Verity Audio MONSTER212 User manual

User's manual
www.verityaudio.fr

Acoustics
AES Power LF:1400W / HF 80W
Program Powe LF 2800W / HF 160W
Nominal impedance 4Ω
Frequency Range LF:48~2.3kHz
HF:900~20kHz(-10dB)
Frequency Response 55~18.5kHz
Sensitivity LF 100dB；HF 110dB(1W/m)
Maximum SPL ＞132dB/138dB
Coverage Angle
Horizon 110°
Vertical 80° (Up20°+Down60° )
Drivers
LF driver 2x 12" Neodymium driver (V.C:4")
HF driver 1x1.4" Neodymium driver(V.C:2.5")
Connector
5xNEUTRIK® NL4 SPEAKON
LF INPUT1±；LINK：2±
HF INPUT2±；
Cabinet
CNC 、tongue and groove cabinet、18mm birch wood
Environmental ivory white surface treatment
Hanging Accessories
4 pcs Ø40 hoisting ring for quickly mounting
Product dimension/Packing dimension
HF
LF W750xH549xD739mm / W910xH510xD780
N.W/G.W
HF 8.5kg/ 12kg
LF 39.5kg/ 51kg
: :
: : :
:
: (-10dB)
:
: : :
:
:
:
::
::
:Packing dimension W460xH430xD440
:
:
:
SPECIFICATIONS
739
613
750
364
549
742
Monster212 is a two way full range speaker that
combine by individual dual 12 inch LF speaker and one
2.5 inch HF compression driver with BI-AMP design . it
have own passive filer in the LF speaker and HF
speaker that it can driving by amplifier directly .
Monster series speaker is the perfect combination with
the science and acoustics .With excellent acoustic
phase and frequency response it can make you have a
good listening experience in high pressure level; it
have excellent performance in high frequency cause
the horizontal asymmetric design horn and the
impedance compensation circuit which stabilized the
impedance between 4 ohms so make it perfect match
with the amplifier。it has high efficiency and up to
1400W withstand power inAES which make it have
138dB output in peak;
The cabinet is made of birch wood with CNC and with
ivory white surface treatment. for the HF section it
machining of aluminum alloy with CNC process.
MONSTER121S is the recommend subwoofer to the
sub212 and it can stack on the floor so it can use in
nightclub and the place where need sound
reinforcement in medium throw；

Acoustics
AES Power LF:1400W / HF 80W
Program Powe LF 2800W / HF 160W
Nominal impedance 4Ω
Frequency Range LF:48~2.3kHz
HF:900~20kHz(-10dB)
Frequency Response 55~18.5kHz
Sensitivity LF 100dB；HF 110dB(1W/m)
Maximum SPL ＞132dB/138dB
Coverage Angle
Horizon 110°
Vertical 80° (Up20°+Down60° )
Drivers
LF driver 2x 12" Neodymium driver (V.C:4")
HF driver 1x1.4" Neodymium driver(V.C:2.5")
Connector
5xNEUTRIK® NL4 SPEAKON
LF INPUT1±；LINK：2±
HF INPUT2±；
Cabinet
CNC 、tongue and groove cabinet、18mm birch wood
Environmental ivory white surface treatment
Hanging Accessories
4 pcs Ø40 hoisting ring for quickly mounting
Product dimension/Packing dimension
HF
LF W750xH549xD739mm / W910xH510xD780
N.W/G.W
HF 8.5kg/ 12kg
LF 39.5kg/ 51kg
: :
: : :
:
: (-10dB)
:
: : :
:
:
:
::
::
:Packing dimension W460xH430xD440
:
:
:
SPECIFICATIONS
739
613
750
364
549
742
Monster212 is a two way full range speaker that
combine by individual dual 12 inch LF speaker and one
2.5 inch HF compression driver with BI-AMP design . it
have own passive filer in the LF speaker and HF
speaker that it can driving by amplifier directly .
Monster series speaker is the perfect combination with
the science and acoustics .With excellent acoustic
phase and frequency response it can make you have a
good listening experience in high pressure level; it
have excellent performance in high frequency cause
the horizontal asymmetric design horn and the
impedance compensation circuit which stabilized the
impedance between 4 ohms so make it perfect match
with the amplifier。it has high efficiency and up to
1400W withstand power in AES which make it have
138dB output in peak;
The cabinet is made of birch wood with CNC and with
ivory white surface treatment. for the HF section it
machining of aluminum alloy with CNC process.
MONSTER121S is the recommend subwoofer to the
sub212 and it can stack on the floor so it can use in
nightclub and the place where need sound
reinforcement in medium throw；

747
595
790
80 1.3k
Monster121S is the single 21 inch subwoofer speaker
and it's special design for MONSTER212 speaker.it
have good performance in high SPLcause the
optimized cabinet structure design for the driver.
The MONSTER121S adopts an ultra large power
driver with a power up to 2000W in 4 omh and a voice
coil of 6 inch.we recommended use amplifier with
power at least RMS 2400W to driving the speaker to
get the best performance.
The tongue and groove cabinet is made of birch wood
which ensure the strength of the cabinet,reasonable
cabinet volume design let it have amazing punch in
low frequency.
Acoustics
AES Power 2000W
Program Power 4000W
Nominal impedance 4Ω
Frequency Range 25~1.4kHz (-10dB)
Sensitivity 97.5dB(1W/m)
Maximum SPL ＞130dB/136dB
Drivers
1x 21" (V.C:6")
Connector
2xNEUTRIK® NL4 SPEAKON
INPUT 1±；LINK：2±
Cabinet
CNC 、tongue and groove cabinet、18mm
birch wood
Environmental ivory white surface treatment
Product dimension/Packing dimension
W747xH595xD790mm / W910xH770xW960
N.W/G.W
71.5kg / 87kg
:::
:
Frequency Response:28~100Hz
::
Carbon fiber cone ferrite driver
:
SPECIFICATIONS SYSTEM CONFIGURATION
HF section
①Remove 4 pcs M4x30 screw then lock the HF pedestal
②Put the HF section on the pedestal;
③Use the M8 axle screw lock the HF section and HF pedestal;
④Lock the stand bar by 4 pcs M4X12 screw(it can choose the
vertical angle at 0°or -6°of the HF section).
;
Stacked installation
⑤Remove 4 pcs M8X50 screws of the subwoofer
then fixed the T shape support rod（not need to
tighten the M8 screws at this moment）
⑥Place full range speakers on subwoofer
⑦Remove the M8x50 screws of the full range
speaker and choose the angle
you need then tighten all the M8 screws.
;
Connection
⑧As following wiring diagram it used external
DSP to management the different range
frequency to Corresponding speakers;
⑨Recommended the crossover frequency as
following diagram.
Detachable hoisting ring for hanging
System wiring
①
②
③⑥
⑤
⑦
⑧
④
MONSTER
1±
1±
2±
2±
The HF section support rod is attach in the packing:
Function:
link the cabinet and the HF section(The screws are preset
at the mounting position).
Caution:
It must used M6x12 countersunk screw to lock the HF
section support rod.
Processor Amplifier
Power

747
595
790
80 1.3k
Monster121S is the single 21 inch subwoofer speaker
and it's special design for MONSTER212 speaker.it
have good performance in high SPLcause the
optimized cabinet structure design for the driver.
The MONSTER121S adopts an ultra large power
driver with a power up to 2000W in 4 omh and a voice
coil of 6 inch.we recommended use amplifier with
power at least RMS 2400W to driving the speaker to
get the best performance.
The tongue and groove cabinet is made of birch wood
which ensure the strength of the cabinet,reasonable
cabinet volume design let it have amazing punch in
low frequency.
Acoustics
AES Power 2000W
Program Power 4000W
Nominal impedance 4Ω
Frequency Range 25~1.4kHz (-10dB)
Sensitivity 97.5dB(1W/m)
Maximum SPL ＞130dB/136dB
Drivers
1x 21" (V.C:6")
Connector
2xNEUTRIK® NL4 SPEAKON
INPUT 1±；LINK：2±
Cabinet
CNC 、tongue and groove cabinet、18mm
birch wood
Environmental ivory white surface treatment
Product dimension/Packing dimension
W747xH595xD790mm / W910xH770xW960
N.W/G.W
71.5kg / 87kg
:::
:
Frequency Response:28~100Hz
::
Carbon fiber cone ferrite driver
:
SPECIFICATIONS SYSTEM CONFIGURATION
HF section
①Remove 4 pcs M4x30 screw then lock the HF pedestal
②Put the HF section on the pedestal;
③Use the M8 axle screw lock the HF section and HF pedestal;
④Lock the stand bar by 4 pcs M4X12 screw(it can choose the
vertical angle at 0°or -6°of the HF section).
;
Stacked installation
⑤Remove 4 pcs M8X50 screws of the subwoofer
then fixed the T shape support rod（not need to
tighten the M8 screws at this moment）
⑥Place full range speakers on subwoofer
⑦Remove the M8x50 screws of the full range
speaker and choose the angle
you need then tighten all the M8 screws.
;
Connection
⑧As following wiring diagram it used external
DSP to management the different range
frequency to Corresponding speakers;
⑨Recommended the crossover frequency as
following diagram.
Detachable hoisting ring for hanging
System wiring
①
②
③⑥
⑤
⑦
⑧
④
MONSTER
1±
1±
2±
2±
The HF section support rod is attach in the packing:
Function:
link the cabinet and the HF section(The screws are preset
at the mounting position).
Caution:
It must used M6x12 countersunk screw to lock the HF
section support rod.
Processor Amplifier
Power

③
①
②
⑦
④
P/N： 924000320002400
P/N： 924000320002300
⑧
ProcessorPower amplifier
MONSTER
1±
1±
1±
1±
2±
2±
Dual stacked installation
①Accordance with the same steps of the single stack, two
HF components are mounted on one of the speakers on
the ground;
②Stacked the subwoofer;
③Fixed the T shape support rod(not need to tighten screw
at this moment);
④Upside down another speaker and stack it between the
subwoofer and T shape support rod then adjust the angle
and then tighten the screws;
⑤Remove 4 pcs connect rod in the full range speaker;
⑥Place the full range cabinet with two HF sections on the
subwoofer by two man together and keep it in right
position;
⑦Fixed the speaker by the connect rod.
System wiring
⑧Use external frequency division to driving;
Refer to the following wiring diagram:
SYSTEM CONFIGURATION
Accessories(optional parts)
T shape support rod optional angle
Single stack 0 °, -4 °, -8 °
Double stack 0 °, -6 °, + 8 °

③
①
②
⑦
④
P/N： 924000320002400
P/N： 924000320002300
⑧
ProcessorPower amplifier
MONSTER
1±
1±
1±
1±
2±
2±
Dual stacked installation
①Accordance with the same steps of the single stack, two
HF components are mounted on one of the speakers on
the ground;
②Stacked the subwoofer;
③Fixed the T shape support rod(not need to tighten screw
at this moment);
④Upside down another speaker and stack it between the
subwoofer and T shape support rod then adjust the angle
and then tighten the screws;
⑤Remove 4 pcs connect rod in the full range speaker;
⑥Place the full range cabinet with two HF sections on the
subwoofer by two man together and keep it in right
position;
⑦Fixed the speaker by the connect rod.
System wiring
⑧Use external frequency division to driving;
Refer to the following wiring diagram:
SYSTEM CONFIGURATION
Accessories(optional parts)
T shape support rod optional angle
Single stack 0 °, -4 °, -8 °
Double stack 0 °, -6 °, + 8 °

User's manual
www.verityaudio.fr