Vimar ELVOX 46322.003 User manual

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ISO14001
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert
the user to the presence of uninsulated dangerous voltage within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a Class
Adigital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at their own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
☞Do NOT use power sources other than those specified.
This installation should be made by a qualified service person and should conform to all
local codes.
2. Safety Instructions
• This camera should be installed by qualified personnel only
• There are no user serviceable parts inside
• Do not disassemble this camera other than to make initial adjustments
• Use a UL approved regulated 24 voltAC or 12 volt DC power supply
• Use appropriate low voltage power cable to prevent fire or electrical shock
• Please insure that your installation area can support the weight of the camera
• Do not use a strong or abrasive detergent when cleaning the camera
• Do not expose the camera to direct sun
• Do not install camera in places where humidity is high
• Do not install near cooling or heating device
• Do not expose camera to rain or moisture
Precautions for use
Please handle this camera carefully
1. Precautions
Do not install the camera in extreme
temperature conditions.
Do not touch the front lens of the camera.
Do not expose the camera to rain or spill
liquids on it.
Do not install or use the camera in an
environment where the humidity is high.
Do not install or use the camera in an
environment where the humidity is high.
Never keep the camera pointed directly
at strong light.
Do not expose the camera to radioactivity.
Do not install the camera under unstable
lighting conditions.
Do not drop the camera or subject it to
physical shocks.
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially careful
to provide ventilation when operating
under high temperatures.
This is one of the most important parts
of the camera. Be careful not to leave
fingerprints on the lens cover.
If it gets wet, wipe dry immediately.
Liquids can contain minerals that
corrode the electronic components.
It can cause malfunctions to occur.
If exposed to radioactivity the CCD will
fail.
Severe lighting change or flicker can
cause the camera to work improperly.
Housing damage can compromise
weatherproof ratings.
NOTE
* If the camera is exposed
to spotlight or object
reflecting strong light,
smear or blooming may
occur.
* please check that the
power satisfies the normal
specification before
connecting the camera.
Installation and operation manual
CCTV S6I.46322.003.EN RL. 00 13 03
ELVOX - Campodarsego - Italy
Via Pontarola, 14/a
35011 Campodarsego PD - Italy
Tel. [phone]
Fax [phone]
www.elvox.com
46322.003
HD-SDI fullHD MiniDome Camera, 4mm Lens
CCTV CCTV
EN EN
CCTV

CCTV CCTV
EN EN
CCTV CCTV
EN EN
L-WRENCH
1EA SCREW 3EA
8. Package
4. Key Features
5. Specifications
6. Cable Connection
7. Camera Connection
3. Dimension
• 1/2.8” Sony Progressive Scan Color CMOS Sensor
• 1080(1920x1080)@25fps
• TV Out(BNC) With NTSC / PAL Selectable
• Dual Output-Megapixel HD CCTV(BNC) & SD CCTV(BNC) Out
• Backlight Compensation Using a Powerful Pixel Control WDR
• Flicker suppression
• No noise, Ghosting Effect With DNR
• Power DC 12V
54 54
MODEL 46322.003
Image Sensor
Scanning System
High Speed
ShutterResolution
Pixels - total
Pixels - Effective
Sensitivity Colour
Sentitivity B&W
S/N Ratio
Lens Focal
LengthOperating
TemperatureStorage
TemperatureHumidity
Supply Voltage
Power
ConsumptionDimension
Weight
1/2.8" SONY 2Mega C-MOS Sensor
progressive 25fps
1/25~ 1/60.000 sec, AUTO
1080P
2010(H) X 1092(V) 2.22Mega Pixel
1944(H) X 1092(V) 2.12Mega Pixel
0.5 Lux @ F1.2 , 0.01 Lux(SENS-UP X64)
0.3 Lux @ F1.2 , 0.001 Lux(SENS-UP X64)
50 dB
2.97mm Fixed Board Lens
-10°C ~ +50°C
-20°C ~ +60°C
less than 85%
DC 12V
150mA
54mm(W) * 50mm(H) * 54mm(D)
300g
54 54
SDI Signal
SDI
2.97mm Fixed Borad Lens
Camera
1EA
*2.97mm Fixed Board Lens
Digital Video Security System