HOLD (Touch Hold) Modifier
The Touch Hold modifier allows you to hold the measureme t readi g o the display.
Press HOLD to select the Touch Hold modifier. Whe Touch Hold is selected, “HOLD” a u ciator is
lit o , a d the beeper emits a si gle beep. Press HOLD agai to exit Touch Hold modifier, a d the
beeper emits a si gle beep.
MN MX AVG (Minimum Maximum Average) Modifier
The MN MX modifier causes the meter to store the mi imum a d maximum i puts measured si ce
the MN MX AVG modifier was selected. Press MN MX to select the MN MX AVG modifier. Whe the
MN MX AVG modifier is first selected, the mi imum, maximum a d average values are set to the
displayed readi g a d the “MAX” a u ciator lights, o ce the maximum value showed o the primary
display, the beeper emits a si gle beep. Press MN MX agai to display the mi imum readi g a d the
“MIN” a u ciator lights, o ce the mi imum value showed o the primary display, the beeper emits a
si gle beep. Press MN MX agai to display the average readi g o the primary display (“AVG”
a u ciator lights). Each subseque t press the MN MX butto toggles amo g the mi imum,
maximum a d average measureme ts take . The measureme t readi g displayed o the seco dary
display. To exit the MN MX AVG modifier, press a d hold dow the MN MX butto for two seco ds or
press other fu ctio butto s.
Selecti g the MN MX AVG modifier tur s off autora gi g a d locks i the prese t ra ge. Make sure
you are i the correct ra ge before selecti g the MN MX AVG modifier.
COMP (Compare) Modifier
The compare fu ctio (COMP) provides a easy way to determi e if a readi g falls withi a
desig ated ra ge of values. I the compare mode, the meter displays a readi g i the seco dary
display a d i dicates i the primary display if that value is lower (CO-LO) tha , higher (CO-HI) tha ,
or withi a ra ge (PASS) you selected, if the readi g lower or higher, the beeper emits a co ti uous
to e. Compare Modifier ca be used u der dc voltage, ac voltage, dc curre t, ac curre t a d omh
fu ctio , i compare mode, the meter is i ma ually ra ge mode..
Followi g the step to e ter Compare Modifier
Select a fu ctio a d a ra ge
Press COMP to toggle i Compare Modifier
Before selecti g the compare fu ctio , set the high a d low compare poi t first, whe compare
modifier selected, “MAX” a u ciator lights, a d the leftmost digit o the primary display is
flashi g, the ca set the high poi t, press AUTO to select the digit to be set, each press AUTO
causes the digit to the right to be selected a d flashi g, press or to up or dow the
flashi g digit. Press the COMP agai , “MIN” a u ciator lights, a d the leftmost digit o the
primary display is flashi g, the ca set the low poi t, press AUTO to select the digit to be set,
each press AUTO causes the digit to the right to be selected a d flashi g, press or to up or
dow the flashi g digit. Each subseque t press the COMP butto toggles betwee high set, low
set a d compare measureme ts take . To exit the Compare Modifier, press a d hold dow the
COMP butto for two seco ds or press other fu ctio butto s.
Selecti g the Compare Modifier tur s off autora gi g a d locks i the prese t ra ge. Make sure you
are i the correct ra ge before selecti g the Compare Modifier.
The fu ctio modifier is relative to the measureme t fu ctio refer to the Table 3-5
Table 3-5. fu ctio modifier a d measureme t fu ctio
FUN. Modifier
Fu ctio
REL HOLD MNMX COMP
DCV √ √ √ √
ACV √ √ √ √
DCA √ √ √ √
