Velleman CAMIP16 User manual

CAMIP16
2 MP SOLID LIGHT IR VARIFOCAL BULLET IP CAMERA
CYLINDRISCHE IP-INFRAROODCAMERA MET
VARIFOCALLENS EN SOLID LIGHT-FUNCTIE (2MP)
CAMÉRA IP CYLINDRIQUE INFRAROUGE AVEC OBJECTIF
VARIFOCAL ET FONCTION SOLID LIGHT (2 MP)
CÁMARA IP CILÍNDRICA CON LENTE VARIFOCAL Y
FUNCIÓN SOLID LIGHT (2MP)
ZYLINDRISCHE IP-KAMERA MIT VARIFOKALLINSE UND
SOLID LIGHT-FUNKTION (2MP)
QUICK INSTALLATION GUIDE 5
KORTE HANDLEIDING 20
GUIDE D'INSTALLATION RAPIDE 35
GUÍA RÁPIDA 51
SCHNELLEINSTIEG 67

CAMIP16
V. 02 –10/12/2014 2 ©Velleman nv

CAMIP16
V. 02 –10/12/2014 3 ©Velleman nv
X
Y

CAMIP16
V. 02 –10/12/2014 4 ©Velleman nv
Z
28a
28b
28c

CAMIP16
V. 02 –10/12/2014 5 ©Velleman nv
QUICK INSTALLATION GUIDE
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of
the device after its lifecycle could harm the environment. Do not
dispose of the unit (or batteries) as unsorted municipal waste; it
should be taken to a specialized company for recycling. This device
should be returned to your distributor or to a local recycling
service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, do
not install or use it and contact your dealer.
2. Safety Instructions
Keep this device away from children and unauthorized users.
Risk of electroshock when opening the cover. Touching live wires
can cause life-threatening electroshocks. Do not disassemble or
open the housing yourself. Have the device repaired by qualified
personnel.
There are no user-serviceable parts inside the device. Refer to an
authorized dealer for service and/or spare parts.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages
of this manual.
Keep this device away from dust and extreme heat.
Protect this device from shocks and abuse. Avoid brute force when
operating the device.
Familiarise yourself with the functions of the device before actually
using it.
All modifications of the device are forbidden for safety reasons.
Only use the device for its intended purpose. Using the device in an
unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not
covered by the warranty and the dealer will not accept responsibility for
any ensuing defects or problems.

CAMIP16
V. 02 –10/12/2014 6 ©Velleman nv
DO NOT use this product to violate privacy laws or perform other illegal
activities.
4. Overview
Refer to the illustrations on page 2 of this manual.
1
lens
16
PC
2
sun shield
17
non-PoE router/hub
3
vandal-proof bracket
18
8P8C network cable
4
bracket screw holes
19
PoE injector
5
camera front cover
20
8P8C network cable
6
focal length screw
21
power
7
focus screw
22
NVR
8
desiccant
23
LAN SWITCH connector
9
sun shield installation
24
8P8C network cable
10
microSD card
25
router/hub
11
PC
26
8P8C network cable
12
PoE router/hub
27
cameras
13
8P8C network cable
28a
horizontal adjustment
14
8P8C network cable
28b
vertical adjustment
15
power
28c
rotational adjustment
5. Installation
1. Choose a location for the camera, keeping following guidelines in mind:
oDo not install the camera in locations where extremely high or low
temperatures or excessive vibrations may occur.
oAvoid mounting the camera near high electro-magnetic fields.
oDo not aim the camera at the sun or other extremely bright objects
or reflections (e.g. metal doors).
2. Use the mounting bracket [3] to determine the location of the
mounting holes. Drill the holes and secure the bracket using
3 screws [4].
3. Point the camera towards the field of interest [28a, 28b, 28c].

CAMIP16
V. 02 –10/12/2014 7 ©Velleman nv
6. Focal Length Selection and Focus
Adjustment
Notes:
We recommend adjusting the focal length and focus at an ambient
temperature between 0 and 40 °C.
Finish the adjustment as quickly as possible (max. 10 minutes) to
prevent that excess humidity builds up inside the camera, and the
desiccant absorbs too much moisture and is unable to keep the camera
dry.
Avoid adjusting in a high moisture environment. If this is not possible,
then finish the adjustment as quickly as possible.
To adjust focal length and focus, proceed as follows:
1. Open the front cover [5] of the camera by rotating it counter-clockwise.
Inside the camera, you see two handles to adjust the focal length [6]
and focus [7].
2. Loosen the screw of the handle, rotate to adjust, then tighten the screw
again.
3. Find the fresh desiccant (incl.) and place it in the camera as shown in
the illustration [8].
4. Immediately place back the front cover of the camera and turn it clock-
wise to fasten it.
Note: Make sure the front cover is fastened well to prevent moisture
from entering the camera.
5. Slide the sun shield over the camera [9].
7. Installing the microSD Card
Caution:
The data on the microSD card will be deleted after inserting the card
into the camera.
The camera does not support hot swapping. Insert or remove the card
with the power disconnected.
Insert the card into the camera as shown in the illustration [10]. It is
recommended to use tweezers for inserting or removing the card.
8. Connections
Cable Overview
Refer to the illustrations on page 3 of this manual.
a
8P8C network cable: to connect the camera to the router/hub. For PoE
installation, use only CAT.5e or CAT.6 cables, according to the
IEEE802.3af standard.

CAMIP16
V. 02 –10/12/2014 8 ©Velleman nv
b
alarm in (yellow): for external alarm connection
c
GND (brown): ground wire
d
RESET (red): remove the insulation from the wire, and twist it together
with a ground wire to reset the camera to the default settings.
e
GND (black): ground wire
f
alarm out (pink): for external alarm connection
g
power cable
Power Supply using PoE (Power over Ethernet)
The camera features PoE (Power over Ethernet). If your router or hub
supports PoE, you do not need to connect the camera to a power socket.
You can then connect the camera as shown in illustration [X]:
1. Use a network cable [14]to connect your camera to a PoE port of your
router/hub [12].
2. Make sure your router/hub is connected to a power socket [15].
If your router/hub does not support PoE, you can use a PoE injector (not
included) to use the PoE feature. You can then connect the camera as
shown in illustration [Y].
For connecting to a network video recorder (NVR), refer to illustration [Z].
9. Configuration with PC
1. For advanced camera configuration, make sure that your camera is
connected to a PC via the network. Refer to illustrations [X] and [Y].
2. Download and install the “IPscan.exe” program. You can download the
program from:
http://www.surveillance-download.com/user/IPscan.zip
3. Run the program to scan for available devices.
4. Set your PC in the same network segment as the camera that you want
to configure. Example: 192.168.2.xxx (where xxx = 0-255).
5. Note down the IP address and port number of the camera. In this
example, the IP address is 192.168.2.1 and the port number is 88.

CAMIP16
V. 02 –10/12/2014 9 ©Velleman nv
6. Open Internet Explorer on the PC, and enter the IP address and port
number in the URL box to access the camera in the following format:
http://ipaddress:portnumber
Example:
http://192.168.2.1:88
7. For details on the configuration of your camera, refer to the full user
manual on the CD-ROM.
10. Configuration with EagleEyes Mobile App
The installation method below describes the setup with an iPhone®with a
D-Link®wireless router and modem. The installation procedure is similar for
iPad®or Android™ devices. Refer to the full manual on the included CD-ROM
for more information.
10.1 Prerequisites
Before proceeding, check the following:
We recommend that you use your own ADSL or cable internet service
for easy network configuration.
Your camera is connected to your wireless router with an 8P8C network
cable, and it is powered on.
EagleEyes-Lite or EagleEyes-Plus is installed on your device.
If not, download it from your device’s app store.
Note: EagleEyes HD for iPad does not support network configuration.
Please install EagleEyes-Lite or EagleEyes Plus on your iPad instead.
10.2 Preparing the Network Configuration
1. Connect your camera to your wireless router using an 8P8C network
cable (see “Overview” above).
2. Write down the IP address of your wireless router. You will need it
later. To find the IP address, proceed as follows:
3. Connect your mobile device to the wireless router that has the camera
connected.
4. Go to Settings > WiFi.
5. Press the “>” button to see the details of the selected wireless network.
The IP address is visible next to “Router”.
(In the sample screen, the IP address is 192.168.2.1)

CAMIP16
V. 02 –10/12/2014 10 ©Velleman nv
10.3 Adding Your Camera to the EagleEyes App
1. Establish a wireless connection between your mobile device and the
wireless router that has the camera connected.
2. Open the EagleEyes app and click the “+” button to add a new device.
3. Select “Local Network Search” to search for the camera.
The device will show a list
of devices on the network.
The displayed IP address is
the address that your
router assigned to your
camera.
4. Select the camera from the list. The settings page appears.
5. Change the port number of the camera as needed. The default port
number is 88. If port number 88 is blocked, you can change it to any
value between 1-9999 (for example 8080).
6. Write down the IP address and the port number of the camera. You
will need them later.
(In the sample screens below [A], the IP address is 192.168.2.197 and
the port number is 88.)
7. Press “Apply” to confirm your settings.

CAMIP16
V. 02 –10/12/2014 11 ©Velleman nv
8. Wait until “Status” [B] indicates “Done” or “Fail”.
oIf the status shows “Done”, the device page appears again. Proceed
with the next step.
oIf the status shows “Fail”, press the button on the top right side
of your device. In the popup window, select “DDNS”. The device page
appears again. Proceed with the next step.
9. In “Title” [C], enter a meaningful name for your camera connection and
press “Save” to confirm.
A
B
C
10.4 Port Forwarding
At this moment, you can only access the camera when connected to your
own wireless network, not through the internet. This is because a home
network is usually connected to the internet through a router. Only the
router’s external IP address (assigned to you by your Internet Service
Provider) can be seen on the internet. Moreover, the router will also block
access to any device in your home network, including your camera. To
bypass this, most routers support a mechanism called port forwarding
that allows access from the internet to a device in the home network.
You can set up port forwarding as follows:
1. Open your web browser on your mobile device, and enter the
IP address of your router you wrote down in the address bar.
Your router configuration page appears.
2. Go to the port forwarding (or virtual server) rule configuration page.
Note: The naming of port forwarding or virtual server may vary based
on the brand of your router. Refer to the user manual of your specific
router for more information.

CAMIP16
V. 02 –10/12/2014 12 ©Velleman nv
The example below shows the screen for a D-Link router: select the
“Advanced” tab and then choose “Port Forwarding”.
3. Enter the camera IP address and port number that you noted down and
enable this rule. You can now access your camera through the internet.
4. If your wireless router supports UPnP (Universal Plug and Play), make
sure the function is enabled. UPnP enhances communication between
the router and wireless devices. If necessary, refer to the manual of the
router software.
10.5 Checking the Connection
When you have completed network setup and port forwarding, check your
connection setup as follows:
1. On your mobile device, switch your network mode to 3G or connect to a
different wireless network than the one that has your camera
connected.
2. Start EagleEyes and select the camera you just added to see if you can
access it.
oIf yes, your network connection works. Proceed with “Changing the
Account User Name and Password”below.
oIf not, proceed with the following step.
3. Switch your network mode back to the wireless network that has your
camera connected.
4. Start EagleEyes, and add a new connection with the IP address and port
number that you set up in “Adding Your Camera to the EagleEyes
App”.
5. See if you can access the camera with this connection.
oIf yes, return to “Port Forwarding” to set up port forwarding again.
oIf not, return to step 4 of “Adding Your Camera to the EagleEyes
App” and reconfigure the connection.

CAMIP16
V. 02 –10/12/2014 13 ©Velleman nv
10.6 Changing the Account User Name and Password in EagleEyes
To ensure the safety of your camera connection, modify the default user
name and password as follows:
1. On your mobile device, access the camera in EagleEyes.
2. Press the Configuration button .
3. Select Advance Setup > Account.
4. Modify the default user name (admin) and password (admin) to the
ones you prefer.
11. EagleEyes Operation
Address Book
Live View & Control
Configuration
When you start EagleEyes, Address Book is displayed.
1
Info
Press for more information on how to use EagleEyes
2
Toolbar
Add, edit, and delete items from Address Book
3
Setting
Configure EagleEyes parameters
Select the camera connection in Address Book to enter Live View & Control.
4
Configuration
Press to enter the camera’s configuration page.
12. File Backup
You can backup recorder files:
with the Video Viewer software
with internet explorer 32 bits
using the SD card from the camera in the computer.

CAMIP16
V. 02 –10/12/2014 14 ©Velleman nv
12.1 Back up files with Video Viewer
1. Open the Video Viewer software.
If you do not have the Video Player software, you can download and
install it from the CAMIP16 product page on www.velleman.eu.
2. Select the appropriate camera in the address book and click Edit.
3. Under Config > Record:
oSet Enable to Yes.
oSet Overwrite to Yes.
oSet the record resolution to HD1080P.

CAMIP16
V. 02 –10/12/2014 15 ©Velleman nv
4. Under Trigger, set the motion detection, as shown:

CAMIP16
V. 02 –10/12/2014 16 ©Velleman nv
5. Click the Download button.
You can now copy the video files to your computer:
12.2 Back up files in Internet Explorer (32-bit only)
To use Internet Explorer to back up files, the following conditions have to be
met:
You have Internet Explorer 32 bits.
Java needs to be installed and up to date.
You need to activate the compatibility mode.
You need to set specific ActiveX security settings.

CAMIP16
V. 02 –10/12/2014 17 ©Velleman nv
1. To check whether you are using Internet Explorer 32 bit.
oIn Internet Explorer, open Help > About Internet Explorer.
You are using the 32-bit version if "64-bit version" is not shown
in the screen.
2. Activate browser compatibility:
oSelect Tools > Compatibility View.
3. Set a custom security level for ActiveX controls:
oOpen Internet Options > Security tab and click Custom level.
oSet the option "Download unsigned ActiveX controls" to "Prompt".
oClick OK.

CAMIP16
V. 02 –10/12/2014 18 ©Velleman nv
4. Access your camera in Internet Explorer (see above).
You can download the recorded files via the "Backup" button:
12.3 View files on an SD card
1. Remove the micro SD card from the camera and insert it in a
computer.
2. Open the Video Viewer software.
If you do not have the Video Player software, you can download and
install it from the CAMIP16 product page on www.velleman.eu.
3. Open the file NWCAM.EDB.

CAMIP16
V. 02 –10/12/2014 19 ©Velleman nv
In the event list, you can select the file you want to see:
For detailed information, please check the full manual on the included
CD-ROM.
The CAMIP16 IP camera is ONVIF certified: it is compatible with all major IP
camera brands which are ONVIF certified as well. For more information,
please refer to www.onvif.org.
Use this device with original accessories only. Velleman nv cannot
be held responsible in the event of damage or injury resulting from
(incorrect) use of this device.
For more info concerning this product and the latest version of this
manual, please visit our website www.velleman.eu.
The information in this manual is subject to change without prior
notice.
All registered trademarks and trade names are properties of their respective
owners and are used only for the clarification of the compatibility of our
products with the products of the different manufacturers.
iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and
other countries. D-Link, the D-Link logo are trademarks or registered
trademarks of D-Link Corporation or its subsidiaries in the United States and
other countries. Android is a trademark of Google Inc.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All
worldwide rights reserved. No part of this manual may be copied,
reproduced, translated or reduced to any electronic medium or otherwise
without the prior written consent of the copyright holder.

CAMIP16
V. 02 –10/12/2014 20 ©Velleman nv
KORTE HANDLEIDING
1. Inleiding
Aan alle ingezetenen van de Europese Unie
Belangrijke milieu-informatie betreffende dit product
Dit symbool op het toestel of de verpakking geeft aan dat, als het
na zijn levenscyclus wordt weggeworpen, dit toestel schade kan
toebrengen aan het milieu. Gooi dit toestel (en eventuele
batterijen) niet bij het gewone huishoudelijke afval; het moet bij
een gespecialiseerd bedrijf terechtkomen voor recyclage. U moet
dit toestel naar uw verdeler of naar een lokaal recyclagepunt
brengen. Respecteer de plaatselijke milieuwetgeving.
Hebt u vragen, contacteer dan de plaatselijke autoriteiten
betreffende de verwijdering.
Dank u voor uw aankoop! Lees deze handleiding grondig voor u het toestel
in gebruik neemt. Werd het toestel beschadigd tijdens het transport,
installeer of gebruik het dan niet en raadpleeg uw dealer.
2. Veiligheidsinstructies
Houd dit toestel buiten het bereik van kinderen en onbevoegden.
Elektrocutiegevaar bij het openen van het toestel. Raak geen
kabels aan die onder stroom staan om dodelijke elektrische
schokken te vermijden. Open de behuizing niet zelf. Laat het
onderhoud van het toestel over aan een geschoolde vakman.
De gebruiker mag geen onderdelen vervangen. Voor onderhoud
en/of reserveonderdelen, contacteer uw dealer.
3. Algemene richtlijnen
Raadpleeg de Velleman® service- en kwaliteitsgarantie achteraan deze
handleiding.
Bescherm dit toestel tegen stof en extreme hitte.
Bescherm het toestel tegen schokken. Vermijd brute kracht tijdens de
bediening van het toestel.
Leer eerst de functies van het toestel kennen voor u het gaat
gebruiken.
Om veiligheidsredenen mag u geen wijzigingen aanbrengen aan het
toestel.
Gebruik het toestel enkel waarvoor het gemaakt is. Bij onoordeelkundig
gebruik vervalt de garantie.