Viconics VTR8300 Series User manual

VTR8300 Series Installation Guide
Room Controller with Optional PIR sensor
Commercial and Hotel/Lodging HVAC Fan Coil Applications
CONTENTS
Installation 2
Location 2
Installation 2
Terminal, Identification and Function 3
Communication wiring to VC3xxxE Relay Pack 3
BACnet®Communication Wiring (if applicable) 3
Network wiring topology 3
How to Enter Setup Screen 4
Setup Screen Display 4
Specifications 5
Drawing and Dimensions 6
Version 5

2
Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: [phone] | Fax: [phone]
028-0414-05 www.viconics.com | [email protected] February 2018
DISCLAIMERS
• The VTR8300 series Room Controller is only to be used in conjunction with the VC3000 line voltage switching relay pack.
Together they are used as operating controls for high voltage fan coil units.
• If replacing an existing Line Voltage FCU Controller, label the wires before removal of the Room Controller.
• Electronic controls are static sensitive devices. Discharge yourself correctly before manipulating and installing the Room
Controller. A short circuit or wrong wiring may permanently damage the Room Controller or equipment.
• All VTR8300 series Room Controllers are designed for use as operating controls only and are not safety devices. These instruments
have undergone rigorous tests and verification prior to shipping to ensure proper and reliable operation in the field. Whenever
a control failure could lead to personal injury and/or loss of property, it becomes the responsibility of the user/installer/electrical
system designer to incorporate safety devices such as relays, flow switches, thermal protections, and/or an alarm system to
protect the entire system against any catastrophic failures. Tampering with the devices or unintended application of the devices
results in a void of warranty.
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be
impaired.
• These devices are not serviceable and must be returned to the supplier for any repair.
• A switch or circuit breaker must be installed. It must be suitably located, easily reached, and marked as the disconnecting
device
• Never apply more than 9VDC to Room Controller.
• This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
VTR8300 Room Controller VC3000 Relay Pack
IMPORTANT SYMBOLS
Products marked with this symbol state that the manuals must be consulted in all cases to any hazards.
This product has been tested to the requirements of CAN/CAS-C22.2 No. 61010-1, second edition, including Amendment
1, or a later version of the same standard incorporating the same level of testing requirements.
Alternating Current
Direct Current
Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION

3
Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: [phone] | Fax: [phone]
028-0414-05 www.viconics.com | [email protected] February 2018
INSTALLATION
Location
• Do not install on outside wall.
• Do not install in areas with direct heat source.
• Do no install near any air discharge grill.
• Do not install in areas exposed to direct sunlight.
• Ensure Room Controller has sufficient air circulation.
• Ensure wall surface is flat and clean.
Installation
1. Open unit by pulling on bottom side of Room Controller (Figure 1).
2. Read FCC ID and IC label installed in cover before installing any wireless
product.
3. Ensure correct side of base faces up.
4. Pull cables 6in (15cm) out from wall.
5. Align base and mark location of two mounting holes on wall (Figure 2).
6. Install anchors in wall.
7. Insert cable in central hole of base.
8. Insert screws in mounting holes on each side of base.
9. Strip each wire 1/4in ( 0.6cm) from end.
10. Insert each wire according to wiring chart (next page).
11. Gently push excess wiring back into hole.
12. Gently align cover to top of base and snap in place from bottom (Figure 3) .
13. Install security screw.
• If replacing an existing Line Voltage FCU Controller, label the
wires before removal of the controller.
• Electronic controls are static sensitive devices. Discharge
yourself properly before manipulating and installing the
Room Controller.
• A short circuit or wrong wiring may permanently damage the
Room Controller or the equipment.
• All VTR8300 series Room Controllers are designed for
use as operating controls only and are not safety devices.
Tampering with the devices or unintended application of
the devices will result in a void of warranty. This transmitter
must be installed to provide a separation distance of at least
4in (10cm) from all persons and must not be collocated
or operating in conjunction with any other antenna or
transmitter.
Figure-1 Open the cover
Figure-2 Install the base
Figure-3 Reinstall cover

4
Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: [phone] | Fax: [phone]
028-0414-05 www.viconics.com | [email protected] February 2018
To other
VC3xxxE
Relay
Pack
Terminal Controller
Relay Pack
VTR83xxA VC3504E
4 - Tx / Rx
5 - 7 Vdc Power Hot
6 - Power Common
1 - Tx / Rx
2 - 7 Vdc Power Hot
3 - Power Common
Relay Pack
VC3300E
1 - Tx / Rx
2 - 7 Vdc Power Hot
3 - Power Common
Terminal Controller
Terminal Controller
To others
To others
13 - COM +
14 - COM -
VTR83xxA VTR83xxA
13 - COM +
14 - COM -
Terminal Identification All VTR83xxA
Terminal Equipment Controller
Terminal 4 Tx – Rx Communication
Terminal 5 Power Hot 7.0 VDC
Terminal 6 Power Common
Terminal 12 Modulating 0-10 VDC output. See note below.
Terminal 13 BACnet +
Terminal 14 BACnet -
Terminal 15 BACnet REF
Terminal 16 BI 1 ( Configurable )
Terminal 17 BI 2 ( Configurable )
Terminal 18 Scom
TERMINAL, IDENTIFICATION AND FUNCTION
Only ONE VC3xxxE Relay Pack with remote
monitoring inputs can be used under a single
VTR83xxA Controller. All other slave units must be
VC3xxxE Relay Pack(s) WITHOUT remote inputs. A
maximum of 10 VC3xxxE Relay Packs can be used
for a single VTR83xxA Room Controller.
From VTR83xxA to first VC3xxxE Relay Pack
• Uses existing or new field wires
• A minimum of 3 wires are required 14-22 Ga,
Solid or Stranded, shield not necessary
From first VC3xxxE to all other slave
VC3xxxE Relay Pack(s)
• Uses existing or new field wires
• A minimum of 2 wires are required 14-22 Ga,
Solid
or Stranded
• Shield not necessary
• Connect only two wires: Tx/Rx (1) and Power
Common (3).
Daisy Chained Topology
Star Topology Mixed Daisy Chained & Star Topology
COMMUNICATION WIRING TO VC3XXXE RELAY PACK
Network Wiring Topology
BACnet®Communication Shielded Wiring (if required)
NOTE: See VTR8300 BACnet®integration manual for more details
NOTE: never use any terminal not mentioned in above table.
Terminal 12 (UO12) - 0-10 VDC Modulating
Output
This output is not used by the SER8300 internal
control logic. A Lua4RC is required to use this
terminal.
Example: UO12 (0 - 10 VDC) = PI_Cool (%) /10
ME.AO124=ME.AO22/10
Installation Note:
The maximum distance between the SER8300
Room Controller and the SC3000 relay pack is
recommended at 50ft (15m) or less.

5
Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: [phone] | Fax: [phone]
028-0414-05 www.viconics.com | [email protected] February 2018
HOME SCREEN DISPLAY
Note: User HMI is configurable and allows display functions such as Date, Time,
Humidity, Outdoor Temperature, Setpoint, and others to be enabled or disabled by
setting various parameters.
Time
System Status
Fan Status
Up Arrow
Increase Temperature Setpoint
Actual Setpoint
Down Arrow
Decrease Temperature
Setpoint
Help
Language Selection
Temperature Units
Fan Mode
Date
Occupancy Status
Indoor Temperature
Indoor Humidity
Outdoor Temperature
System Mode
Short Network
Message
Hospitality User Interface Shown

6
Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: [phone] | Fax: [phone]
028-0414-05 www.viconics.com | [email protected] February 2018
HOW TO ENTER SETUP SCREEN
SETUP SCREEN DISPLAY
Return to
home screen
General Note:
1/2 Setup
Network
Configuration
Setpoints - Display
Service View
Test Outputs
Language Selection
Adjustable parameter
Non-adjustable parameter
Touch and hold this point
for 3 seconds to enter setup mode
Note: If a configuration / installer
password is activated to prevent
unauthorised access to the
configuration menu parameters, a
password entry prompt will appear
to prevent access to the device
configuration components.
Discover Mode The Controller will
become discoverable on the wireless
ZigBee®network for 1 minute (this
button is hidden if ZigBee®settings are
not configured)
Enter BACnet®& ZigBee®network settings
Enter parameter configuration menu
Enter setpoint & display settings
Enter output testing mode
Enter status and service view
Enter setpoint & display settings
Enter language selection settings