)

SAFETY & LOCK-OUT OPTIONS

The Options are represented by their Mode Numbers in programming. They are described below:

1 --- After 10 successive false Card/User Code trials, the keypad locks during 60 seconds. -- (Default)

2 --- After 10 successive false Card/User Code trials, activates the Duress output to switch to (

) ground.

The Duress Output can be released with any user PIN or Card in the User Group 1 or Super User PIN.

10 --- Selection of after 5 to 10 successive Card/User Code trials, the keypad locks during 15 minutes.

The keypad can be reset to release the lock-out with the “Super User Code” in the following way.

Example : Release the lock-out -- # 9

00 --- Disappearance of all the above lock-out securities.

SUPER USER CODE

1 to 2 Digits

LOCK-OUT MODES VALIDATIONLOCATION

60 #

SUPER USER CODE

OUTPUT MODE & TIME VALIDATIONLOCATIONS

53 0 or 1

99999 #

MASTER

INDIVIDUAL

This manual suits for next models

Table of contents

Other Velleman IP Access Controllers manuals

Velleman

Velleman HAA87A User manual

Velleman

Velleman HAA85BL User manual

Velleman

Velleman HAA2801 User manual

Popular IP Access Controllers manuals by other brands

Ava

Ava bqt miPASS BT510 installation guide

ZKTeco

ZKTeco SpeedFace-V5L user manual

2N Access Unit Configuration manual

Kedacom

Kedacom KSCA120 Series quick start guide

H3C

H3C WX2880X installation guide

G4S

G4S S870-EX Installation and user instructions

PRASTEL

PRASTEL M2000PE manual

Allegion

Allegion interflex IF-281 Cylinder manual

TECOM

TECOM TS1067E manual

Fermax

Fermax Memokey 100C Installer manual

Fermax

Fermax CITYLINE MEMOKEY User& installer's manual

Civintec

Civintec CV9601T-T-1F installation manual

BioMax

BioMax N-X90W user manual

ZKTeco

ZKTeco OP-200 quick start guide

FingerTec

FingerTec s-Kadex user guide

H3C

H3C WX5002ACCESSCONTROLLER installation manual

Conrad Electronic

Conrad Electronic KeyMatic CAC operating instructions

IDTECK

IDTECK Star 100R manual

Velleman DK-2800 User manual

Popular IP Access Controllers manuals by other brands