Verity Audio MUSE P User manual

MUSE P active loudspeaker series
User’s manual
www.verityaudio.fr
VN:2

Thank you for purchasing the MUSE P series active loudspeaker system.
Designed with European customize speaker,MUSE P series active loudspeaker have a very flat
frequency response in it working frequency range, high frequency and low frequency have a smooth
connection by the right X-over point, it's very good for near field amplification.
MUSE P series can output a very deep and warm low frequency when install close to the wall, because
of special designed of the vent in cabinet.
The SUB P series active subwoofer used the 15" european customize woofer which is specially used for
MUSE P series full frequency loudspeaker.SUB P series active subwoofer can output very deep and
warm sound when it near the wall because of special designed of the vent in cabinet.
1x Locking IEC power connector ; 2xXLR audio input ; 1xcombo MIC input
CNC tongue and groove cabinet wood Environmental surface treatment
Universal power supply 96–265 VAC, 50 to 60 Hz
Model MUSE8P MUSE12PMUSE10P MUSE15P
Input Sensitivity:
*Short term max SPL:
Frequency Range(-10dB):
AC Power Input:
Speaker Drivers LF:
HF:
Amplifier:
Cooling:
Connector
Cabinet
Product dimension(mm)
Packing dimension(mm)
N.W/G.W
Coverage (h x v):
(rotatable)
32dB
dB128
55~18kHz
90°x60°
1x10"(V.C:1.8")
1x1"(V.C:1")
330x380x540
457x407x616
17.2kg/21.2kg
32dB
126
55~18kHz
90°x60°
1x8"(V.C:1.8")
1x1"(V.C:1")
Class D
passive
dB
280x330x460
407x357x533
14.2kg/16.9kg
32dB
dB132
50~18kHz
90°x60°
1x12"(V.C:2")
1x1"(V.C:1.4")
395x450x640
547x492x733
23.8kg/31.3kg
32dB
dB134
48~20kHz
90°x60°
1x15"(V.C:2.5")
1x1.4"(V.C:2.5")
470x520x740
617x567x833
30.4kg/40.3kg
Model SUB115P SUB215P
*1 m, free field, SPL max peak test signal: pink noise with crest factor 4
All specifications are subject to change without notice.
Input Sensitivity(v):
*Short term max SPL(dB):
Frequency Range(-10dB):
AC Power Input:
Speaker Drivers :
Amplifier:
Cooling:
Connector
Cabinet
Product dimension(mm)
Packing dimension(mm)
N.W/G.W
32dB
passive
133
35~150Hz
Universal power supply 96–265 VAC, 50 to 60 Hz
1x15"(V.C:3")
Class D
1x Locking IEC power connector ; 2xXLR audio input
CNC tongue and groove cabinet wood Environmental surface treatment
500x700x500
797x597x593
36.5kg/44.6kg
32dB
136
35~150Hz
2x15"(V.C:3")
1000x700x500
797x597x1093
65.1kg/74.8kg
SPECIFICATIONS

CONTROL PANEL
MUSE8P/10P/12P/15P
SUB115P/SUB215P
Signal input/thru
(20 kΩ balanced
10 kΩ unbalanced)
The power input(On/Off)
Temperature/
indicating
Volume
OLED
Front LED (On/Off)
MIC Input(combo)
Max input:100mV
Volume
Power amplifier
Status indication
Signal input/thru
(20 kΩ balanced
10 kΩ unbalanced)
Xover frequency
adjustment(60~150Hz)
Polarity (Normal/Reverse)
The power input(On/Off)
Temperature/
indicating
Volume
OLED Volume
Front LED
(On/Off)
Power amplifier
Status indication
100-240
100-240
100-240

INSTALLATION
P/N: 924000260000500
910mm
M8x30
Angle adjustment:
MUSE P series loudspeaker have a rotatable horn,
so you can adjust it by yourself when you need to
change the angle.
Default angle:
Horizon 90°
Vertical 60°
Logo Angle adjustment:
MUSE series loudspeaker have a
rotatable Logo. Pull out the logo
3 to 6 mm gently and then rotate it
Support:
With M20 inner thread aluminum chassis seat
Loudspeaker support rod with M20 thread.
Hanging:
MUSE series loudspeaker has M8 flying points,
you need to remove the screws of the flying points
when need to hang the loudspeaker.
And must check if all the screws are screw in to
the flying points after installation, if not it may
cause air leakage and make sound worse.
rotatable
rotatable

INSTALLATION
A safety security stell wire is necessary ！
Adjust the angle
M8x30 eye bolt
Eye bolt
M8x30
20-30cm
Install loudspeaker with bracket:
Choose the right flying points and install with bracket*.
There is no bracket in the package, please
purchase by yourself.
a safety security stell wire is necessary!
Install loudspeaker with eye bolt:
Choosing the right flying points and install with
eye bolt.
When installation try your best to make cabinet
close to the wall 20cm to 30cm , that can improve
the bass performance.
There is no eye bolt (M8x30mm) in the
package, please purchase by yourself.
To achieve the best low frequency performance,
should assemble the cabinet close to the corner.
The back hole of the cabinet should be keep
20-30cm from the wall.

VerityAudio reserves the right to make any changes to the product specifications without prior notice.
Final specifications to be found in the user manual.