VETRON 5390 User manual

5390 » INSTRUCTION MANUAL
07/2018

5390 » INSTRUCTION BOOK
07/2018

© VETRON | TYPICAL GmbH
Clara-Immerwahr-Str. 6
67661 Kaiserslautern, Germany
Tel.: [phone] - 0
Fax: [phone] - 11
[e-mail]
www.vetrontypical.com
All rights reserved.
The instructions for use, service instructions, parts lists are protected by copyright. Any reuse of the
content outside the copyright is without the written consent of VETRON | Typical GmbH inadmissible
and punishable.
VETRON | Typical GmbH is only liable for damage caused by intent or gross negligence on the part of
the manufacturer. Moreover, liability is excluded.
Reserve technical changes!
The contents were carefully prepared and checked by the publisher. Due to continuous develop-
ments, illustrations, functional steps and technical data may dier slightly.
Updating the documentation
If you have suggestions for improvement or have detected any irregularities, please contact us.
The documents for the machines can be accessed by logging on
https://www.vetrontypical.com/ downloaded for free.
CE marked after §7 Prod SG

03
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
INDEX
VETRON 5390 - POST BED MACHINE
01. PREFACE
05 01. SAFETY INSTRUCTIONS
06 02. SYMBOLISM
07 03. DANGER NOTES
08 04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION
09 05. TECHNICAL DATA
10 06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE |
FIRST COMMISSIONING / DECOMMISSIONING
02. MACHINE DESCRIPTION
11 01. OVERVIEW
12 02. OPERATING PANEL
13 03. HOTKEYS
14 04. ELECTRONIC HANDWHEEL & REVERSE SEWING
15 05. CONTROL & MAIN SWITCH
16 06. PEDAL
17 07. LIGHT
18 08. MACHINE START
19 09. PROGRAM CHANGE
20 10. DIRECT ACCESS

04 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
03. OPERATION OF THE MACHINE
21 01. INSERTING THE NEEDLE
22 02. SEWING FEET EXCHANGE
23 03. THREADING THE MACHINE
24 04. EXCHANGING THE BOBBIN AND ADJUSTING THE BOBBIN THREAD TENSION
25 05. WINDING THE BOBBIN THREAD
26 06. ENGAGING THE SAFETY CLUTCH
27 07. SAFETY SPRING
04. MAINTENANCE
28 01. MAINTENANCE INTERVALS
29 02. OIL LEVEL CHECK
30 03. CLEANING THE MACHINE
31 04. SEWING DRIVE
32 05. PNEUMATIC SYSTEM
05. PROGRAMMING
33 01. GENERAL
34 02. CREATE PROGRAMNAME AND STORING
35 03. CHANGE PROGRAM NAME
36 04. PROGRAM PARAMETER
50 05. CREATE PROGRAMCHAIN
54 06. PROGRAMADMINISTRATION WITHOUT USB DONGLE
56 07. PROGRAMADMINISTRATION WITH USB DONGLE
60 08. UPDATE THE OPERATING PROGRAM
06. WIRING DIAGRAM
61 01. VETRON 8340 CONTROL BOX
07. ERROR CODES
67 01. SUPPORT FORMULAR
68 02. ERROR MESSAGES
INDEX
VETRON 5390 - POST BED MACHINE

05
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
01. SAFETY INSTRUCTIONS
General Safety Instructions
This manual and the warning symbols on the machine should en-
sure the safe use of the machine, so that no accidents and injuries
may occur to you and others. Please read this instruction and also
the safety instructions of the motor manufacturer carefully.
» The machine must only be operated in accordance with its
intended purpose (for example, sewing medium to heavy ma-
terials such as jeans, leather, etc. NO tin!) and with the as-
sociated protective equipment. The relevant country-specific
safety regulations and technical data must also be observed.
» The machine should only be used in accordance with its inten-
ded purpose (eg sewing medium to heavy materials such as
jeans, leather, etc.) and with the associated protective equip-
ment. The relevant country-specific safety regulations and
the technical data must also be observed.
» The machine should only be set up and operated in dry and
well-kept rooms.
» Do not place the machines outdoors, next to radiators or heat
source. The ambient temperature should not be lower or hig-
her than between 0 ° C to 45 ° C.
» The machine must only be commissioned after the relevant
operating instructions have been taken into consideration and
by appropriately instructed operators.
»These instructions are to be stored at hand.
» The connection cable must be provided with a country-
specific approved mains plug. The mains plug must only be
connected to grounded sockets. Here a qualified specialist is
necessary.
» The machine must always have a grounding. Only over this is
a normal operation of the machine to ensure.
» The danger and safety instructions attached to the machine
must be followed.
» When replacing sewing tools such as needle, sewing
foot, stitch plate, feed dog or bobbin, when threading,
when leaving the workplace and during maintenance,
etc., the machine must be disconnected from the mains.
  Press the main switch or pull out the mains plug.
» Machines with compressed air components must be discon-
nected from the compressed air supply and the residual pres-
sure released before repair or maintenance work. Exceptions
to this are performance tests or specific settings.
» Repairs and all maintenance work should only be carried out
by qualified personnel or appropriately instructed persons.
» Work on electrical equipment must only be carried out by
qualified specialists.
 If errors are detected, stop the machine immediately.
» Work on parts and equipment that are live is not permitted.
The machine must be disconnected from the mains.
» Modifications or modifications to the machine must be carried
out in compliance with all relevant safety regulations. The
manufacturer assumes no responsibility for damage caused
by changes or modifications.
» For repairs, only spare parts approved by VETRON may be
used. In case of infringement the guarantee expires.
»The machines are to be used only for the purpose intended.
» If oils, greases, etc., used for the machines and accessories,
get in your eyes or on your skin, or should you swallow any of
these fluids, wash them immediately and thoroughly, or seek
medical attention immediately.
» Commissioning of the machine is prohibited until it has been
determined that the entire sewing unit complies with the pro-
visions of the EC directive and the declaration of conformity
has been created.
Advice to the Owner
» As part of the machine, this operating manual must be availab-
le to operating personnel at all times. Before using the machine
for the first time, the operator must read this operating manual.
» The operator has to ensure that the machine is only operated
in perfect condition.
» The operator must ensure that no safety devices are removed
or disabled.
» The operator must ensure that only authorized or properly in-
structed persons work on the machine.
»
The operator must therefore ensure that the workstations ac-
cording to ASR lux. 4 are adequately illuminated (min. 750 lux).
Operators and Technical Sta
» The operating personnel are responsible for setting up, ope-
rating and cleaning the machine and responsible for the eli-
mination of faults.
» Qualified personnel include people with specialist trai-
ning in electrical / electronics, pneumatics and mechanics.
 Lubrication, maintenance, repair and adjustment is your
responsibility.
» The operator must refrain from any operation that the safety
on the machine is impaired.
1. Jewelry, chains and rings - must not be worn.
2. The clothes should be tight
3.
In the danger area only authorized persons may be present.
» If changes occur to the machine that aect safety, they must
be reported immediately to the operator.
» The specialist personnel - persons with training in electrical /
electronics and mechanics - are responsible for the lubrica-
tion, maintenance, repair and adjustment of the machine.
» Before starting adjustment and repair work, the main switch
must be switched o and secured against reclosing.
» Work on parts that are under tension should be avoided. Ex-
ceptions are regulated by EN 50110. After maintenance and
repair work, the protective covers must be replaced.
»
Operating and specialist personnel are obliged to observe the sa-
fety instructions given in the instructions for use during all work.

06 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
02. SYMBOLISM
DANGER!
This symbol, in combination with the
word DANGER, indicates an imminent
danger that may result in serious injury
or death.
WARNING!
This symbol in combination with the
word WARNING indicates a potentially
hazardous situation which, if not avoided,
could result in serious injury or death
ATTENTION!
This symbol in combination with the
word ATTENTION may indicate a
potentially hazardous situation that
could result in minor personal injury
.
DANGER OF CUTS!
This symbol indicates that there is an
increased risk of cuts here.
CRUSHING!
This symbol indicates that there is a
heightened risk of crushing
RISK OF BURNS!
This symbol indicates that there is an
increased risk of burning here.
MAGNET!
This symbol indicates that there is a
magnet field.
INFORMATION!
This symbol displays information.
ADVICE!
This symbol indicates important
information
.
1
2
OFFON
HARMFUL TO HEALTH!
May damage certain organs. Can lead to
immediate and long-term massive
impairment of health, cause cancer,
damage genetic material, fertility or
development. May be fatal if infiltrated
into the respiratory tract.
HAZARD TO WATERS!
May cause acute or long-term damage
to aquatic organisms such as fish,
aquatic insects and aquatic plants in low
concentrations.
PROTECTIVE EARTHING!
Earthing one or more points of a
network, installation or equipment for
the purpose of electrical safety.
DANGER LAB
Do not work the machine without finger
guard and safety covers!
Before threading, changing the needle,
adjusting, changing the bobbin, cleaning,
maintenance, etc. switch o the main
switch on the control.

07
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
03. DANGER NOTES
1 THREAD TAKE UP LEVER
2 SEWING ZONE
3 BOBBIN THREAD WINDER
4 ZONE BETWEEN MACHINE AND TABLE
CRUSHING
Crushing and bruises through the thread take up lever 1
Make sure thread take up lever guard is mounted.
Risk of injury due to movement of the lever.
CRUSHING
Crushing and bruises through the needle and sewing feet 2
Make sure fi nger guard is mounted.
Risk of injury through needle and feet movement.
DANGER OF CUTS
Cuts through rotation 3
Keep distance from bobbin winder while winding.
Risk of injury due to rotation.
CRUSHING
Crushing and bruises due to tilting the machine 4
Make sure safety spring 5 is mounted.
Risk of injury when machine is tilted back.
SAFETY PRECAUTIONS
The eye protection 6 can be ordered optionally, but must not be removed
after installation without consultation with the operator.
The fi nger guard 7 must not be removed!
6 EYE GUARD
5 SAFETY SPRING
7 FINGER GUARD

08 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
1-NEEDLE LOCKSTITCH SEWING MACHINE WITH DIRECT DRIVE
AND TRIPLE FEED
The consistent use of state-of-the-art control technology has made it possible to program all ma-
chine parameters programmatically, making them directly accessible. This ensures that the process
parameters are free from operator influence and after each setup.
The innovative dynamic machine parameters based on the current speed and the permanent materi-
al thickness measurement open up new paths in terms of processing quality, process reliability and
reducing cycle times.
Typical applications:
Automotive Upholstery Suitcase Bag
INTENDED USE
Any use not approved by the manufacturer is considered improper!
Proper use also includes compliance with the prescribed operating, adjustment,
maintenance and repair measures. Damage due to non-intended use is not covered by
the manufacturer‘s liability!
The VETRON 5390 and its subclasses are 1- needle lockstitch sewing machine with direct drive and
triple feed. Use the machines only according to their technical data and for medium to heavy ma-
terials such as jeans, leather, etc.. No tin! The machine is only intended for processing dry material
and must not contain any hard objects. In this respect, the seam must be made with a thread whose
requirement profile corresponds to the application purpose.
The machine is designed for industrial use.
The operator is obliged to carry out a risk assessment in accordance with the Work Protection Act
(ArbSchG).
CE-CONFORMITY DECLARATION
All VETRON sewing machines comply with the applicable European regulations of relevant basic
health and safety requirements, which are specified in the declaration of conformity and manufac-
turer.
01. PREFACE
04. PRODUCT INTRODUCTION / INTENDED USE / CONFORMITY DECLARATION

09
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
Technical Data Vetron 5390
Stitch type 301 1-needle lockstitch with triple transport
Needle system 134-35
Needle size 90-140 for sewing middle heavy materials
Thread size 20/3 (depending on version)
Max. Stitches/minutes 1500
Max. Stitch length 6mm
Max. clearance under the sewing feet 20mm
Max. top-feed-stroke 9mm
Clearance space 350 x 570mm
Table plate size 640 x 200mm
Netto weight 80 kg
Gross weight 114kg
Operating voltage AC 220-240V / 50-60Hz
Rated power 1200W
Noise indication 80dB(A)
Versions and subclasses can be found under:
www.vetrontypical.com
01. PREFACE
05. TECHNICAL DATA

10 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
01. PREFACE
06. TRANSPORT - PACKAGING - DISPOSAL - STORAGE |
FIRST COMMISSIONING / DECOMMISSIONING
FIRST COMMISSIONING
01. Before operating the machine, clean the machine thoroughly.
02. Check whether the machine or electrical cables are damaged.
03. Have specialists confirm that you are allowed to operate the machine with the mains voltage
and that it is correctly connected.
04. MACHINES WITH PNEUMATIC CONNECTIONS:
Connect the machine to the compressed air system. The operating pressure at the filter valve
is 6 bar.
05. All covers must be mounted.
NOTE!
1.) Should deviations occur, do not operate the machine!
2.) Only connect the machine to a grounded power outlet!
DECOMMISSIONING
01. Switch o the machine at the control.
02. Pull out the mains plug.
03. Disconnect the machine from the compressed air supply, if available.
04. Clean the machine if necessary.
05. If possible, cover the machine to avoid soiling.
TRANSPORT - PACKAGING - DISPOSAL - STORAGE
01. Transport of the machine
All machines are delivered packed.
The product must be checked for shipping damage after delivery. For subsequent damage
within the customer‘s operation, the manufacturer assumes no liability.
Make sure that the products are transported safely and with the utmost care at your facility.
 Moving machines with EHS (electrically height adjustable) with wheels:
» Turn o the machine
» Make sure that the sewing machine head is not tilted back
» Put the table in the lowest position
» Pull power and pneumatic connections
» Release wheel brakes
» Grab the table top and push the entire machine to the new location
» Reconnect the electricity and pneumatics and tighten roller brakes
02. Packaging
The packaging material must be disposed of in accordance with local environmental protec-
tion regulations.
03. Disposal
The customer is responsible for the proper disposal. Disposal should comply with local
environmental regulations.
NOTE!
Parts contaminated with lubricants or oils must be disposed of separately.
04. Storage
When not in use for a long time, the machines must be protected against dirt, moisture and
corrosion (e.g.: by an oil film).

ESC
P000 30%
TEST
11
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
01. OVERVIEW
OPERATING PANEL
HOTKEYS
CONTROL DONGLE PEDAL
ELECTRONICS AND
SEWING REVERSE

ESC
000
SE T
30%P
T
1 2 3 4
5 6 7 8 9
10
A B
12 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
02. OPERATING PANEL
The operating fi eld indicates the current operating states.
Operation takes place via continuous dialog between control and operator.
Depending on the operating state, di erent texts are displayed.
The following functions are assigned to the BUTTONS ABOVE AND BELOW THE DISPLAY:
1 BACKTACK (from left to right):
A Start backtack
B End backtack
2 THREAD TRIMMING
3 NEEDLE UP/DOWN AFTER STOP
4 LIGHT ON/OFF
5 PARAMETERS
6 NEW PROGRAM
7 PROGRAMMED SEAM
8 SAVE
9 CANCEL
If a function is activated, this is indicated by illuminating the corresponding LED.
In order to CHANGE OR SET VALUES, use the JOG KEY ( 10 ):
Turning changes the values; pressing the JOG KEY enters the value.
In the following, the operating type is indicated by the following icons:
Input = Press the JOG KEY:
Change = Turn the JOG KEY:

1
2
4
3
13
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
03. HOTKEYS
1 SAFETY SWITCH
If the safety switch is triggered, all functions are locked. The LED lights up red.
The “BLOCKED MODE” is active.
NOTICE:
Before activating the machine by the X-button make sure to remove sewing material or
other items below the sewing feet if necessary and follow the instructions displayed in the
control panel.
2 SINGLE BACKTACK SUPRESSION
If the backtack function is activated, the following backtack is switched o once
by pushing the key.
3 2ND STITCH LENGTH
If the second stitch length is activated, the corresponding LED is lit up.
4 CUSTOMIZABLE BUTTON
Default: Toggle foot stroke level
(see parameter M085)

1
2
3
14 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
NOTICE!
The electronic handwheel is not active unless the machine has performed at least one
stitch.
For safety reasons it is necessary during “BLOCKED MODE” to push and hold
the programmable button (the lowest button) 3 to activate the electronic handwheel.
1 ELECTRONIC HANDWHEEL – FUNCTION
By turning the handwheel, you can move the needle bar up or down.
In the following, the operating type is indicated by the following icons:
Pressing the handwheel: stitch-for-stitch function / needle positioning
Turning the handwheel:
2 R E V E R S E SEWING
Pulling the button changes the sewing direction.
02. MACHINE DESCRIPTION
04. ELECTRONIC HANDWHEEL & REVERSE SEWING

1
2
15
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
1 MACHINE MAIN SWITCH
Switches the machine ON / OFF
2 USB-PORT
Identify yourself using the provided USB dongle.
02. MACHINE DESCRIPTION
05. CONTROL & MAIN SWITCH

0
+1
-2
+2
-1
16 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
06. PEDAL
0 IDLE POSITION
+1 CONSTANT SEWING SPEED (adjustable via parameter M502)
+2 VARIABLE SEWING SPEED FROM 0-100%
OF THE CHOSEN MAXIMUM SPEED (depending on sewing program)
-1 SEWING FEET LIFT
-2 SEAM END PROCEDURE ACTIVATION (depending on sewing program)

17
07/2018
VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
07. LIGHT
DISPLAY STEP DESCRIPTION
»LIGHT ON/OFF
The VETRON head module is equipped with LED
lighting.
Press the LIGHT button
The corresponding LED on
the display lights up.
»ADJUST LIGHT INTENSITY
01 Press the LIGHT button
Die entsprechende LED leuchtet auf
dem Display.
02 1
A
0
J IS H
0
D LU GT T Change LIGHT INTENSITY Percentage on the display and
light intensity of the light are changed.
03 A J IS HD LU GT T
0 06 After 2 seconds without further input,
the value is set and the current program
number is shown.
04 P 2 2W 41 3 31 5
P MO NR MR G AA E Machine is ready for operation.

11
18 07/2018 VETRON 5390 - POST BED MACHINE - INSTRUCTION BOOK
02. MACHINE DESCRIPTION
08. MACHINE START
Press the main switch at the control box to turn on the machine.
01. Wait some seconds until the machine is initialized.
NOTICE!
Make sure that no sewing material or other items are below the sewing feet
before pushing the pedal.
02. Push the pedal. The sewing feet are moving and finally positioning on the needle plate.
The red and white control lights 1 at the machine head are flashing
during automatic movement.
03. The sewing light is automatically switched on.
04. The machine is now ready for use.