Vents VCN 100 User manual

USER'S MANUAL
2012
VCN

2
USE
BASIC
TECHNICAL
CHARACTERISTICS
The centrifugal fans VCN series are designed for extract ventilation of living spaces,
offices, shops, garages, kitchens, bathrooms and other residential and public
premises.
The fans are designed for top installation at ventilation shaft outlets.
The fans are rated for continuous operation always connected to power mains.
Ingress protection rating according to access to hazardous parts and
water ingress  IPX4.
The minimum transported temperature is 15°C. The fan is suitable for shortterm
air transportation with the temperature reaching 30°C. The maximum transported
air temperature is
Transported medium must not contain any dust or other solid impurities,
sticky substances or fibrous materials.
The fan designations, overall and connecting dimensions, parameters are shown
in tables 1, 2, 3 and in fig. 1.
Due to constant improvements the design of some models may slightly differ from
those ones described in this manual.
FAN
DESIGNATION
KEY
VENTS VCN Х К
Air duct diameter [mm]
Modification with a backdraft damper
100, 125, 150, 160, 200
VCN

3
Designation key example
VENTS VCN 100
VENTS VCN 150 K
 centrifugal fan for mounting with 100 mm air duct.
 centrifugal fan with a backdraft damper for mounting with 150 mm
air duct.
Ø
Ø
1
Table 1
Fan
type
1  casing;
2  cover;
3  bracket;
4  bracket;
5  turbine;
6  selftapping screw;
7  capacitor;
8  terminal block;
9  spigot
(for VCN…K modification equipped
with a backdraft damper)
Weight,
kg
Dimensions, mm
DLBH
VCN /100 100 КVCN
VCN VCN125 125 К/
VCN VCN150 150 К/
VCN VCN160 160 К/
VCN VCN200 200 К/
100 355 260 140 3,60
125 355 260 140 3,60
150 400 300 140 4,70
160 400 300 140 4,70
200 400 300 140 4,70
VCN

4
Table 2
Fan
type
VCN /100
100 КVCN
VCN
VCN
125
125 К
/
VCN
VCN
150
150 К
/
VCN
VCN
160
160 К
/
VCN
VCN
200
200 К
/
1~ 230
V,
50 Hz WА
m/h
3R P M dB(A) 0CIP
1~ 230
1~ 230
1~ 230
1~ 230
71
75
96
95
96
0,31
0,33
0,42
0,41
0,42
325
(295*)
485
(450*)
630
(565*)
650
(590*)
700
(640*)
2530
2475
2400
2440
2515
54
54
58
60
62
55
55
55
55
55
IP X4
IP X4
IP X4
IP X4
IP X4
*  for the models with an integrated backdraft damper (VCN…K)
Table 3
1~ 230
1~ 230
1~ 230
1~ 230
1~ 230
92
98
100
96
97
0,40
0,43
0,44
0,42
0,42
350
(320*)
500
(465*)
650
(595*)
685
(625*)
710
(650*)
2625
2570
2270
2400
2555
54
54
58
60
62
55
55
55
55
55
IP X4
IP X4
IP X4
IP X4
IP X4
VCN
Fan
type
V,
60 Hz WА
m/h
3R P M dB(A) 0CIP
VCN /100
100 КVCN
VCN
VCN
125
125 К
/
VCN
VCN
150
150 К
/
VCN
VCN
160
160 К
/
VCN
VCN
200
200 К
/
*  for the models with an integrated backdraft damper (VCN…K)

5
The fan ingress Protection (IP) rating from solid objects and liquids IPX4 demands
extra protection against water ingress.
To protect the fan against water ingress mount a hood at the intake pipe or under the
roof.
Take steps to prevent ingress of smoke, carbon monoxide and other combustion
products into the room through open chimney flues or other fireprotection devices.
Mounting and maintenance of the fan are allowed only by duly qualified electricians in
compliance with valid rated norms.
Disconnect the fan from power mains prior to any servicing and repair works.
Before connecting the fan to power mains check the fan for any visible damages
of impeller and casing. The casing internals must be free of any foreign objects which
can damage the impeller blade.
Do not use the fan in explosive or firehazardous environment.
SAFETY
REQUIREMENTS
WARNING
!!
The fan (fig. 1) consists of the casing 1 with the cover 2 that is attached by the screws 6.
The clockwise rotation impeller 5, the capacitor 7 and the terminal block 8 are installed
inside the casing on the brackets 3 and 4 for connection to singlephase power mains.
The casing is equipped with an intake spigot for connection to air duct.
The fan is designed for top mounting (fig. 2).
FAN
STRUCTURE
INSTALLATION
AND MOUNTING
GUIDELINES
VCN

6
2
Disconnect the fan from power mains prior to any wireworks (fig. 3).
To install the fan on the wall remove the selftapping screws 6 and remove the cover 2
(fig. 4), drill the holes for dowels in compliance with mounting seats on the fan casing
(fig. 5,6,7) and install the fan with screws (fig. 8).
The power cable must be routed through the screwed cable gland.
3 4
VCN

7
5
7
6
8
VCN

8
CONNECTIO
TO POWER
MAINS
Connect the fan to singlephase power mains through the automatic circuit breaker
integrated into the fixed power mains. Cut power supply off prior to wireworks.
The contact gap on all poles must be at least 3 mm.
Connect the power cable to the terminal block 8 following the wiring diagram on the
bracket 3 (fig. 10, 11).
Put the cover 2 and tighten the selftapping screws 6 (fig. 12).
9
11
10
12
N
L
L
X
S1
~
blue
black
yellow-green
N
brown
The delivery set includes:
 fan  1 item;
 dowel and screw  4 items;
 user's manual  1 item;
 packing box  1 item.
DELIVERY
SET
VCN

9
Disconnect the fan from power mains prior to all maintenance operations.
Maintenance of the fans means periodic cleaning of the fan surfaces from dirt and
dust when the fan is switched off.
Use a soft cloth or compressed air to remove dust (fig. 13).
The impeller blades require thorough cleaning every 6 months.
The filter prevents the fan soiling and reduces the cleaning periodicity.
To clean the impeller blades follow the further procedure:
Clean the impeller blades with a cloth wetted in water and mild detergent solution.
Avoid liquid dripping on the motor! (fig. 14, 15).
After cleaning of the impeller reinstall the cover and tighten the screws.
Any servicing operations by a professional only!
MAINTENANCE
13
13
14
VCN

10
STORAGE
RULES
Store the fan in manufacturer's packaging in a ventilated room at temperatures
between +5°C and +40°C and relative humidity not more than 80% at +20°C.
The fan is not rated for operation in a medium containing acid or alkali vapours or
other aggressive admixtures.
MANUFACTURER'S
WARRANTY
We hereby declare that the following product complies with the essential protection
requirements of Electromagnetic Council Directive 2004/108/EC, 89/336/EEC and
Low Voltage Directive 2006/95/EC, 73/23/EEC and CEmarking Directive 93/68/EEC
on the approximation of the laws of the Member States relating to electromagnetic
compatibility. This certificate is issued following test carried out on samples of the
product referred to above.
While purchasing the product the customer accepts the following warranty terms:
Manufacturer hereby guarantees normal operation of the fan for 24 months from the
date of resale, subject to the compliance with transport, storage, mounting and
operation rules.
In case of no confirmation of sales date the warranty period is calculated from the
production date.
All the units and components belonging to the faulty unit and replaced within the
warranty period shall be covered by the previous warranty period and general warranty
conditions. Thus the warranty period is neither extended nor renewed for the replaced
components or the fan.
In case of any failures due to faulty manufacturing during warranty period, the Customer
has the right to have the goods replaced at the manufacturing facility.
Replacements are offered at Seller.
The accessories operated together with the unit, both included and not included into
the delivery list as well as other equipment operating jointly with the unit shall not be
covered by the warranty.
No warranty for compatibility of the fans with other producers' goods.
Only manufacturing defects are covered by the warranty terms.
VCN

11
All the defects and faults resulting from mechanical effect during operation process or
natural wearandtear shall not be covered by the warranty conditions.
The malfunctions caused by violence of operation, servicing and maintenance guidelines
either by Customer or third parties or caused by unauthorized design modifications shall
not be covered by warranty.
The manufacturer is not responsible for any mechanical or physical damages resulting
from the manual requirements violence, the unit misuse or gross mechanical effect.
The indirect damages such as reinstallation or reconnection of the unit, direct or indirect
losses etc. related to the unit replacement shall not be indemnified.
Mounting/dismantling, connection/disconnection and setup of the unit shall not be
covered by the warranty.
The contractor in charge for quality of mounting, electric mounting and adjustment works
shall be responsible for the warranty thereof. In any case the indemnity amount shall not
exceed the actually paid value for the defective unit price.
NO LIABILITY FOR THE RELATED DAMAGES:
VCN

ACCEPTANCE
CERTIFICATE
Centrifugal fan VENTS VCN __________""
The fan is recognized as serviceable.
Stamp of the acceptance inspector
Date of production
(name of the vendor, stamp of the shop)
Date of sale
V06 03EN
WARRANTY
CARD
VCN
12