VEVOR W3312 User manual

Technical Support and E-Warranty Certificate www.vevor.com/support
Dog Gate
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

- 1 -
W3312/B3312 W3336/B3336
W3350/B3350 W3360/B3360
Have product questions? Need technical support? Please feel free to
contact us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
NEED HELP? CONTACT US!
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our
user manual. The appearance of the product shall be subject to the
product you received. Please forgive us that we won't inform you again if
there are any technology or software updates on our product.
Dog Gate

- 2 -
INSTRUCTIONS
Thank you very much for choosing this dog gate .
Please read all of the instructions before using it.
The information will help you achieve the best possible results.
Model and Parameters
Model
W3312
W3312
W3336
W3336
W3350
W3350
W3360
W3360
Adjustable
Width
29.5”-39”
29.5”-48.4”
29.5”-53”
29.5”-57.8”
Colour
White
Black
White
Black
White
Black
White
Black
Height
30 inch

- 3 -
Product & Parts

- 4 -
MAINTENANCE
Clean by using a sponge with warm water or mild detergent.
DO NOT use abrasive cleaners or bleach.
Check the gate regularly to ensure all hardware and mounts are securely tightened.
Do NOT use if any component is damaged or missing.
STEP 1. Measure the width of the doorways
Following the below extension combination suggestions to install the gate.

- 5 -
STEP 2.
Insert 4 bolts into 4 corners of the gate/extension.
STEP 3.
Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in
position and mark the center with a pencil.

- 6 -
PLEASE NOTE: The gate should be resting on the floor. DO NOT allow a gap of
more than 0.5cm between the gate and the floor.
STEP 4.
Stick the pad when using pressure mounted installation.
Remove two sides of the sticky pad, stick 4 pads to 4 wall cups. Then wall cups
cover the bolts.
TIP: If you do not have to worry about damaging the walls, skip this step.

- 7 -
STEP 5.
Drill hole for the 4 marked positions, then put dry wall anchor(g)and use
screw(f)and the wall cup (d)
STEP 6.
Tighten the top of the tension knobs by turning them clockwise at the same time
Note: Make sure the bottom of the gate frame remains completely flat on the floor.
Next, tighten the bottom of the tension knobs at the top at the same time by turning
them clockwise.

- 8 -
2.Pay attention to adjusting the left and right clearance to ensure that the left and
right clearance is consistent.
STEP 7.
Cut off the belt and test the gate:
1.Push the gate to check stability.
2.Open and close the walk through gate.
Pull the button to the right, then lift the gate panel UP to open.

- 9 -
TROUBLE SHOTING
·To prevent serious injury or death, securely install the gate or enclosure and use
it according to the manufacturer's instructions.
·Never use with a child able to climb over or dislodge the gate or enclo- sure.
·This product will not necessarily prevent all accidents.
·Never leave children unattended.
·Use only with the locking mechanism securely engaged
·Intended for use with children from 6 months through 24 months of age.
·Stop using the gate if any parts are missing or become damaged.
·Children may die or been seriously injured when gates are not securely installed.
·ALWAYS install and use gates as directed using all required parts.
·Periodically check all fasteners to be sure they are tight and secure.
·Adult Assembly Required.
·The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound.
·Indoor use only. It is not to be exposed to outdoor elements.
·Install this gate away from heaters and other sources of heat.
·STOP using it when a child can climb over or dislodge the gate.
·You MUST install [wall cups] to keep the gate in place. Without [wall cups], the
child can push out and escape.
·NEVER use it to keep the child away from a pool.
·Thanks for purchasing VEVOR product!

- 10 -
Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
EC REP: SHUNSHUN GmbH. Römeräcker 9 Z2021,76351
Linkenheim-Hochstetten, Germany
UK REP：Pooledas Group Ltd. Unit 5 Albert Edward House, The Pavilions Preston,
United Kingdom
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122
Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place,
Rancho Cucamonga, CA 91730
Made In China

Technical Support and E-Warranty Certificate
www.vevor.com/support