Vex Robotics Competition Turning Point Manual

Field Build Instructions
276-5677-750

12x
276-5677-010
Parts List
8x 0.5 in
275-1014-001
3x 2 in 275-1018-001
125x 8-32 Nylock
276-1027-001
50x 0.375 in
276-4991-001
20x 0.5 in
276-4992-001
66x 0.625 in
276-4993-001
30x 0.875 in
276-4995-001
8x 1 in
276-4996-001
4x 1.5 in 276-4998-001
2x
276-5677-007
9x
276-5677-008
12x
276-5677-009
9x 276-5677-013
3x 276-5677-014
7x
276-5677-015
18x 276-5677-017
22x
276-5677-019
9x 276-5677-026
42x
Hook /Loop Fastener
276-5677-036 22x 276-5677-006

7x
58 in (1473.2 mm) Pipe
276-5677-001
6x
47 in (1193.8 mm) Pipe
276-5677-002
2x
34 in (863.6 mm) Pipe
276-5677-003
6x
23 in (584.2 mm) Pipe
276-5677-004
4x 276-5677-005
4x 276-5677-040
21x 276-5156-001
4x 276-5677-041
1x Net 276-5677-016
1x 9.125 in (231.775 mm) Short Pipe
276-5677-032
1x 13.25 in (336.55 mm) Long Pipe
276-5677-033
2x 276-5677-034
20x
276-5677-200
2x
276-5677-035
8x 276-5677-100

= Tuck tape under tile
There are (7x) strips of 3/4 in White Electrical Tape on the Field,
as shown below:
IMPORTANT NOTE:
DO NOT stretch tape when applying to the foam tile oor. For best results,
smooth out any bubbles that form during application.
Note: Tabs on the foam tiles may be mirrored on your eld.
To prevent tape lines from being pulled up during competition, it is recommended
that the ends of the tape are tucked into tile seams.
Pro-Tip:
If the tiles will be used at multiple events, it is not necessary to remove the
tape. Simply cut the tape at tile seams and note the order of the tiles when they are
stored.
1
14x

5
2
Field Monitor Mount (optional)
Recommended Location
Use ¼-20 x 0.5 in
screw already on eld

0.625 in
014
6x
0.625 in
43
010
041

7
5 6 0.625 in
014
6x
0.625 in
010
040

8
70.625 in
014
8x
0.625 in
010
005

9
91 in
4x
1in
0.375 in
0.5 in
4x
4x
035
0.5 in
0.375 in

10
4x
1.5 in
1.5 in

11
0 5 6
1 4
2 33 24 15 0
0 5 6
1 4
2 3
3 2
41 5 0
4X
11
12
0.375 in
0.5 in
4x
4x
0.5 in
015
0.375 in
Locate 015 under tiles with the
stando facing up.
Note: Tabs on the foam tiles may be
mirrored on your eld.

Tabs may deform during assembly
13 4x
1in
1 in

13
14 15 16
22X 4X 2X
23 in
584.2 mm
34 in
863.6 mm
004 003
8-32 Nylock
44x
8-32 Nylock
006
14
14

17 6X
0.625 in
019
24x
0.625 in
34 in
863.6 mm
23 in
584.2 mm
34 in
863.6 mm
23 in
584.2 mm
23 in
584.2 mm
23 in
584.2 mm

15
18 19
20 12X
9X 9X
8-32 Nylock
8-32 Nylock
18x
24x
18x
013
026
8-32 Nylock
8-32
Nylock
009
8-32 Nylock
0.375 in
0.875 in
0.375 in
008
0.375 in 0.375 in
0.875 in
18x 18x
24x
Tighten only enough to
engage nut. Do not fully
tighten screws.
8-32 Nylock
18

21 3X
47in
1193.8 mm
58 in
1473.2 mm
Use 4x 006 for
Alignment
Align bottoms
After alignment
tighten screws
Assemble on at surface
002
001 20

17
22
23
3X
3X 14
14

24 3X
Short Pipe
032
After alignment
tighten screws
Use 032 for
Alignment
20
9.125 in
231.78 mm

19
25 3X
19

26 3X
033
Long Pipe
Use 033 for
Alignment
After alignment
tighten screws
20
13.25 in
336.55 mm