ViaSat SurfBeam User manual

4)
0
5
~
...,
0
••••
0
~
fIIIIII
fIIIIII
N
-~
4)
I
~
:is
...,@
~
~ a
rtJ
~:::
•••• ....,
~
cI
a ~
Q)
~
0
4)e
0
i
0
~
'tS •••
P 't
o ::s
I
- "ol
:is
:::
:? Jrn
~
rtJ
n
~
lU
CD
-
~
;::+
CD
~
Z
CD
•
~
CD
0
c
..,
;11\
~--s
n;i
0
CD
-0
0
CD
0
3
I
3
n
c
Q)
::l
o'
r-+
lU
CD
-
cf
-
::l
-
CJ)
--
n;i
r-+
CD
0
::r
•
::l ( ')
0
0
0
co
(j).
3
CJ)
CJ)
E ,~
o g
U.E
• 0
Q) ~
-+-' CJ)
-- c
- 0
- 4:#
Q) ~
-+-' '2
co ::l
n E
I . E
Q) ~
c..~
o ~
L.. ~
:J <5
]) ~
~ ;
~
rJJ
rJJrJJ
a=
s» s::
~
I
''''
t-'
~ ...•
0
:;
0
~
0
•••• (D
'I»
5
QO
(D a
~
rJJ
f'b
a= a:
®
I
0
tv
0
Q..
0
(D
0
a

1.Plug thein-linepower supplyintothe SurfBeam SM, andthen into the power
source.
2. ACrequirements are:115 or 220 VAC, 50-60 Hz.
1. Attach the base to the SM,and locate it nearyour computer.
2. Keep it away from heat,liquid, and magneticinterference.
STEP 2
Surf Beam
Satellite
Modem
EthernetCable
p, mo:
SurfBeam
SM
In-Line
Power Supply
STEP 4
1.Connect one end of the Ethernetcableto theSurfBeamSM and the other to the
Network Interface Card in your computer.
2. Connect and hand-tighten the TX and RXcables fromthe outdoor unit (ODD)
to the SurfBeam SM.
Watch the SurfBeamSM frontpanelindicators.The RX indicatorshould flashwhile
acquiring the satellite signal.When the RX indicator goes on steady,the SM is
registered.
Note:You must configure your computer to obtain an IP address from theDHCP server.
Refer to your computer's operating system (0/8)documentation for instructions.
6
PWR-On when power is applied
I
~1 flash=acquiring downstream
I 01 RX- PWR
I~I
Surf BeamRX
b
SM3flashes=registeringTX
4 flashes =software downloading
LAN
~~~~~~~
Onsteady =successful registration (normal)
Very fast flashes=fault
0000000
'C2
Your Computer
TX-On when transmitting
rf-a
LAN-Onwhen connectedto Ethernet
Flashes when traffic is on Ethernet

~RXIN
~TXOUT
Vla al
Modem Satelital
SurfBeam®
SM-IOOO Y SM-2000
uia del Usuario
1.Make sure you have satellite service. (The RXindicator should be on steady).
2.Make sure you have the Ethernet connection. (The LANindicator should be
on).
3. Make sure your are transmitting to the satellite. (The TXindicator should flash
when transmitting).
4. Make sure all the connectionsare correct and tight.
5.Try resetting the SM and in-line power supply (Disconnect the in-line power
supply from the power source, wait AT LEAST one minute, and then reconnect
power). The SM should go through acquisition and registration process again
(STEP 4).
ViaSat, Inc.
6155 El Camino Real
Carlsbad,CA 92009-1699
USA
Tel: [phone]
Fax: [phone]
ViaSat,lne. assumes no responsibility for any errorsthat mayappear in thisdocument nordoes it makeexpressed orimplied warrantyof any kind
with regardto thismaterial,including, but notlimited to, the implied warranties ofmerchantabilityand fitness for a particular purpose. ViaSat,Inc.
shall not beliable for incidental or consequential damages inconjunction with,or arisingout of thefurnishing, perfonnance, or use of this
document andtheprogram material it describes.