Vibe OPTIFIAT6-V8 User manual

High Efficiency OEM Speaker System
www.vibeaudio.co.uk
www.youtube.com/vibeaudio
www.facebook.com/vibeaudio
www.twitter.com/vibecaraudio
www.instagram.com/vibeaudio
OPTIFIAT6-V8
Fiat speaker upgrade kit
SPECIFICATION
Configuration 2-way component
Speaker Size 6.5” (165mm)
Peak/RMS Power 270W/90W
Sensitivity 94dB
Frequency Response 54Hz - 25kHz
Impedance 4Ω
Mounting Depth 2.4” (61mm)
Mounting Diameter 5.6” (142mm)
Recommended Amp POWERBOX65.4M-V7

Installation guide
• Remove vehicle door card carefully, please ensure that all
screws and clips are correctly removed and retained
• It is recommended that a set of good quality plastic trim
removal tools are used in order to prevent damage to the
door card that can be caused by using improper tools such
as a large at head screwdriver.
• Recommended VIBE trim removal set CLTRT-V7.
Contact your authorised VIBE for more information.
• Unplug factory speaker cabling.
• remove factory speaker and housing from door / door card
making sure to retain all xing hardware.
• Note : It may be necessary to drill out rivets in order to
remove the factory speaker, please take care when using
power tools so as not to damage the vehicle and ensure
protective eyeware is worn.
• Apply the Anti-Vibe sound deadening material to the outer door
skin directly behind where the speaker is to be mounted.
• Please ensure that the area is clean and free from grease
before application and applied with a hard roller and heatgun
/ hair drier in order to achieve the best adhesion.
• Recommended VIBE dampening roller CLDR-V7.
Contact your authorised VIBE for more information.
• Apply the disc of VIBE wave diffuser over the top of the sound
deadening material.
• Attach the vehicle specic adaptor ring to the door / door card.
Note : No screws or xings are supplied for the adaptor ring as
every vehicle will require different mounting hardware and in most
cases will require the factory speaker xings to be used.
2

• Insert the adjustable silicone speaker bafe into the adaptor
ring.
• Attach the speaker wiring loom adaptor to the vehicle speaker
wiring ensuring correct polarity is observed and attach to the
speaker terminals.
• Fit the OPTI6C speaker into the silicone speaker bafe and
align the screw holes before securing with the supplied
screws.
• Install the tweeter into a suitable location in the vehicle, in
most cases the location of the factory installed tweeter can
be utilised.
• Note : Methods of tting the tweeter will vary from vehicle to
vehicle and may require the tweeter to be hot glued into
place.
• Ret the vehicle door card.
Tools required
• Screwdrivers
• Torx drivers
• Battery drill driver
• Safety glasses
• Trim removal tools
• Heat gun / hair drier
• Dampening roller
• Screws / bolts / xings for speaker adaptor ring and tweeter.
• Hot glue gun (optional)
3

High Efficiency OEM Speaker System
www.vibeaudio.co.uk
www.youtube.com/vibeaudio
www.facebook.com/vibeaudio
www.twitter.com/vibecaraudio
www.instagram.com/vibeaudio
FITMENT GUIDE
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
MAKE MODEL YEAR RANGE FROM / TO
FIAT Ducato 2006>
FIAT Grande Punto 2005>
FIAT Panda 2012>
All VIBE products carry a full 12 month warranty, valid from the date of the
original receipt and proof of purchase (UK only). The online warranty card should be completed within seven days of the original purchase date. The
original receipt and packaging should be retained for this twelve month period. If the product develops a problem at any stage during the warranty period,
it should be returned to the point of purchase in its original packaging, and complete with no items missing.
A full description of VIBE’s warranty information can be found on our website:
www.vibeaudio.co.uk
What Is Not Covered
• Damage to product due to improper installation.
• Subsequent damage to other components.
• Damage caused by exposure to moisture, excessive heat, chemical cleaners and / or UV
radiation.
• Damage through negligence, misuse, accident or abuse. Repeated returns for the same fault
may be considered abuse.
• Any cost or expense related to the removal and / or re-installation of the product.
• Damage caused by amplier clipping or distortion.
• Items repaired or modied by any unauthorised repair facility.
• Return shipping on non defective items.
• Products returned without a returns authorisation number.
• Damage to product due to use of sealant.
International Warranty
Contact your international VIBE dealer or distributor concerning specic procedure for your
country’s warranty policies. www.vibeaudio.co.uk
Tel : [phone] Email : [email protected]