Vicon MPD-955-WM User manual

Vicon part number 8009-8194-65-00 Section 3 Rev 609
XX194-65-00
MPD-955-WM WALL MOUNT OPTION
FOR MPD-955 INDOOR CAMERA DOME
Copyright © 2009 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: [phone] WEB: www.vicon-cctv.com

XX194-65-00 Rev 609 MPD-955-WM Introduction •1
Introduction
The information in this instruction manual covers the installation of the MPD-955-WM Wall Mount for the
MPD-955 Camera Domes. These mounts should only be installed by a qualified technician using approved
materials and wiring practices in accordance with the National Electrical Code ANSI/NFPA 70, state, and
local electrical codes. Read these instructions thoroughly before beginning an installation.
The MPD-955-WM is used when installation requirements are for wall-mount pendant configurations. The
accessory kit contains all necessary hardware for installation.
Installation
Installation Preparation
Cabling should be run to the installation site before the mount is installed. Refer to instruction manual XX194-
5X for complete instructions on camera dome installation and adjustment.
Note: Verify that the selected mounting location is free of obstacles such as wiring or pipes.
Caution: Mount these units only to structural materials with sufficient strength to carry the overall weight of
the mount and unit.
Wall-Mount Installation
The MPD-955-WM is used when the MPD-955 is to be installed onto a wall or ceiling in pendant
configuration. The wall mount includes hardware necessary for installation.
1. Using the wall mount as a template, mark the location of the three mounting holes. Drill holes at these
locations and insert the anchors provided. Mounting dimensions provided for convenience.
Installing the Wall Mount
2. If not already done, route all necessary cables to the installation location.
3. Route the cables through the cable access hole in the wall mount
4. Secure the mount to the wall with the screws provided.
5. There is a metal mounting plate on the camera dome. Turn the mounting plate counter-clockwise to
remove it from the camera dome base. Refer to instruction manual XX194-5X for detailed instructions.
Line up the arrow head indicators on the mounting plate and the mount and align the cable access hole in
the mount and the plate so that two mounting holes align. Secure the mounting plate to the mount with
appropriate screws.

2 •Installation XX194-65-00 Rev 609 MPD-955-WM
Installing the Mounting Plate
6. Route cables through the cable access hole of the dome and make necessary cable connections to the
camera dome.
7. Secure the dome base to the mount/mounting plate by turning in a clockwise direction until it snaps into
the tabs.
Mounting the Camera Dome
8. Turn the lower dome counter-clockwise to remove it. Make camera and lens adjustments as necessary
and replace lower dome.
9. Secure the dustproof cover, shiny side up, by aligning the holes in the cover with the raised tabs on the
top of the mount.
Completed Installation

XX194-65-00 Rev 609 MPD-955-WM Shipping Instructions •3
Shipping Instructions
Use the following procedure when returning a unit to the factory:
1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name
of the Vicon employee who issued the R.A.
Vicon Industries Inc.
89 Arkay Drive
Hauppauge, NY 11788
Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288)
For service or returns from countries in Europe, contact:
Vicon Industries (U.K.) Ltd
Brunel Way
Fareham, PO15 5TX
United Kingdom
Phone: [phone]; Fax: [phone]
2. Attach a sheet of paper to the unit with the following information:
a. Name and address of the company returning the unit
b. Name of the Vicon employee who issued the R.A.
c. R. A. number
d. Brief description of the installation
e. Complete description of the problem and circumstances under which it occurs
f. Unit’s original date of purchase, if still under warranty
3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.
4. Mark the R.A. number on the outside of the carton on the shipping label.

4 •Technical Information XX194-65-00 Rev 609 MPD-955-WM
Technical Information
MECHANICAL
Application: Indoor.
Mounting: Wall/ceiling in pendant configuration.
Dimensions: Height: 5.0 in. (127 mm).
Width: 5.8 in. (147 mm).
Depth: 7.5 in. (190 mm)
Weight: 0.4 lb (0.18 kg).
Construction: Plastic (ABS); ivory finish.

XX194-65-00 Rev 609 MPD-955-WM Vicon Standard Equipment Warranty •5
Vicon Standard Equipment Warranty
Vicon Industries Inc. (the “Company”) warrants your equipment to be free from defects in material and workmanship under
Normal Use from the date of original retail purchase for a period of three years, with the following exceptions:
1. VCRs, all models: Labor and video heads warranted for 120 days from date of original retail purchase. All other
parts warranted for one year from date of original retail purchase.
2. Video monitor CRT (cathode ray tube) and LCD monitors, all models: One year from date of original retail
purchase.
3. Uninterruptible Power Supplies: Two years from date of original retail purchase.
4. VDR-304, VDR-308 and VDR-316 Recorder Series: One year from date of original retail purchase.
5. V5616MUX: One year from date of original retail purchase.
6. S10-CH: 18 months from date of original retail purchase.
7. Normal Use excludes prolonged use of lens and pan-and-tilt motors, gear heads, and gears due to continuous
use of “autopan” or “tour” modes of operation. Such continuous operation is outside the scope of this warranty.
8. Vicon Security Management Systems (SMS) All Models: All hardware is warranted for two years from date of
original retail purchase.
Date of retail purchase is the date original end-user takes possession of the equipment, or, at the sole discretion of the
Company, the date the equipment first becomes operational by the original end-user.
The sole remedy under this Warranty is that defective equipment be repaired or (at the Company’s option) replaced, at
Company repair centers, provided the equipment has been authorized for return by the Company, and the return shipment
is prepaid in accordance with policy.
The Company will not be obligated to repair or replace equipment showing abuse or damage, or to parts which in the
judgment of the Company are not defective, or any equipment which may have been tampered with, altered, misused, or
been subject to unauthorized repair.
Software supplied either separately or in hardware is furnished on an “As Is” basis. Vicon does not warrant that
such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be
discontinued at any time without notice at Vicon’s sole discretion. Vicon reserves the right to make changes to
its software in any of its products at any time and without notice.
This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods, including any
warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies
available to the Purchaser.
No one is authorized to assume any liability on behalf of the Company, or impose any obligations on it in connection with
the sale of any Goods, other than that which is specified above. In no event will the Company be liable for indirect, special,
incidental, consequential, or other damages, whether arising from interrupted equipment operation, loss of data,
replacement of equipment or software, costs or repairs undertaken by the Purchaser, or other causes.
This warranty applies to all sales made by the Company or its dealers and shall be governed by the laws of New York
State without regard to its conflict of laws principles. This Warranty shall be enforceable against the Company only in the
courts located in the State of New York.
The form of this Warranty is effective December 8, 2008.
THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT. THIS
WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE
COMPANY’S WEBSITE, WWW.VICON-CCTV.COM. IN THAT EVENT, THE TERMS OF THE POSTED WARRANTY
SHALL APPLY EXCLUSIVELY.
Vicon Part Number: 8006-9010-03-06 Rev 1208

Vicon Industries Inc.
Corporate Headquarters
89 Arkay Drive
Hauppauge, New York 11788
631-952-CCTV (2288) 800-645-9116
Fax: 631-951-CCTV (2288)
Vicon Europe
Headquarters
Brunel Way
Fareham, PO15 5TX
United Kingdom
[phone]
Fax: [phone]
Germany
vin-videotronic infosystems gmbh
Lahnstrasse 1
D-24539 Neumuenster
Phone: [phone]
Fax: [phone]
Far East Office
Unit 5, 17/F, Metropole Square
2 On Yiu Street, Shatin
New Territories,
Hong Kong
(852) 2145-7118
Fax: [phone]
Internet Address: www.vicon-cctv.com