Vents Lumis 100 User manual

USER’S MANUAL
AXIAL FAN WITH INTEGRATED LIGHT SOURCE
Lumis 100
V01-LUMIS-01_EN.indd 1 17.08.2015 11:09:14
mepokerkft.hu

2
CONTENTS
Safety requirements 3
Purpose 5
Delivery set 5
Designation key 5
Technical data 6
Unit design and operating principle 6
Mounting and set-up 7
Technical maintenance 9
Transportation and storage regulations 10
Manufacturer's warranty 10
Acceptance certificate 12
Seller information 12
Installation certificate 13
Warranty card 13
V01-LUMIS-01_EN.indd 2 17.08.2015 11:09:14
mepokerkft.hu

3
This user’s manual consisting of the technical details, operating instructions and technical
specication covers the installation and mounting of the Lumis 100 axial fan with integrated
light source (hereinafter referred to as «the fan» or «the unit» as mentioned in the «Safety
requirements» and «Manufacturer’s warranty» sections as well as in warnings and information
blocks).
SAFETY REQUIREMENTS
Read the user’s manual carefully prior to installing and operating the unit.
Fulfil the user’s manual requirements as well as the provisions of all the applicable
local and national construction, electrical and technical norms and standards.
The warnings contained in the user’s manual must be considered most seriously
since they contain vital personal safety information.
Failure to follow the rules and safety precautions noted in this user’s manual may
result in an injury or unit damage.
After a careful reading of the manual, keep it for the entire service life of the unit.
While transferring the unit control the User’s manual must be turned over to the
receiving operator.
Symbol legend:
WARNING!
DO NOT!
UNIT MOUNTING AND OPERATION SAFETY PRECAUTIONS
• Disconnect the unit from power
mains prior to any installation
operations.
• Unpack the unit with care.
• Do not lay the power cable of the
unit in close proximity to heating
equipment.
• While installing the unit follow
the safety regulations specific to
the use of electric tools.
• Do not lay the power cable of the
unit in close proximity to heating
equipment.
• Do not operate the unit outside
the temperature range stated
in the user's manual as well
as in aggressive or explosive
environments.
V01-LUMIS-01_EN.indd 3 17.08.2015 11:09:15
mepokerkft.hu

4
• Do not use damaged equipment
or cables when connecting the
unit to power mains.
• Disconnect the unit from power
supply prior to any technical
maintenance.
• Do not touch the unit controls
with wet hands. Do not carry out
the installation and maintenance
operations with wet hands.
• Do not wash the unit with water.
Protect the electric parts of the
unit against ingress of water.
• Do not allow children to operate
the unit.
• Use the unit only for its intended
purpose.
• Do not store any explosive or
highly flammable substances in
close proximity to the unit.
• When the unit generates
unusual sounds, odour or emits
smoke disconnect it from power
supply and contact the Seller.
• Do not open the unit during
operation.
• Do not direct the air flow
produced by the unit towards
open flame or ignition sources.
• Do not block the air duct when
the unit is switched on.
• In case of continuous operation
of the unit periodically check
the security of mounting.
V01-LUMIS-01_EN.indd 4 17.08.2015 11:09:15
mepokerkft.hu

5
PURPOSE
The unit described herein is the exhaust axial fan designed for exhaust ventilation and for
lighting of small and medium sized residential premises. The fan is designed for use in Ø100
mm air ducts. The fan can be equipped with a back valve to prevent air back drafting when the
fan is switched off.
THE UNIT MAY NOT BE OPERATED BY CHILDREN OR
PERSONS WITH REDUCED PHYSICAL, MENTAL OR SENSORY
CAPACITIES, OR LACKING THE APPROPRIATE TRAINING.
THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY
PROPERLY QUALIFIED PERSONNEL AFTER THE APPROPRIATE
BRIEFING. THE CHOICE OF UNIT INSTALLATION LOCATION MUST
PREVENT UNAUTHORIZED ACCESS BY UNATTENDED CHILDREN.
DELIVERY SET
Fan 1 item
User's manual 1 item
Power supply unit 1 item
Fastening kit 1 item
Packing 1 item
DESIGNATION KEY
Lumis 100 K L turbo
Fan series
Exhaust spigot diameter [mm]
100
Non-return valve
Ball bearings
Increased capacity
V01-LUMIS-01_EN.indd 5 17.08.2015 11:09:15
mepokerkft.hu

6
TECHNICAL DATA
The fan is designed for indoor application and for connection to single-phase AC 220-240 V
/ 50(60) Hz power mains at the ambient temperature ranging from +1°C up to +45°C.
Ingress protection rating - IP 24.
The fan requires no grounding.
Connected air duct diameter Ø100 mm.
The unit design is constantly being improved, so some models can slightly differ from those
ones described in this manual.
Ø
178 Ø118
Ø 99,4
133,5
46
DESIGN AND OPERATING PRINCIPLE
The casing and the impeller are made of high-quality durable ABS plastic, UV resistant.
The 10 watt LED backlight lamp is integrated in the fan casing.
The impeller design enhances the fan efficiency and prolongs the motor service life.
The fan is equipped with an energy-efficient motor with overheating protection. The
maintenance-free motor is designed for continuous operation.
Modifications and options:
• Lumis 100 K - the fan is equipped with a back valve to prevent air back drafting (at
customer’s request).
• Lumis 100 L - the motor is equipped with ball bearings for longer service life (appr. 40
thousand hours) and fan mounting at any angle. The bearings are maintenance-free
and contain enough grease for the entire operating period.
• Lumis 100 turbo - high-powered motor.
V01-LUMIS-01_EN.indd 6 17.08.2015 11:09:15
mepokerkft.hu

7
MOUNTING AND SET-UP
The ventilator is designed for ceiling mounting. The fan is mounted directly into the
ventilation shaft. Flexible duct connection is recommended in case of the remote ventilation
shaft location. The air duct is connected to the fan exhaust flange through a clamp.
Fan mounting and connection.
1 2 3
QF
L N
Ø 100 mm
Install the air duct. Route the wires
and prepare a Ø100 mm hole.
Make a hole in the fan casing
for routing the power wires.
V01-LUMIS-01_EN.indd 7 17.08.2015 11:09:15
mepokerkft.hu

8
45
6
7
8
X1
L (~) SN (~)
Power supply unit
black red
brown blue
+ -
N L
X1
S
ON
OFF
L (~) S1
S2
N (~)
Power supply unit
black red
blue
brown
+
-
N L
X1
S1 S2
ON
OFF
ON
OFF
Simultaneous
switching on
of the fan
and the lamp.
Separate
switching on
of the fan
and the lamp.
Connect the wires according to the Wiring diagram.
Connect the power supply unit
and install it in a false ceiling.
Route the wires though the
hole in the casing and install
the fan in the air duct.
Fix the fan on the ceiling surface
using the screws.
Connect the connectors and install
the lamp on the fan casing by turning
it clockwise.
V01-LUMIS-01_EN.indd 8 17.08.2015 11:09:16
mepokerkft.hu

9
TECHNICAL MAINTENANCE
QF
L N
1 2
3 4
5 6
V01-LUMIS-01_EN.indd 9 17.08.2015 11:09:16
mepokerkft.hu

10
TRANSPORTATION AND STORAGE REGULATIONS
Store the unit in the manufacturer’s original packing box in a dry closed ventilated premise
with temperature range from +5 °C to + 40 °C.
Storage environment must not contain aggressive vapours and chemical mixtures provoking
corrosion, insulation and sealing deformation.
Use hoist machinery for handling and transportation to prevent possible mechanical
damages of the unit.
Follow the applicable moving regulations specific to the particular cargo type while loading
and unloading.
The unit can be carried in the original packing by any mode of transport provided proper
protection against precipitation and mechanical damage.
Avoid sharp blows, scratches or rough handling during loading and unloading.
MANUFACTURER’S WARRANTY
The manufacturer hereby warrants normal operation of the unit for 60 months after the retail
sale date provided the user’s observance of the transportation, storage, mounting and operation
regulations.
Should any malfunctions occur in the course of the unit operation through the Manufacturer’s
fault during the guaranteed period of operation the user is entitled to elimination of faults by the
manufacturer by means of warranty repair at the factory free of charge.
The warranty repair shall include work specific to elimination of faults in the unit operation
to ensure its intended use by the user within the guaranteed period of operation. The faults are
eliminated by means of replacement or repair of the unit components or a specific part of such
unit component.
The warranty repair does not include:
• routine technical maintenance
• unit installation / dismantling
• unit setup
To benefit from warranty repair the user must provide the unit, the user’s manual
with the purchase date stamp and the payment document certifying the purchase.
The unit model must comply with the one stated in the user’s manual.
Contact the Seller for warranty service.
V01-LUMIS-01_EN.indd 10 17.08.2015 11:09:16
mepokerkft.hu