Vicon V2000B-BOX User manual

Waterproof Rubber Sealing
Holding Bracket Plate
Wall & Surface Mount with Junction Box Kit
V2000B-BOX
For V2000B Bullet & V2360W Panoramic
Cameras
Quick Guide
1. Product Overview
FIGURE 1-1: PHYSICAL DIMENSION
Screw & Waterproof Rubber Sealing Instruction
Since the junction box supports multiple devices, it is recommended
to review the following diagram carefully, which depicts different
screw types and waterproof rubber bushing for each device, prior to
installation.
FIGURE 1-2: SCREW TYPES ILLUSTRATION
FIGURE 1-3: WATERPROOF RUBBER BUSHING ILLUSTRATION
2. Installation and Mounting
Package Content
Check if all items listed below are included in the packing box.
⚫One adaptor plate
⚫Two waterproof bushings
⚫One holding bracket plate
⚫One junction box
⚫One torx wrench
⚫One mounting template
⚫One printed quick guide
⚫Six TP4 tapping screws
⚫Six screw anchors
⚫Three M2.6X5mm screws
⚫Four M4X5mm screws (for V2360W Panoramic)
⚫Six M4X14mm screws (for V2000B Bullet)
Required Tools
The following tools might help during the installation:
⚫A drill
⚫A hammer
⚫A Phillips head screwdriver
⚫Wire cutters
Installation & Mounting Procedure
1. Drill 6 holes on wall or surface based on the mounting
template. Diameter φ3/8” (9.5mm), depth 1/1/2” (40mm).
2. Hammer the 6 screw anchors into the drilled holes.
3. Fix the junction box onto the wall/surface by fastening the 6 TP4
tapping screws with the 6 screw anchors.
FIGURE 2-1: FIX JUNCTION BOX
3. Mounting Procedure
For IR Bullet Camera
1. Pass the camera cable through the adaptor plate, and then
secure the camera to the adaptor plate by fastening the 6
M4X14mm screws.
FIGURE 3-1: SECURE CAMERA WITH ADAPTOR PLATE
2. From the rear, cover the cable with the waterproof rubber
bushing and fasten them to the holding bracket plate using 3
M2.6X5mm screws onto the proper hole.
FIGURE 3-2: CABLE THREAD PREPARATION
3. Place thecable inside the junction box to connect with required
cables coming from either the bottom or side conduit hole of
the camera, depending on type of application, and attach the
junction box with the adaptor plate by fastening the
3 T20 screws with T20 torx wrench.
FIGURE 3-3: ASSEMBLE \JUNCTION BOX WITH ADAPTOR PLATE
4. Finally, install the mounting kit with camera onto a wall or
surface.
FIGURE 3-4: MOUNTING COMPLETE
Be sure that unused ¾ NPT hole
is sealed with the supplied cap.
Ø5.8 (147)
M4X5mm screw
M4X14mm screw
For V2360W
panoramic camera
(Recommended
cable diameter no
less than 5mm)
For V2000B bullet camera
Unit: in. (mm)
Ø5.8 (147)
2.4 (60)
Waterproof Rubber Bushing

For Panoramic Camera
1. Pass the camera cable through the adaptor plate and then
secure the cable with waterproof rubber bushing.
2. Fasten the waterproof rubber bushing to the holding bracket
plate with the 3 M2.6X5mm screws.
FIGURE 3-5: SECURE ADAPTOR PLATE ON JUNCTION BOX
3. Secure the adaptor plate on junction box by fastening with the
3 T20 screws T20 torx wrench.
FIGURE 3-6: SECURE ADAPTOR PLATE ON JUNCTION BOX
4. Secure the bracket on adapter plate by fastening the 4
M4X5mm screws, and then push the cable into junction box.
FIGURE 3-7: SECURE THE BRACKET ON ADAPTOR PLATE
Rotate panoramic camera to secure the screw on the bracket.
Then, rotate the T10 screw on panoramic camera
counterclockwise to make sure panoramic camera does not
rotate.
FIGURE 2-8: SECURE CAMERA ON BRACKET
Notes & Warnings
The holes for wall/surface mount are of diameter φ 10 mm. Use
screws of φ 8~9mm, and make sure the drilled holes are of
correct size to ensure proper installation.
When drilling the hole, make sure the wall/surface thickness is
greater than 50mm in order to maintain its structural integrity.
Make sure there are no damaged parts prior to assembly.
4. Specification
Material
Aluminum
Color
White
Dimensions (WxHxD)
5.8x5.8x2.4 in. (147x147x60 mm)
Weight
2.3 lb (0.85 kg)
Product specifications subject to change without notice.
Vicon part number: 8009-8318-90-00 10/2020
Copyright ©2020 Vicon Industries Inc. All rights reserved
Holding Bracket Plate
Waterproof Rubber Sealing
Waterproof Rubber Bushing