Venset TS700B User manual

Electric TV Lift, TS700B & TS1000B
1
INSTALLATION INSTRUCTIONS
CONTENT:
1. Important safety instructions.
2. Specifications and main dimensions.
3. Parts included.
4. Installation.
5. Adjusting the stroke length of the lift.
6. Declarations of conformity.
WARNING
WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL
ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS
AND WARNINGS REGARDING THE USE OF THIS PROD-
UCT MAY RESULT IN SERIOUS BODILY INJURY.
No. #323700.2
TS1000B
TS700B

Electric TV Lift, TS700B & TS1000B
2
1. Important safety Instructions.
Use the following safety guidelines to help protect your lift from potential damage and to en-
sure your own personal safety.
Read all the installation instructions before testing or installing your lift.
Read and follow all safety instructions.
Keep manual rocker switch out of reach of children.
To prevent bodily injury keep hands and clothing away from the lift while the lift is in
operation.
Before installing the lift or working with its connections, unplug the lift from the elec-
tricity main supply.
Do not install the lift or power supply in places subject to high temperatures for exam-
ple near a radiator, or heating vent.
The TV lift must only be mounted in a dry area and it must be ensured before use that
the lift is safe or protected from liquid contact or spillage.
To avoid damaging the power supply and power cord, do not put anything on it or
place it where it could become damaged.
Unplug the lift in the following conditions:
When the power cord or plug is damaged or frayed.
If the lift or power supply has been exposed to rain or water or any liq-
uid contamination whatever.
If the lift exhibits a distinct change in performance, indicating a need
for attention.
MANUFACTURES who build this lift into other products or use it with other products,
MUST make sure to prevent bodily injury. The MANUFACTURER of the final product
is responsible to give the end user proper warnings and instructions for use.
CAUTION: Before you begin any of the Installation procedures (4. Installation.),
read and follow the warnings and safety instructions on this page.
WARNING ! THIS IS NOT A TOY !
WARNING ! CHILDREN SHOULD NOT OPERATE LIFT !

Electric TV Lift, TS700B & TS1000B
3
2. Specifications and main dimensions.
Materials and weights: Steel, black powder coated - Weight ~ 15/21 kg
Max. working loads:
45 kg (by standard installation)
29 kg (when lift is mounted upside down)
50 kg peak load
Duty cycle: 10% by 50% of working load or max 2 min. continuously
Operation: Rocker switch
Voltage:
Standby Consumption:
100-240 VAC / 50/60Hz
< 1 Watt
Main dimensions, TS700B [mm]:
VESA, TS700B:
200x200, 200x100

Electric TV Lift, TS700B & TS1000B
4
Main dimensions, TS1000B [mm]:
VESA, TS1000B:
200x200, 200x100

Electric TV Lift, TS700B & TS1000B
5
3. Parts included.
Lift unit ( #1 )
Lid lifter ( #2 )
Power supply ( #3 )
AC input wire, country configured ( #4 )
Adaptor wire ( #5 )
Rocker switch ( #6 )
Power supply bracket ( #7 )
Lift unit ( #1 )
Lid lifter ( #2 )
AC input wire, coun-
try configured ( #4 )
Power supply
( #3 ) Rocker switch
( #6 )
Power supply mount-
ing bracket ( #7 )
Adaptor wire
( #5 )

Electric TV Lift, TS700B & TS1000B
6
4. Installation.
1) Remove all contents from packaging and compare with parts list.
2) Place the lift unit (#1) on e.g. the back panel of the cabinet* in a location that will al-
low full up and down movement of the lift.
3) Fasten the unit securely to the cabinet. Screws must be appropriate for the material
being used.
4) Connect the plug from lift unit (#1) to the adaptor wire (#5), rocker switch (#6) and the
power supply (#3) like shown below.
5) Mount rocker switch (#6) in an easy location by cutting a ø30 hole and pressing the
switch into place. Secure excess wire to keep away from moving parts.
6) Plug the power cord into main electrics and operate manual rocker switch See trou-
bleshooting guide on www.venset.com, click “support”.
Helpful hint: Mount TV lift and electronics to plywood panel and attach to inside back of cab-
inet using appropriate number of screws. This allows all components to be removed from the
cabinet if necessary. If this is not possible, create an access panel to the electronics.
** Aim to create easy access for wear and tear replacement stroke service.

Electric TV Lift, TS700B & TS1000B
7
5. Adjusting the stroke length of the lift.
Adjusting the bottom stop:
The bottom stop can be adjusted to any preferred height, e.g. if you don’t want the lift to go
all the way down into the cabinet. You can adjust just one or both end stops.
1. The more you move the glider down the cable
the earlier the lift will stop on the down stroke
as the end stop switch will be triggered sooner.
2. Raise the lift up to the just above lowest posi-
tion that you want it to reach on the down
stoke.
3. Remove the small plastic cover plate (see fig.1)
and you will see the glider on the cable.
4. Use a 2.5mm Allen key to loosen the screw in-
side the glider. (see fig.1)
5. Move the glider down the cable accordingly and
tighten the screw securely.
6. Replace the plastic cover plate, the glider will
no longer be in this window.
7. Test the lift fully up and down and check the
desired bottom stop position is as you require.
Fig. 1

Electric TV Lift, TS700B & TS1000B
8
Adjusting the top stop:
The top stop can be adjusted to any preferred height, e.g. if you don’t want the lift to go all
the way up out of the cabinet. You can adjust just one or both end stops.
1. The more you move the glider down the cable
the earlier the lift will stop on the up stroke as
the end stop switch will be triggered sooner.
2. Raise the lift up to full height.
3. You will see the glider on the cable below the
nylon brushes (see fig.2)
4. Use a 2.5mm Allen key to loosen the screw in-
side the glider. (see fig.2)
5. Move the glider down the cable accordingly and
tighten the screw securely.
6. Test the lift fully up and down and check the
desired top stop position is as you require.
Fig. 2

Electric TV Lift, TS700B & TS1000B
9
6. Declarations of conformity.

Electric TV Lift, TS700B & TS1000B
10
The information in this document is subject to change without notice.

Mounting instruction, VESA 300x300 / 400x300 / 400x400
328880.0