Vintec VWCM280CAB-L User manual

User Manual
VWCM280CAB-L, VWCM280CAB-R
vintec.com.au / vintec.co.nz

2
User Manual

Contents
Warning ......................................................3
Before use ..................................................7
Reduction in energy consumption ..............7
Get to know your wine cabinet ...................8
Electrical connection...................................9
Installation and start-up ..............................9
Installation ................................................10
Shelves and loading .................................12
Shelf adjustment.......................................13
Operation and function .............................15
Defrosting, cleaning and maintenance .....20
Fault nding ..............................................21
Disposal....................................................22
3
User Manual

As the appliance contains a
ammable refrigerant, it is es-
sential to ensure that the refrig-
erant pipes are not damaged.
The quantity and type of the
refrigerant used in your appli-
ance is indicated on the rating
plate.
Standard EN378 species that
the room in which you install
your appliance must have a
volume of 1m³ per 8g of hydro-
carbon refrigerant used in the
appliances. This is to avoid the
formation of ammable gas/air
mixtures in the room where the
appliance is located in the event
of a leak in the refrigerant circuit.
WARNING:
Keep ventilation openings in
the appliance’s cabinet or in the
built-in structure clear of obstruc-
tion.
WARNING:
Do not use mechanical devices
or other means to accelerate the
defrosting process than those
recommended by the manufac-
turer.
WARNING:
Do not damage the refrigerant
system.
WARNING:
Do not use electrical applianc-
es inside the refrigerated stor-
age compartment, unless they
are of a type recommended by
the manufacturer.
WARNING:
This appliance is suitable for
indoor use only. Do not expose
the appliance to rain.
WARNING:
This appliance is not intended
for use by persons (including
children) with reduced physical,
sensory or mental capabilities,
or lack of experience and knowl-
edge, unless they have been
given supervision or instruction
concerning use of the appliance
by a person responsible for their
safety. Children should be super-
vised to ensure that they do not
play with the appliance.
WARNING:
Children must not clean the
appliance or carry out general
Warning
4
User Manual

maintenance unless they are at
least 8 years old and are being
supervised.
WARNING:
Children must not play with, on,
or around the appliance.
WARNING:
This appliance contains insula-
tion formed with ammable blow-
ing gases. Avoid safety hazards
by carefully disposing of this
appliance.
WARNING:
Do not store explosives, such
as aerosol cans with ammable
propellants in the appliance.
WARNING:
When this symbol is used, it in-
dicates ammable materials are
used. To avoid relevant hazards,
it is required to carefully dispose
of this appliance.
!R600A REFRIGERANT WARN-
ING:
This appliance contains R600a
refrigerant. Avoid safety hazards
by carefully installing, handling,
servicing and disposing of this
appliance.
●It is hazardous for anyone oth-
er than an Authorised Service
Person to service this appli-
ance. In Queensland – the au-
thorised Service Person MUST
hold a Gas Work Authorisation
for hydrocarbon refrigerants, to
carry out Servicing or repairs
which involve the removal of
covers.
●Ensure that the tubing of the
refrigerant circuit is not dam-
aged during transportation and
installation.
WARNING:
When positioning the appliance,
ensure the power cord is not
trapped or damaged.
WARNING:
Do not locate multiple portable
socket-outlets or portable power
supplies at the rear of the appli-
ance.
WARNING:
If the power cord is damaged, it
must be replaced by the manu-
5
User Manual

facturer, its service agent or
similarly qualied persons in
order to avoid a hazard (For
Australia and New Zealand).
●Always keep the keys in a
separate place and out of
reach of children.
●Before servicing or cleaning
the appliance, unplug the ap-
pliance from the mains or dis-
connect the electrical power
supply.
●Frost formation on the interior
evaporator wall and upper
parts is part of normal opera-
tion. Therefore, the appliance
may need to be defrosted dur-
ing normal cleaning or mainte-
nance.
●Please note that changes to
the appliance construction
may cancel all warranty and
product liability.
●If the supply cord is dam-
aged, it must be replaced by
the manufacturer, its service
agent, or similarly qualied
persons inorder to avoid a
hazard.
●Do not use extension cords
●This appliance is intended to
be used exclusively for the
storage of wine.
●It is normal for some conden-
sation to appear on the inside
of the door when the product
is opened in certain ambient
conditions. This condensation
should disappear after a time
when the product is operating.
CLASS 1 LED PRODUCT
WARNING:
LED lighting
Your appliance is tted with long
life LED lighting. In the unlikely
event the LED lights should fail,
then the LED lights should be
serviced by the service agent,
to avoid a safety hazard. Refer
to the warranty page for contact
details.
6
User Manual

On receipt, check to ensure that the appli-
ance has not been damaged during trans-
port. Transport damage should be reported
to the local distributor before the wine
cooler is put to use. Do not remove glass
door tapes until the unit is positioned at its
nal location (see label at the glass door).
Remove the packaging. Clean the inside of
the cabinet using warm water with a mild
detergent. Rinse with clean water and dry
thoroughly (see cleaning instructions). Use
a soft cloth.
If during transport the appliance has been
laid down, or if it has been stored in cold
surroundings (colder than + 5°C), it must be
allowed to stabilise in an upright position for
at least 24 hour before being switched on.
Before use
●the lower the ambient temperature.
●the warmer thermostat set point.
●the lower the number and the shorter the
length of the door openings.
The energy consumption is reduced when:
Note: for household use only
This appliance is intended to be used in
household and similar applications such as
● sta󰀨 kitchen areas in shops, o󰀩ces and
other working environments;
●farm houses and by clients in hotels,
motels and other residential type environ-
ments;
●bed and breakfast type environments;
●catering and similar non-retail applica-
tions.
Important Information that may
impact your Manufacturer’s
Warranty
Adherence to the directions for use in this
manual is extremely important for health
and safety. Failure to strictly adhere to the
requirements in this manual may result in
personal injury, property damage and af-
fect your ability to make a claim under the
Vintec manufacturer’s warranty provided
with your product. Products must be used,
installed and operated in accordance with
this manual. You may not be able to claim
on the Vintec manufacturer’s warranty in the
event that your product fault is due to failure
to adhere to this manual.
7
User Manual

Get to know your wine cabinet
VWCM280CAB-L ,VWCM280CAB-R
g.2
Control panel
Fans
Positions 1-6
Fixed shelves
Wheel
Adjustable feet
Name plate
Lock
Lighting
Door
Sealing strip
8
User Manual

Placement
For safety and operational reasons, the ap-
pliance must not be installed outdoors.
The appliance should be placed on a level
surface in a dry, well ventilated room (max.
75% relative air humidity). Never place the
appliance close to sources of heat such as
cookers or radiators, and avoid placing it in
direct sunlight.
Climate class is stated on the name plate.
This species the optimum ambient tem-
perature.
Installation and start-up
Electrical connection
g.3
Wiring and connections in power supply
systems must meet all applicable (local and
national) electrical codes. Consult these
codes prior to cabinet installation.
Connect the appliance only to 220/240 V
/ 50Hz alternating current via a correctly
installed earthed socket.
The socket should be freely accessible.
Information regarding voltage, current or
power are given on the rating plate
The power cord may be replaced by a
technician only.
CAUTION: Never put the appliance in a
location that is too cold or unprotected, for
example in a garage or on a verandah.
The rating plate provides various techni-
cal information as well as type and serial
number.
Climate class Optimum room
temperature
SN +10 ºC to +32 ºC
N +16 ºC to +32 ºC
ST +18 ºC to +38 ºC
T +18 ºC to +43 ºC
Max ambient temperature class
Class 3 25 ºC
Class 4 30 ºC
Class 5 40 ºC
Class 7 35 ºC
9
User Manual

The surface on which the appliance is to
be placed must be level. Do not use a
frame or similar.
The appliance can be installed as a free-
standing unit against a wall, built into a
closet or lined up with other appliances.
It is important that the appliance be well
ventilated and that air can circulate un-
hindered above, below and around it.
The gures below illustrate how the
necessary air circulation around the ap-
pliance can be ensured (g 4).
Ensure the socket is accessible when
the appliance is in position, or a switch is
incorporated in the xed wiring accord-
ing to the wiring rules. (See a licensed
electrician for further advice).
g. 4
g. 5
Installation
10
User Manual

g. 6
Anti-tip
It is recommended to install the supplied
anti-tip device to avoid the unit from tipping
over.
The appliance must be securely attached to
the wall by the anti-tip bracket device. The
hardware used to secure your appliance to
the wall depends on your wall material and
will need to be sourced separately to suit
the specic installation.
Use gloves during installation.
If there is not enough space (min 60 mm)
over the appliance turn the bracket upside
down.
Setting up
It is important that the appliance be abso-
lutely level. It can be levelled by screwing
the adjustable feet at the front of the appli-
ance up or down (g. 7).
Use a spirit level to check that the appliance
is absolutely level sideways.
g. 7
11
User Manual

12
User Manual
Fixed shelf - VWCM280CAB-L; VWCM280CAB-R
Max. 60 kg.
Shelves and loading
To optimise the storage capacity of your
wine cabinet it has been designed so that
only Bordeaux style bottles can be stored
on the outer position of the shelf.
The xed shelf in the VWM280CAB cabinet
is designed for 3 or 4 rows of 12 bottles (36
or 48 bottles). However 4 rows will result
in approximately 3 mm deection which is
normal and will not damage the shelf.
g. 9
g. 8
40
60

To remove the x shelves:
1. Open door to fully 135°.
2. Remove all wine bottles from the shelf.
3. Remove the back locker pin on both side. It is accessible by nger. Pull forward and push
up.
4. Use a thin at screwdriver to snap out the xation clipse and push up the holder in the
meantime. 4 piece of holder per shelf.
To replace the x shelves:
Replace is a back way process:
1. Push in and down the plastic shelf holder to the square holes. Watch the xation clips to
ensure the holder is into the right and x position. 4 piece of holder per shelf.
In order to easy repositioning use the positioning holes on the side wall.
g. 10
g. 11
g. 12
13
User Manual
Shelf adjustment

2. put back the shelf to the holders and check the shelf level and plane with care. If you en-
sured the shelf is in good position than replace back the two shelf backside xation clips and
push it down (you will hear when it snaped in)
To remove the telescoping shelves:
1. Open door to fully 135°.
2. Remove all wine bottles from the shelf.
3. Fully extend the shelf.
4. Using a TX20 head screwdriver, remove the 2 rail-shelf screws (1 per rail).
5. Pull forward the shelf and lift up it.
6. Use a thin at screwdriver to snap out the locker clipse and push up the rail in the mean-
time. Front and back of the rail on both side of cabinet.
To replace the telescoping shelves:
Replace is a back way process:
1. Reposition the rail.
2. Align in the clips to the side wall square holes
and push it down.
In order to easy repositioning use the positioning
holes on the side wall.
Take care to reposition the same level the two end
and the both side.
g. 14
g. 15
g. 13
14
User Manual

Operation and function
g. 16
Electronic control
The electronic control ensures that the
temperatures set at the top and at the bot-
tom of the appliance are maintained. This is
achieved by means of an advanced control
of the refrigeration system, the heating ele-
ment, and the fan. The set temperature will
be stored in the event of power failure.
The electronic control has the following
functions:
●Light switch *
●Temperature setting
●Temperature indication
●Alarm for too high and too low tempera-
tures
● Door alarm / Filter alarm
● Muliti / Single / Cellar mode
●Child lock
●Sabbath mode
* The light may either be turned on
constantly or only when the door is open.
4 di󰀨erent modes- 9 levels for lighting.
Temperature indication
The display shows the actual temperature.
The left digits of the display indicate the
temperature at the top of the appliance, and
the right digits of the display indicate the
temperature at the bottom of the appliance.
Upper temperature set
Single press the up or down arrow to de-
crease/increase the Set
temperature. First press shows the current
Set temperature and don’t increase/de-
crease it. The numbers blink to indicate that
they are being changed. After 5 seconds
without any interaction with the “-/+”, the
numbers stop blinking and show the Cur-
rent temperature.
Bottom temperature set
Single press the up or down arrow to de-
crease/increase the Set
temperature. First press shows the current
Set temperature and don’t increase/de-
crease it. The number blinks to indicate that
it is being changed. After 5 seconds without
any interaction with the “-/+”, the numbers
stop blinking and show the Current tem-
perature.
Mode Set temp. Upper temp. Bottom temp.
Alerts Set temp. Light
Upper zone Bottom zone.
15
User Manual

Lights On/O󰀨
Single press to turn the lights ON/OFF.
If O󰀨, the light is always o󰀨 (door opened or
closed). If On, light behaviour goes to previ-
ous setting )1A-4A/ 1L-9L).
Lights settings menu
Press & Hold for 3 seconds to enter/exit
Lights settings menu.
Both temperature displays blink and show a
specic code.
Single press to increase/decrease the
“level”.
S
M
WIP
1.1 On/ O
1.1 Upper t emper atur e set
1.2 Button temper atur e set
1.3 Light s On/ O
Single pr ess to decr ease /incr ease the Set
temper ature. Fir st press sho ws the curr ent Set
temper ature and don’t incr ease /decr ease it .
The number s blink to indicat e that is being
change . After 5 seconds without any interaction
with the “-/+”, the number s stop blink and sho w
the Curr ent temper ature.
Single pr ess to decr ease /incr ease the Set
temper ature. Fir st pr ess sho ws the curr ent Set
temper ature and don’t incr ease /decr ease it .
The number s blink to indicat e that is being
change . After 5 seconds without any interaction
with the “-/+”, the number s stop blink and sho w
the Curr ent temper ature.
Single pr ess to turn ON/ OFF
2.1 Lights settings menu
Press&Hold fo r 3 seconds to enter/e xit Lights
settings menu .
Both temper ature displays blink and sho w a
specific code .
Any alert turns o tempor arily.
Single pr ess to increase /decr ease the “leve l”
Lights behaviour
Upper temp . display sho ws the, E. g.:
1A:All lights alw ays On
2A: Door lights only On when door is open
3A: Dim lights to the lo we st level aft er 5 min with
the door closed.
4A: et c.
Lights dim le ve l
Bott om temp . display sho ws the, E. g.:
1L:Lo we st level / leas t bright
2L:...
...
9L: Highest le vel / most bright
Single pr ess to turn the lights ON/ OFF
Quick e xplanation of the UI behaviour . A mor e detail specification will be pr ovided
later , after the definition of the functionalities and the feasibility check. 2018.10.0
Vintec - Ve stfros t UI Pr oposal
Lights behaviour
Upper temp. display shows the, di󰀨erent
light mode.
1A: Lights always ON at highest dim level
when door is open. Changing to the se-
lected dim level immediately when the door
is closed (500ms).
2A: Lights always ON at highest dim level
when door is open (500ms) Turning OFF
immediately when the door is closed
(500ms).
3A: Lights always ON at selected dim level
when door is open and closed.
4A: Lights always ON at selected dim level
when door is open (500ms) changing to the
highest dim level when the door is closed
(500ms).
Default Factory settings:
Light Behavior: 1A
Dim Level: 9L
S
M
WIP
1.1 On/ O
1.1 Upper t emper atur e set
1.2 Button temper atur e set
1.3 Light s On/ O
Single pr ess to decr ease /incr ease the Set
temper ature. Fir st pr ess sho ws the curr ent Set
temper ature and don’t increase /decr ease it .
The number s blink to indicat e that is being
change . After 5 seconds without any inter action
with the “-/+”, the number s stop blink and sho w
the Curr ent temper ature.
Single pr ess to decr ease /incr ease the Set
temper ature. Fir st pr ess sho ws the curr ent Set
temper ature and don’t increase /decr ease it .
The number s blink to indicat e that is being
change . After 5 seconds without any inter action
with the “-/+”, the number s stop blink and sho w
the Curr ent temper ature.
Single pr ess to turn ON/ OFF
2.1 Lights settings menu
Press&Hold fo r 3 seconds to enter/e xit Lights
settings menu .
Both temper ature displays blink and sho w a
specific code .
Any alert turns o tempor arily .
Single pr ess to increase /decr ease the “leve l”
Lights behaviour
Upper temp . display sho ws the, E. g.:
1A:All lights alw ays On
2A: Door lights only On when door is open
3A: Dim lights to the lo we st level aft er 5 min with
the door closed.
4A: et c.
Lights dim le ve l
Bott om temp . display sho ws the, E. g.:
1L:Lo we st level / leas t bright
2L:...
...
9L: Highest level / most bright
Single pr ess to turn the lights ON/ OFF
Quick e xplanation of the UI behaviour . A more detail specification will be pr ovided
later , after the definition of the functionalities and the feasibility check. 2018.10.0
Vintec - Ve stfros t UI Pr oposal
Lights dim level
Bottom temp. display shows the, light level
1L: Lowest level / least bright
2L:...
9L: Highest level / most bright
Child Lock
Press & Hold for 3 seconds on Mode to
activate/deactivate child lock.
S
M
WIP
2.2 Child L ock
Single combined pr ess on incr ease and
decr ease upper temper ature set to
activ ate/ deactiv ate child lock.
Child lock fe edback. It lit-up when Child lock is
activ ated .
Relat ed to 3. 4
2.4 C°/F° set
Single combined pr ess on decr ease bott om
temper ature set & Light button to change the
temper ature type ( C°/F°) .
2.3 Sabbath mode
S
M
Press&Hold combined on incr ease bott om
temper ature set & Light buttons fo r 5 seconds
to activ ate/ deactiv ate Sabbath mode .
When activ ated, Bott om & Upper temper atur e
displays sho w and blinks “Sb ” & “On” fo r 5
seconds until the it be deactiv at ed . In this state:
- Any button command is disabled apart from
the incr ease bott om temper ature set & Light
combination command to deactiv at e the
Sabbath mode .
- All lights ar e turned O - apart from “Sb” &
“On”- , all sounds ar e muted .
- Opening or closing the door will not directly
turning on or o any lights, digital r eadouts,
solenoids, fans, valves, compr essor , icons, tones,
or alarms.
- All alerts will not be display ed until the
Sabbath Mode is deactiv at ed, ex cept by the
High/L ow Temper atur e alerts.
S
M
When C° is set , Bott om & Upper temper ature
display sho ws and blinks “C°” & “C°” fo r 5
seconds.
Any alert turns o tempor arily.
S
M
When F° is set , Bott om & Upper temper ature
display sho ws and blinks “F°” & “F°” for 5
seconds.
Any alert turns o tempor arily.
S
M
When deactiv at ed, Bott om & Upper temper a-
ture displays sho w and blinks “Sb ” & “OF” for 5
seconds.
Ex ception:
The High/L ow Temper atur e alerts will be
display ed in case of high or low temper atur e
inside the appliance . The alert icon turns On, but
will not blink, and it will remain until the Sabbath
Mode is deactiv ated. An audio alarm will
sounds and aut omatically turn o after 10
minutes .
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
Child lock feedback. It lit-up when Child lock
is activated.
Sabbath mode Activation
S
M
WIP
2.2 Child L ock
Single combined pr ess on incr ease and
decr ease upper temper ature set to
activ ate/ deactiv ate child lock.
Child lock fe edback. It lit-up when Child lock is
activ ated .
Relat ed to 3. 4
2.4 C°/F° set
Single combined pr ess on decr ease bott om
temper ature set & Light button to change the
temper ature type ( C°/F°) .
2.3 Sabbath mode
S
M
Press&Hold combined on incr ease bott om
temper ature set & Light buttons for 5 seconds
to activ ate/ deactiv ate Sabbath mode .
When activ at ed, Bott om & Upper temper ature
displays sho w and blinks “Sb ” & “On” for 5
seconds until the it be deactiv ated . In this stat e:
- Any button command is disabled apart from
the incr ease bott om temper ature set & Light
combination command to deactiv at e the
Sabbath mode .
- All lights ar e turned O - apart from “Sb ” &
“On”- , all sounds ar e mut ed .
- Opening or closing the door will not directly
turning on or o any lights, digital r eadouts,
solenoids, fans, valv es, compr essor , icons, tones,
or alarms.
- All alerts will not be display ed until the
Sabbath Mode is deactiv ated, ex cept by the
High/L ow Temper atur e alerts.
S
M
When C° is set , Bott om & Upper temper atur e
display sho ws and blinks “C°” & “C°” for 5
seconds.
Any alert turns o tempor arily .
S
M
When F° is set , Bott om & Upper temper atur e
display sho ws and blinks “F°” & “F°” fo r 5
seconds.
Any alert turns o tempor arily .
S
M
When deactiv at ed, Bott om & Upper temper a-
ture displays sho w and blinks “Sb” & “OF” for 5
seconds.
Ex ception:
The High/L ow Temper atur e alerts will be
display ed in case of high or lo w temper atur e
inside the appliance . The alert icon turns On, but
will not blink, and it will remain until the Sabbath
Mode is deactiv at ed. An audio alarm will
sounds and aut omatically turn o after 10
minutes.
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
Press&Hold simultaneously the increase
top temperature arrow and the decrease
bottom temperature arrow for 5 seconds.
When activated, Bottom & Upper temper
displays shows and blinks “Sb” & “On” for 5
seconds and then shows "Sb" & "On" till the
Sabbath mode is deactivated.
All button commands are disabled except
the increase top temperature and decrease
bottom temperature combination command
used to deactivate the Sabbath mode.
All alerts will not be displayed until the Sab-
bath Mode is deactivated, except the
16
User Manual

High/Low Temperature alert. This alert will
display in case of a high or low temperature
inside the appliance. The alert icon will turn
on, but will not blink and will remain on till
Sabbath mode is deactivated. An audio
alarm will sound for 10 minutes and will
then shut o󰀨 automatically.
Sabbath mode deactivation
S
M
WIP
2.2 Child L ock
Single combined pr ess on incr ease and
decr ease upper temper ature set to
activ ate/ deactiv ate child lock.
Child lock fe edback. It lit-up when Child lock is
activ ated .
Relat ed to 3. 4
2.4 C°/F° set
Single combined pr ess on decr ease bott om
temper ature set & Light button to change the
temper ature type ( C°/F°) .
2.3 Sabbath mode
S
M
Press&Hold combined on incr ease bott om
temper ature set & Light buttons for 5 seconds
to activ ate/ deactiv ate Sabbath mode .
When activ at ed, Bott om & Upper temper ature
displays sho w and blinks “Sb ” & “On” for 5
seconds until the it be deactiv ated . In this stat e:
- Any button command is disabled apart from
the incr ease bott om temper ature set & Light
combination command to deactiv at e the
Sabbath mode .
- All lights ar e turned O - apart from “Sb ” &
“On”- , all sounds ar e mut ed .
- Opening or closing the door will not directly
turning on or o any lights, digital r eadouts,
solenoids, fans, valv es, compr essor , icons, tones,
or alarms.
- All alerts will not be display ed until the
Sabbath Mode is deactiv ated, ex cept by the
High/L ow Temper atur e alerts.
S
M
When C° is set , Bott om & Upper temper atur e
display sho ws and blinks “C°” & “C°” for 5
seconds.
Any alert turns o tempor arily .
S
M
When F° is set , Bott om & Upper temper atur e
display sho ws and blinks “F°” & “F°” fo r 5
seconds.
Any alert turns o tempor arily .
S
M
When deactiv at ed, Bott om & Upper temper a-
ture displays sho w and blinks “Sb” & “OF” for 5
seconds.
Ex ception:
The High/L ow Temper atur e alerts will be
display ed in case of high or lo w temper atur e
inside the appliance . The alert icon turns On, but
will not blink, and it will remain until the Sabbath
Mode is deactiv at ed. An audio alarm will
sounds and aut omatically turn o after 10
minutes.
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
Repeat the steps used for activation.
Upper and Lower temperature displays will
blink "Sb" & "Of" for 5 seconds and then the
displays revert to normal.
°C/°F set
Single combined press on increase bottom
temperature set & Light button to change
the temperature type (°C/F°).
S
M
WIP
2.2 Child L ock
Single combined pr ess on incr ease and
decr ease upper temper ature set to
activ ate/ deactiv ate child lock.
Child lock fe edback. It lit-up when Child lock is
activ ated .
Relat ed to 3. 4
2.4 C°/F° set
Single combined pr ess on decr ease bott om
temper ature set & Light button to change the
temper ature type ( C°/F°) .
2.3 Sabbath mode
S
M
Press&Hold combined on incr ease bott om
temper ature set & Light buttons for 5 seconds
to activ ate/ deactiv ate Sabbath mode .
When activ at ed, Bott om & Upper temper ature
displays sho w and blinks “Sb ” & “On” for 5
seconds until the it be deactiv ated . In this stat e:
- Any button command is disabled apart from
the incr ease bott om temper ature set & Light
combination command to deactiv at e the
Sabbath mode .
- All lights ar e turned O - apart from “Sb ” &
“On”- , all sounds ar e mut ed .
- Opening or closing the door will not directly
turning on or o any lights, digital r eadouts,
solenoids, fans, valv es, compr essor , icons, tones,
or alarms.
- All alerts will not be display ed until the
Sabbath Mode is deactiv ated, ex cept by the
High/L ow Temper atur e alerts.
S
M
When C° is set , Bott om & Upper temper atur e
display sho ws and blinks “C°” & “C°” for 5
seconds.
Any alert turns o tempor arily .
S
M
When F° is set , Bott om & Upper temper atur e
display sho ws and blinks “F°” & “F°” fo r 5
seconds.
Any alert turns o tempor arily .
S
M
When deactiv at ed, Bott om & Upper temper a-
ture displays sho w and blinks “Sb” & “OF” for 5
seconds.
Ex ception:
The High/L ow Temper atur e alerts will be
display ed in case of high or lo w temper atur e
inside the appliance . The alert icon turns On, but
will not blink, and it will remain until the Sabbath
Mode is deactiv at ed. An audio alarm will
sounds and aut omatically turn o after 10
minutes.
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
When °C is set, Bottom & Upper tempera-
ture display shows and blinks °C & °C for 5
seconds.
Any alert turns o󰀨 temporarily.
S
M
WIP
2.2 Child L ock
Single combined pr ess on incr ease and
decr ease upper temper ature set to
activ ate/ deactiv ate child lock.
Child lock fe edback. It lit-up when Child lock is
activ ated .
Relat ed to 3. 4
2.4 C°/F° set
Single combined pr ess on decr ease bott om
temper ature set & Light button to change the
temper ature type ( C°/F°) .
2.3 Sabbath mode
S
M
Press&Hold combined on incr ease bott om
temper ature set & Light buttons for 5 seconds
to activ ate/ deactiv ate Sabbath mode .
When activ at ed, Bott om & Upper temper ature
displays sho w and blinks “Sb ” & “On” for 5
seconds until the it be deactiv ated . In this stat e:
- Any button command is disabled apart from
the incr ease bott om temper ature set & Light
combination command to deactiv at e the
Sabbath mode .
- All lights ar e turned O - apart from “Sb ” &
“On”- , all sounds ar e mut ed .
- Opening or closing the door will not directly
turning on or o any lights, digital r eadouts,
solenoids, fans, valv es, compr essor , icons, tones,
or alarms.
- All alerts will not be display ed until the
Sabbath Mode is deactiv ated, ex cept by the
High/L ow Temper atur e alerts.
S
M
When C° is set , Bott om & Upper temper atur e
display sho ws and blinks “C°” & “C°” for 5
seconds.
Any alert turns o tempor arily .
S
M
When F° is set , Bott om & Upper temper atur e
display sho ws and blinks “F°” & “F°” fo r 5
seconds.
Any alert turns o tempor arily .
S
M
When deactiv at ed, Bott om & Upper temper a-
ture displays sho w and blinks “Sb” & “OF” for 5
seconds.
Ex ception:
The High/L ow Temper atur e alerts will be
display ed in case of high or lo w temper atur e
inside the appliance . The alert icon turns On, but
will not blink, and it will remain until the Sabbath
Mode is deactiv at ed. An audio alarm will
sounds and aut omatically turn o after 10
minutes.
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
When F° is set, Bottom & Upper tempera-
ture display shows and blinks “F°” & “F°” for
5 seconds.
Any alert turns o󰀨 temporarily.
Reset Filter alert
Press & Hold combined on Mode & de-
crease bottons for 5 seconds to reset the
lter change counter.
2.5 Re set Filter alert
Press&Hold combined on On/ O & decr ease
bottoms fo r 5 seconds t o re set the filter change
count er.
If the alert is on, it turns o . If the mode set is Single, the Single zone fe ed -
back will lit-up.
In Single zone mode, both temper ature contr ols
will work in sync.
Relat ed to 3. 5
S
M
If the mode set is Multi, the Multi zone feedback
will lit-up .
In Multi zone mode, each temper ature contr ol
will work separ at ely.
Relat ed to 3. 6
If the mode set is Cellaring , the Single and Multi
zone fe edback will be O, and Bott om & Upper
temper atur e display sho ws “CE” & “CE” until the
Cellaring mode is deactiv at ed .
In Cellaring mode, the temper atur e is fix ed and
can not be changed - ar ound 12° to 16° (TBC) .
S
M
WIP
2.6 Rest to f actory settings
Press&Hold combined on On/ O & increase
upper buttons for 5 seconds to re set the ma-
chine settings to the fact ory setting.
2.7 Single /Multi /C ellaring z one set
Single combined pr ess on incr ease & decr ease
bottom temper ature set to change the Single
zone, Multi zone , and Cellaring mode .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
S
M
If the alert is on, it turns o󰀨.
Single/Muliti/Cellaring zone set
Single press Mode to change the Single
zone, Multi zone, and Cellaring mode.
2.5 Re set Filter alert
Press&Hold combined on On/ O & decr ease
bottoms for 5 seconds t o re set the filter change
count er.
If the alert is on, it turns o . If the mode set is Single, the Single zone fe ed -
back will lit-up.
In Single zone mode, both temper ature contr ols
will work in sync.
Relat ed to 3. 5
S
M
If the mode set is Multi, the Multi zone fe edback
will lit-up.
In Multi zone mode, each temper ature contr ol
will work separ at ely.
Relat ed to 3. 6
If the mode set is Cellaring , the Single and Multi
zone fe edback will be O, and Bott om & Upper
temper atur e display sho ws “CE” & “CE” until the
Cellaring mode is deactiv ated .
In Cellaring mode, the temper ature is fix ed and
can not be changed - ar ound 12° to 16° (TBC) .
S
M
WIP
2.6 Rest to f actory settings
Press&Hold combined on On/ O & increase
upper buttons for 5 seconds to re set the ma-
chine settings to the fact ory setting.
2.7 Single /Multi /C ellaring z one set
Single combined pr ess on incr ease & decr ease
bottom temper atur e set to change the Single
zone, Multi zone , and Cellaring mode .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
S
M
If the mode set is Single, the Single zone
feedback will light-up, and blink and both
temperatures change to 18°C. After 5
seconds without any interaction wih the
Mode button, the Single zone feedback
stops blinking and keeps steady, and both
temperatures show the current temperature.
In Single zone mode, both temperature
controls will work in sync.
2.5 Re set Filter alert
Press&Hold combined on On/ O & decr ease
bottoms for 5 seconds t o re set the filter change
count er.
If the alert is on, it turns o . If the mode set is Single, the Single zone fe ed -
back will lit-up.
In Single zone mode, both temper ature contr ols
will work in sync.
Relat ed to 3. 5
S
M
If the mode set is Multi, the Multi zone fe edback
will lit-up.
In Multi zone mode, each temper ature contr ol
will work separ at ely.
Relat ed to 3. 6
If the mode set is Cellaring , the Single and Multi
zone fe edback will be O, and Bott om & Upper
temper atur e display sho ws “CE” & “CE” until the
Cellaring mode is deactiv ated .
In Cellaring mode, the temper ature is fix ed and
can not be changed - ar ound 12° to 16° (TBC) .
S
M
WIP
2.6 Rest to f actory settings
Press&Hold combined on On/ O & increase
upper buttons for 5 seconds to re set the ma-
chine settings to the fact ory setting.
2.7 Single /Multi /C ellaring z one set
Single combined pr ess on incr ease & decr ease
bottom temper atur e set to change the Single
zone, Multi zone , and Cellaring mode .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
S
M
If the mode set is Multi, the Multi zone
feedback will light-up, and blink and the up-
per temperature changes to 18°C and 8°C
on the bottom. After 5 seconds without any
interaction with the Mode button, the Multi
zone feedback stops blinking and keeps
steady and both temperatures show the
current temperature.
In Multi zone mode, each temperature con-
trol will work separately.
17
User Manual

2.5 Re set Filter alert
Press&Hold combined on On/ O & decr ease
bottoms for 5 seconds t o re set the filter change
count er.
If the alert is on, it turns o . If the mode set is Single, the Single zone fe ed -
back will lit-up.
In Single zone mode, both temper ature contr ols
will work in sync.
Relat ed to 3. 5
S
M
If the mode set is Multi, the Multi zone fe edback
will lit-up.
In Multi zone mode, each temper ature contr ol
will work separ at ely.
Relat ed to 3. 6
If the mode set is Cellaring , the Single and Multi
zone fe edback will be O, and Bott om & Upper
temper atur e display sho ws “CE” & “CE” until the
Cellaring mode is deactiv ated .
In Cellaring mode, the temper ature is fix ed and
can not be changed - ar ound 12° to 16° (TBC) .
S
M
WIP
2.6 Rest to f actory settings
Press&Hold combined on On/ O & increase
upper buttons for 5 seconds to re set the ma-
chine settings to the fact ory setting.
2.7 Single /Multi /C ellaring z one set
Single combined pr ess on incr ease & decr ease
bottom temper atur e set to change the Single
zone, Multi zone , and Cellaring mode .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
S
M
If the mode set is Cellaring, the Single and
Multi zone feedback will be O󰀨, and Bottom
& Upper temperature display shows “CE” &
“CE” blinking. After 5 seconds without any
interaction with the Mode button, the ”CE”
stops blinking and keeps showing ”CE” until
the Cellaring mode is deactivated.
In Cellaring mode, the temperature is xed
and can not be changed - 12°C.
Demo mode
Press & Hold combined on Mode & Lights
buttons for 5 seconds to activate/deactivate
Demo mode.
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper atur e
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper atur e alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door sta ys open fo r some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is r eset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
When activated, the bottom & Upper tem-
perature display shows and blinks ”dE &
”ON” for 5 seconds.
Any alert turns o󰀨 temporarily.
To keep communication that the machine
is in Demo mode, - every 5 minutes the
Bottom & Upper temperature display shows
and blinks ”dE & ”OF” for 5 seconds.
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper atur e
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper atur e alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door sta ys open fo r some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is r eset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
When deactivated, Bottom & Upper tem-
perature display shows and blinks ”dE” &
”OF for 5 seconds.
Any alert turns o󰀨 temporarily.
Mute sounds
Press & Hold combined on decrease bottom
temperature set & Light buttons for 5 sec-
onds to activate/deactivate Mute sounds.
High / Low temperature alert
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper ature
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper ature alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door s ta ys open for some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is reset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
If the Current temperature is 5°C above the
Set temperature for more than 60 minutes,
High Temperature alert shows “Hº” and
blinks the alert icon.
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper ature
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper ature alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door s ta ys open for some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is reset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
If the Current temperature is 2°C below the
Set temperature for more than 60 minutes,
Low Temperature alert shows “Lº” and
blinks the alert icon.
The alerts will not sound in the rst
90 minutes after power on.
18
User Manual

Door open alert
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper ature
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper ature alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door s ta ys open for some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is reset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
When the door stays open for some amount
of time (5 minutes) the icon turns On and
the lights start to dim up and down. If the
door is kept open, after more than 2 min-
utes a sound is played.
Any interaction on the Control panel disa-
bles the blinking and audio signal. The icon
stays on as long the door is open and the
lights go back to normal.
Change lter alert
2.8 Demo mode
Press&Hold combined on On/ O & Lights but-
tons for 5 seconds to activ ate/deactiv ate Demo
mode .
When activ ated, Bottom & Upper temper ature
display sho ws and blinks “ dE” & “On” for 5 sec-
onds.
Any alert turns o  tempor arily.
To keep communication that the machine is in
Demo mode, e very 5 minutes (TBD ), Bottom &
Upper temper atur e display sho ws and blinks
“dE” & “On” for 5 seconds.
S
M
When deactiv ated, Bottom & Upper temper a-
ture display sho ws and blinks “ dE” & “OF” for 5
seconds.
Any alert turns o  tempor arily.
S
M
WIP
3.1 High / Low t emper atur e alert
High Temper ature alert sho ws “Hº” and blinks
the alert icon.
Lo w Temper atur e alert sho ws “ Lº ” and blinks the
alert icon.
S
M
3.2 Door open alert
When the door s ta ys open for some amount o f
time (e.g. 5 minutes - TBD ) the icon turns On. and
a sound is play ed .
Any interaction on the Contr ol panel disable the
audio signal. The icon st ays on as long the door
is open.
S
M
S
M
3.3 Change filter alert
After some amount o f time (TBD ) the icon turns
On.
See 2.5 to kno w ho w to reset the alert . After
re set, the icon turns O  and the count is reset .
S
M
2018.10.0 2
Vintec - Ve stfros t UI Pr oposal
After 6 months the icon turns On.
See "Reset" lter alert, to know how to reset
the alert. After reset, the icon turns O󰀨 and
the count is reset.
19
User Manual

Automatic defrosting
The wine cabinet is defrosted automatically.
Defrost water runs through a pipe and is
collected in a tray above the compressor
where the heat generated by the compres-
sor causes it to evaporate. The defrost
water tray should be cleaned at intervals.
Cleaning
Before cleaning the appliance, unplug it
from the main supply. The cabinet is best
cleaned using warm water (max.65°C) with
a little mild detergent. Never use cleaning
agents that scour. Use a soft cloth. Rinse
with clean water and dry thoroughly. The
defrost water channel, in which condensa-
tion from the evaporator runs, is located
at the bottom of the rear inside wall of the
cabinet and must be kept clean. Add a few
drops of disinfectant, to the defrost water
drain a couple of times a year, and clean
the drain using a pipe cleaner or similar.
Never use sharp or pointed implements.
The sealing strip around the door must be
cleaned regularly to prevent discolouration
and prolong service life. Use clean water.
After cleaning the sealing strip, check that it
continues to provide a tight seal.
Dust collecting on the condenser on the
rear of the cabinet, the compressor and
in the compressor compartment is best
removed using a vacuum cleaner.
Defrosting, cleaning and maintenance
Spare parts
When ordering spare parts, please state
the type, serial and product numbers of
your appliance. This information is given on
the rating plate. The rating plate contains
various technical information, including type
and serial number.
g. 17
20
User Manual