ViewZ 22-INCH TFT-LCD User manual

22-INCH TFT-LCD
PUBLIC VIEW MONITOR
INSTRUCTION MANUAL
Please read this manual thoroughly before use, and keep it handy for future reference.

SAFETY INSTRUCTION ………………………………………………………….……
2 ~ 3
CAUTIONS ……………………………………………………………..........................
4
FCC RF INTERFERENCE STATEMENT …………………………….......................
5
CONNECTING WITH EXTERNAL EQUIPMENT ……………………………………
6
REMOTE FUNCTIONS …………………………………………………………………
7
CONTROLS AND FUNCTIONS ………………………………………………………..
8 ~ 23
MOUNTING GUIDE ……………………………………………………………………..
24
D-SUB CONNECTOR PIN ASSIGNMENTS …………………………………………
25
POWER MANAGEMENT ………………………………………………………………
26
SPECIFICATIONS ………………………………………………………………………
27 ~ 30
TROUBLE SHOOTING GUIDE ………………………………………………….........
31
INSTRUCTION MANUAL ………………………………………………………………………. 1
This Monitor was
Manufactured by ISO 9001
Certified Factory

Important Safety Instruction
1. Read these instructions.
2. Keep these Instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers,stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
Apolarized plug has two blades with one wider than the other.
Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the bsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles and the point where they exit from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus the apparatus has been exposed to
rain or moisture does not operate normally or has been dropped.
2 ………………………………………………………………………. INSTRUCTION MANUAL

- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed no the apparatus.
14 Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.
“WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”
“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.”
This symbol is intended to alert the user to the presence of uninsulated :
dangerous voltage with in the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating
and maintenance(servicing) instructions in the literature accompanying the
appliance.
INSTRUCTION MANUAL ………………………………………………………………………. 3

CAUTION
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.
ATTENTIONN
Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être
située ou installée à proximité du matériel et être facile d`accès
▶NEVER REMOVE THE BACK COVER
Removal of the back cover should be carried out only by qualified personnel.
▶DO NOT USE IN HOSTILE ENVIRONMENTS
To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to vibrations,
dust of corrosive gases.
▶KEEP IN A WELL VENTILATED PLACE
Ventilation holes are provided on the cabinet to prevent the temperature from rising.
Do not cover the unit or place anything on the top of unit.
▶AVOID HEAT
Avoid placing the unit in direct sunshine or near a heating appliance.
▶TO ELIMINATE EYE FATIGUE
Do not use the unit against a bright back ground and where sunlight or other light sources will
shine directly on the monitor.
▶BE CAREFUL OF HEAVY OBJECT
Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.
4 ………………………………………………………………………. INSTRUCTION MANUAL

NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by
the grantee or manufacturer could void the users authority to operate such equipment.
▶DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulation of Canadian Department of
communications.
INSTRUCTION MANUAL ………………………………………………………………………. 5

A. TOP PANEL CONTROL
A-1. AC IN Type
1. DC 12V IN
2. HDMI IN
3. DVI IN
5. PC STEREO IN
7. S-VIDEO (Y/C) IN
10. CAMERA OUT
11. AV2 (VIDEO2) IN
13. AC IN
15. SD CARD READER (Optional)
A-2. AC 24V IN Type
4. VGA (D-SUB) IN
6. AUDIO OUT (Speaker)
8 & 9. AUDIO IN(R+L) for AV1, AV2
and S-VIDEO
12. AV2 (VIDEO2) OUT
14. USB 2.0 (Optional)
1. DC 12V IN
2. HDMI IN
3. DVI IN
5. PC STEREO IN
7. S-VIDEO (Y/C) IN
10. CAMERA OUT
11. AV2 (VIDEO2) IN
13. AC 24V IN
15. SD CARD READER (Optional)
4. VGA (D-SUB) IN
6. AUDIO OUT (Speaker)
8 & 9. AUDIO IN(R+L) for AV1, AV2
and S-VIDEO
12. AV2 (VIDEO2) OUT
14. USB 2.0 (Optional)
6 …………………………………………….……………………………INSTRUCTION MANUAL
14
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
10
11
12
13

B. REMOTE CONTROLLER(Optional)
1. POWER( )
Turns the power ON or OFF. There will be a few
seconds delay before the display appears.
2. SOURCE
Selects pc or video( AV1/AV2/S-Video/DVI/PC) sources.
3. AUTO
Auto geometry adjustment in PC Source.
4. MUTE
Mute the sound.
5. MENU
Activates and exits the On Screen Display.
6. EXIT
Exits the On Screen Display.
7. VOL(◀▶)
Increases or decreases the level of audio volume.
8. UP/DOWN
Moves to OSD menu.
9. ENTER
Accepts your selection or displays the current mode.
10. INFO
Input mode information Display.
11. STILL
Pauses the picture.
12. PIP (Picture In Picture)
Activates PIP mode.
13. P.INPUT
Selects PC or video source.
14. P.POS
Moves the position of sub picture for PIP mode.
15. P.SIZE
Changes the size of sub and main picture for PIP mode.
16. SWAP
Alternates between main and sub picture.
17. ARC (Aspect Ratio Control)
Selects screen ratio.
18. APC (Auto Picture Control)
Selects picture mode.
19. ACC (Auto Color Control)
Selects Color mode.
20. S.SET
Selects Sound mode main input or sub input
21. PC
Selects PC mode(PC,DVI)
22. AV
Selects AV mode.(AV1,AV2,S-VIDEO)
23. COMP
Selects COMPONENT mode.
24. SETUP
It doesn’t have any functions.
25. M/P on/off
Turns the M/P(Media Player) on or off.
26. SEL
Accepts your selection in the menu of M/P(Media Player).
27. ESC
Escapes the menu of M/P(Media Player).
28. ◀▲ ▶▼
Moves the cursor in the menu of M/P(Media Player).
INSTRUCTION MANUAL ………………………………………………………………………. 7

C. FRONT & BACK KEY CONTROL
1. PIR(Passive Infra-Red) Sensor
Built-in PIR(Passive Infra-Red) Sensor for the Motion Detection function.
2. BUILT-IN CAMERA
Image of this camera is shown by AV1.
3. IR Sensor
Remote controller sensor.
4. POWER LED
The power LED lights with green when the power is turned ON.
The power is turned off by pressing the power switch again and the power LED goes to off.
5 & 6. VOL(+) & VOL(-)
Adjust the volume and menu settings.
7 & 8. ▲& ▼
These buttons allow user to enter the sub-menu of the activated function.
The up(▲) button is HOLD function and stop the Motion Detection & Auto switching functions.
9. SOURCE/SELECT
Selects an input source.
Enters a submenu or accepts your selection in the OSD menu.
10. MENU/EXIT
Activates and exits the On Screen Display.
This button can also be used to move previous menu or status.
11. POWER ON/OFF( /I)
Turns the power ON or OFF. There will be a few seconds delay before the display appears.
8 ………………………………………………………………………. INSTRUCTION MANUAL
5
6
7
8
9
11
2
3
4
1
10