Vermont Castings Savannah SSI30 User manual
For Residential Installation
6" (152 mm) Flue Required
Owners Manual
63D4004 12/11 Rev. 9
203061
VSI30 cover
SSI30 Wood Insert
263D4004
Congratulations on your choice of a Vermont Castings Savannah. With this purchase, you
made a commitment to make the hearth a place of warmth, beauty and comfort in your home.
At Vermont Castings, we share that joy and appreciation of the hearth, and we show it in all our
cast iron inserts and replaces.
As you become acquainted with your new insert, you will nd the aesthetic appeal of cast iron
is matched only by its superb capacity to absorb and radiate heat.
Also, Vermont Castings products are among the cleanest burning wood inserts and replaces
available today. As an owner of a Vermont Castings insert, you are making a strong statement
for pollution-free energy. But clean burning depends on both the manufacturer and the operator.
Please read this manual carefully to understand how to properly operate your insert.
At Vermont Castings, we are equally committed to your satisfaction as a customer and that is
why we maintain an exclusive network of the nest dealers in the industry. Chosen for their
expertise and dedication to customer service, our dealers are factory-trained and know each
Vermont Castings product in detail. Feel free to contact your Authorized Vermont Castings Dealer
anytime you have a question about your insert or its performance.
We have built your insert with the utmost care. With normal use and proper care, it will provide
you with many years of service.
This manual contains valuable instructions on the installation and operation of your Vermont
Castings insert. You will also nd useful information on assembly and maintenance procedures.
We urge you to read the manual thoroughly and to keep it as a reference.
Sincerely,
This manual describes the installation, operation, and maintenance of the Vermont Castings
Savannah wood burning heater. This heater meets the U.S. Environmental Protection Agency’s
emission limits for wood heaters sold on or after July 1, 1990. Under specic test conditions this
heater has been shown to deliver heat at rates ranging from 11,000 to 30,600 Btu/hr.
The insert has been tested and is listed by OMNI - Test Laboratories, Inc. of Portland, Oregon.
The test standards are ANSI/UL-1482 for the United States, and ULC S628 for Canada. The
Savannah is listed for burning wood only. Do not burn other fuels.
Installation or service of this woodburning insert should only be completed by a qualied installer,
preferably NFI or WETT (Canada) certied.
Please read this entire manual before you install and use your new insert. Failure to follow
instructions may result in property damage, bodily injury, or even death.
SSI30 Wood Insert
63D4004 3
Questions ..................................................................... 3
Safety Information ........................................................ 4
Insert Dimensions and Specications........................... 6
Surround Options ......................................................... 6
Pre-installation instructions........................................... 7
Clearances ................................................................... 8
Floor Protection ............................................................ 8
Chimney Clearances .................................................... 9
Installation ...................................................................11
Operation .................................................................... 16
Maintenance ............................................................... 18
Replacement parts ..................................................... 20
FAQs........................................................................... 22
Warranty ..................................................................... 24
Gold Door Trim SSW30GDTK
Nickel Door Trim SSW30NDTK
Adjustable Raised Hearth Kit SSI30AH
Offset Flue Kit OFC3 & OFC6
Read these instructions carefully before installing or trying to operating this woodburning appliance.
Please leave these instructions with the appliance.
Please retain these instructions for future reference.
WARNING
!
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
First, contact the Vermont Castings Dealer from whom you purchased your insert, for parts and
service. Have the following information ready:
• Date of purchase
• Serial number (from the back of your insert)
• Model number (from the back of your insert)
• Dealer name and phone
If you still need assistance, contact Vermont Castings technical support (below).
See the last page of this manual for general warranty information. For additional information, contact
your Vermont Castings dealer or Vermont Castings Parts and warranty.
Before installing your appliance, be sure to write down the model and serial numbers and keep
them in a safe place. Once installed, this information is no longer visible on your appliance.
SSI30 Wood Insert
463D4004
Read all instructions and warnings carefully before starting installation. Failure to
follow these instructions may result in a possible re hazard and will void the warranty.
Vermont Castings inserts and component parts have been
tested to operate safely when installed in accordance with
instructions provided in this manual. Carefully read and
understand all instructions before beginning installation.
If you notice any damage to insert or component parts,
immediately report damage to your Vermont Castings
dealer.
Only use Vermont Castings components or the warranty
will be voided and a re hazard may be created.
Vermont Castings warranty will be voided by and Vermont
Castings disclaims any responsibility for the following ac-
tions:
•
•
(except for chase ash-
ings as detailed in Vermont Castings Chimney Top
installation instructions).
• Vermont
Castings
•
Vermont Castings
Vermont Castings
Consult local building codes to ensure that you are in
compliance installing the insert.
This insert and chimney system must be vented out-
doors.
1. Check with the building inspector’s ofce for compliance
with local codes; a permit may be required.
2. This appliance requires a masonry or prefabricated
chimney listed to ULC S629 (Canada) and UL 103HT
(U.S.) sized correctly.
3. A 6" (152 mm) diameter ue is required for proper
performance.
4. Always connect this unit to a chimney and VENT
TO ANOTHER ROOM OR INSIDE A BUILDING.
connect this unit to any duct work to which
another appliance is connected such as a furnace.
connect this unit to a chimney ue serving
another appliance.
The connector pipe and chimney should be inspected
periodically and cleaned if necessary.
8. Remember the clearance distances when you place
furniture or other objects within the area. store
wood, ammable liquids or other combustible materials
too close to the unit.
9. Contact your local municipal or provincial re authority
for information on how to handle a chimney re. Have
a clearly understood plan to handle a chimney re. In
the event of a chimney re, turn air control to closed
position and
tamper with combustion air control beyond
normal adjustment.
SSI30 Wood Insert
63D4004 5
— 6" (152 mm)
Draft is the force, which moves air from the appliance up
through the chimney. The amount of draft in your chimney
depends on the length of the chimney, local geography,
nearby obstructions, and other factors. Too much draft
may cause excessive temperatures in the appliance. An
uncontrolled burn, a glowing red part or chimney connector
indicates excessive draft. Inadequate draft may cause back
pufng into the room and “plugging” of the chimney and/or
cause the appliance to leak smoke into the room through
appliance and chimney connector joints.
Today’s solid fuel appliances are much more efcient than
in the past. The units are designed to give you controlled
combustion, as well as maximum heat transfer, using less
fuel to do so. The design of your new appliance is such that
the exhaust “smoke” is now at lower temperatures than in
the past, therefore requiring proper chimney size to give
adequate draft. If your chimney is too large, the heating
appliance will have a difcult time to raise the “chimney
ue” temperature to give adequate draft, therefore causing
a smoke back up, poor burn, or both.
With the door closed, the rate of burning is regulated by
the amount of air allowed to enter the unit through the air
control. With experience you will be able to set the control
for heat and burning time desired.
Do not abuse the glass by slamming the door or striking
the glass with a log. Never operate your insert if it has
damaged or broken glass. If you need to replace the glass,
use only replacement glass provided by your Vermont
Castings dealer.
Once the required chimney draft is obtained, operate only
with doors closed and open slowly when re-fueling. (This
will reduce or eliminate smoke from entering the room.)
Attempts to achieve higher output rates that exceed heater
design specications can result in permanent damage to
the heater. The recommended wood load is level with the
top of the rebricks. Overloading may prevent sufcient
air entering the heater to properly fuel the re.
For optimum heater performance at “low”
burn rate, operate the fan at low speed.
Standard Blower: 110v 130 CFM
• Adjustable wrench
• Flat & Phillips screwdriver
• Drill
• Tape measure
• Safety gloves
• Eye protection
• Appropriate venting components
• Furnace cement
This manual suits for next models
1
Table of contents
Other Vermont Castings Indoor Fireplace manuals
Vermont Castings
Vermont Castings TrimWorks DVA4136 Assembly instructions
Vermont Castings
Vermont Castings MLDV500NSCSB Manual
Vermont Castings
Vermont Castings RFS22 User manual
Vermont Castings
Vermont Castings Allura-Fire Markham Combo MKWCO33 User manual
Vermont Castings
Vermont Castings International Collection ICVCEFP01 User manual
Vermont Castings
Vermont Castings VCFDVI31 User manual
Vermont Castings
Vermont Castings RFSUV34 Mounting instructions
Vermont Castings
Vermont Castings MAGNUM MCUF36E-F User manual
Vermont Castings
Vermont Castings WDVST500NTSCSB User manual
Vermont Castings
Vermont Castings Merrimack Large Mounting instructions
Vermont Castings
Vermont Castings VC41LDVINTSC User manual
Vermont Castings
Vermont Castings A232 User manual
Vermont Castings
Vermont Castings DVR33 Mounting instructions
Vermont Castings
Vermont Castings DSR42 User manual
Vermont Castings
Vermont Castings 30ILDVNV User manual
Vermont Castings
Vermont Castings ChateauTM DTV38s2 User manual
Vermont Castings
Vermont Castings Lexington LX32DV User manual
Vermont Castings
Vermont Castings SB100 User manual
Vermont Castings
Vermont Castings BE36 User manual
Vermont Castings
Vermont Castings Intrepid II 1308 User manual
Popular Indoor Fireplace manuals by other brands
Napoleon
Napoleon NEFL42CHD-1 manual
Masport
Masport WOOD FIRE installation guide
JAYLINE
JAYLINE SS280 Installation & operation instructions
Heat-N-Glo
Heat-N-Glo SL-32S Installation
kozy heat
kozy heat Bellingham 52 quick start guide
Paragon Fires
Paragon Fires ROOM SEALED INSET LIVE FUEL EFFECT GAS FIRE owner's manual
Monessen Hearth
Monessen Hearth LCUF32CR-B Installation & owner's manual
PuraFlame
PuraFlame Galena owner's manual
Dimplex
Dimplex Toluca Deluxe instruction manual
SEI
SEI TENNYSON FA8544AO Assembly instructions
Dru
Dru G25 installation manual
Capital fireplaces
Capital fireplaces Designline DL700 Installation and user instructions
IronStrike
IronStrike VINTAGE VINT-DVS-U Installation and operation
ACR Heat
ACR Heat HERITAGE N25 Installation and operating instruction manual
European Home
European Home HVF-42 Installation, operation and owner's manual
Quadra-Fire
Quadra-Fire MTVERNINSAE-MBK Owner's manual operation & care
Harman Home Heating
Harman Home Heating Accentra Insert Installation & operating manual
Trimline Fires
Trimline Fires Zircon 1024 installation instructions