Vintec V110SG e Series User manual

1
Armoire à vin.
Wine Preservation Technology
USER MANUAL
V11 SG”e”-ss
V11 SG”2e”-ss
V155SG”e”-ss
V155SG”2e”-ss

2
WARNING
The information in this document is subject to modification without any prior notice.
VINTEC offers no guarantee for our wine cellar if it is being used for any purpose other
than that for which it was specifically designed. VINTEC cannot be held responsible for any
error in this manual. VINTEC is not responsible or liable for any spoilage or damage to
wines or any other contents incidental or consequential to possible defects of the wine cellar.
Warranty applies to the wine cellar only and not to the contents of the wine cellar.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of e perience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the appliance.
Allow 24 hours before switching on the wine cellar. During this time we recommend
that you leave the door open to clear any residual odors.
BEFORE LOADING & PLUGGING IN THE WINE CELLAR
Important: All models without front venting (air opening) are strictly for free standing
only. ( see technical chart)
Recommendations:
The location you have selected for your wine cellar should:
- be unencumbered and well ventilated;
- be well away from any heat source and direct sunlight;
- not be too damp (laundry, pantry, bathroom etc.);
- have a flat floor,
- have a standard and reliable electricity supply (standard socket to country standards,
linked to the ground), it is NOT recommended to use a multi-socket or e tension lead.
- have a surge protector fitted to the electrical outlet
- away from microwave. Certain microwave ovens do not have wave interference shield.
When placed within 1 meter vicinity of the wine cabinet, they may affect the operation of
the wine cabinet.
The wine cellar should be placed where the ambient temperature is between 5ºC to 43ºC. If
the ambient temperature is above or below this range, the performance of the unit may be
affected. Placing your unit in e treme cold or hot conditions may cause interior
temperatures to fluctuate. The ideal range of temperature may not be reached. (See Climate
Class at the end of this manual)

3
Grounding instructions
The wine cellar must be grounded in case of an electrical short circuit. Grounding reduces
the risk of electrical shock. The wine cellar is equipped with a power cord having a
grounding wire and grounding plug. The wine cellar plug must be plugged into a properly
installed and grounded electrical outlet.
Note : In locations where there is frequent lightning, it is advisable to use surge protectors.
Improper use of the grounding plug can result in the risk of electric shock. Consult a
qualified electrician or service person if the grounding instructions are not completely
understood.
If the supply cord is damaged, it must be replace by a qualified person in order to avoid electrical hazard.
Installing your wine cellar
Unpack and remove all of the protection and adhesive strips from the packaging around and
inside the wine cellar.
The wine cellar must be positioned such that the plug is accessible. Release the power cord.
Move your wine cellar to its final location. The wine cellar should be installed in a suitable
place where the compressor will not be subject to physical contact.
Leveling your wine cellar: Wine cellar must be leveled BE ORE loading your wines.
Your wine cellar is equipped with 4 adjustable feet to facilitate easy leveling. VINTEC
recommends that you tighten the back feet to the ma imum and adjust the front feet to create
a level.

4
Back spacer:
Compressor-run appliances require proper ventilation for proper and longer usage. Your
Vintec wine cellar is supplied with a back spacer. Affi ed the back spacer at the back of the
cellar for air circulation and heat evacuation.
IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE
INSTALLATION FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE
WARRANTY
TURNING ON YOUR WINE CELLAR
Plug in and switch on the cellar by pressing on the power button for a few seconds.
When you use the wine cellar for the first time (or restart the wine cellar after having it
power off for a long time), there will be a few degrees variance between the temperature you
have selected and the one indicated on the LED readout. This is normal and it is due to the
length of the activation time. Once the wine cellar is running for a few hours everything will
stabilize.

5
Important: If the unit is unplugged, power is lost, or turned off, wait 3 to 5 minutes before
restarting the unit. he wine cellar will not start if you attempt to restart before this time
delay.
Operating Noises
To reach the desired temperature settings, VINTEC wine cellars, like all wine cellars
operating with compressors and fans, may produce the following types of noises. These
noises are normal and occur as follows:
- Gurgling sound, caused by the refrigerant flowing through the appliance’s coils,
- Cracking/popping sounds, resulting from the contraction and e pansion of the refrigerant
gas to produce cold,
- Fan operating sound, to circulate the air within the wine cellar.
An individual’s perception of noise is directly linked to the environment in which the wine
cellar is located, as well the specific type of models. VIN EC wine cellars are in line with
international standards for such appliance. VIN EC will always do its utmost to satisfy its
customers but will not retake possession of the goods due to complaints based on normal
operating noise occurrences.
LOADING YOUR WINE CELLAR
You may load your wine bottles in single or double rows while taking note of the following:
if you do not have enough bottles to fill your wine cellar, it is better to distribute the load
throughout the wine cellar so as to avoid “all on top” or “all below” type loads.
- Do remove or relocate adjustable wooden shelves to accommodate larger type of bottles or
increase the capacity of the cellar by stacking the bottles up when necessary. (See
removing shelves)
- Keep small gaps between the wall and the bottles to allow air circulation. Like an
underground cellar air circulation is important to prevent mould and for a better
homogeneous temperature within the cellar.
- Do not over load your wine cellar to facilitate air circulation.
- Do not stack more than 1.5 rows of standard 0.75L bottles per shelves to facilitate air
circulation
- Avoid obstructing the internal fans (located inside on the back panel of the wine cellar).
- Do not try to slide the shelves outwards beyond the fi ed position to prevent the bottles
from falling.

6
- Do not pull out more than one loaded shelf at a time as this may cause the wine cellar to
tilt forward.
- Do not cover the wooden shelves with alloy foil or other materials, as it will obstruct air
circulation.
- Do not move your wine cellar while it is loaded with wines. This might distort the body of
the wine cellar and cause back injury.
TYPES OF REGULATION
Please note that depending on the loading and settings chosen it takes 24hours for the wine
cellar to see the temperature stabilizing.
During this time LED seems to move erratically in particular for 2e models. It is a normal
process. This process occurs whenever the setting is modified and/or whenever a large
amount of bottles are added to the cellar.
Single Temperature Maturing/Storage Wine Cellars:
- “e” series : electronic regulation, digital display
Designed to store and mature all wines: red, white and sparkling. These wine cellars
reproduce the ideal conditions for wine storage, at a constant recommended temperature of
12ºC to 14ºC. They can also be set to provide ideal serving temperature for full enjoyment
of the wine’s qualities. Unless stated by the wine maker on the bottle, VINTEC recommends
7ºC for your champagne, 12ºC for whites and 18ºC for reds. (Refer to “Wine Service
Temperature” recommendation chart)
Two-Temperature Serving Wine Cellars (2-in-1 Wine Cellars):
- “2e” series: electronic regulation digital display
Made of two independent compartments regulated independently as 2 single zone wine
cellars. Like the e models, each compartment are adjustable from 5ºC to 18ºC. Ideal for
storage or “mise en temperature” ( The right temperature for optimum enjoyment)
TEMPERATURE SETTINGS
Important: he LCD displays by default the actual internal air temperature.
The temperature settings are pre-set at the factory as follows. In the event of a power
interruption, all previous temperature settings are automatically erased and it will revert to
the preset temperature settings.

7
Factory preset chart
e models: 12ºC
2e models: 7º℃ for the upper compartment and 12º℃ for the lower compartment.
It is important to understand that there is a difference between the air temperature inside the
wine cellar and the actual temperature of the wine: You will need to wait appro imately 12
hours before noticing the effects of temperature adjustment due to the critical mass within a
full wine cellar.
Once the thermostat is set it is strongly advised not to toy with it or adjust frequently. The
thermostat will maintain the temperature inside the wine cellar within a +/- 2.5ºC range. But
the thermal inertia of the wine and the glass is such that within this temperature range, the
actual temperature of the wine will only fluctuate 0.5ºC to 1ºC.
e models:
The TEMP. SET . LCD displays the set temperature
The DISPLAY LCD displays the internal air temperature
Control panel of e model wine cellars
To modify the pre-set temperature of e models
Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each
depression of the buttons will scroll through the available temperature settings in increments
of 1 degree Celsius. The temperature setting can be adjusted from 5 to 18 .
2e models:
The “DISPLAY LED” displays the internal air temperature. The set temperature
automatically appears by pressing either the UP or DOWN button

8
To modify the pre-set temperature of 2e models
Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each
depression of the buttons will scroll through the available temperature settings in increments
of 1 degree Celsius. The temperature setting can be adjusted from 5 to 18
To visualize the “set” temperature, press and hold the UP or DOWN buttons, the “set”
temperature will temporarily “flash” in the LED display for 5 seconds.
WINE SERVING TEMPERATURE CHART
All wines mature at the same temperature, which is a constant temperature set between 12ºC
to 14ºC. The below chart is an indicative temperature chart to indicate the best temperature
for drinking purposes.
Champagne NV, Sparkling, Spumante 6ºC
Dry White Semillon, Sauvignon Blanc 8ºC
Champagne Vintage, 10ºC
Dry White Chardonnay 10ºC
Dry White Gewürztraminer, Riesling, Pinot grigio 10ºC
Sweet White Sauternes, Montbazillac, Ice Wine, Late Harvest 10ºC
Beaujolais 13ºC
Sweet White Vintage Sauternes 14ºC
White Vintage Chardonnay 14ºC
Red Pinot Noir, 16ºC
Red Grenache, Syrah 16ºC
Red Vintage Pinot Noir 18ºC
Cabernet & Merlot: French, Australian, New Zealand, 20ºC
Chilean, Italian, Spanish, Californian, Argentinean…
Vintage Bordeau … Room temperature not e ceeding 20ºC
IMPORTANT INFORMATION ABOUT TEMPERATURE
Your VINTEC wine cellar has been designed to guarantee optimum conditions for storing
and/or serving your wines.
Fine wines require long and gentle developments and need specific conditions in which to
reach their full potential.

9
All wines mature at the same temperature, which is a constant temperature set between 12ºC
to 14ºC. Only the temperature of “dégustation” (wine appreciation) varies according to the
type of wines (see “Wine Serving Temperature Chart” above). This being said and as it is
for natural cellars used by wine producers for long period of storage, it is not the e act
temperature that is important, but its consistency. In other words, as long as the temperature
of your wine cellar is constant (between 12ºC to 14ºC) your wines will be stored in perfect
conditions.
Not all wines will improve over the years. Some should be consumed at an early stage (2 to 3
years) while others have tremendous ageing capability ( 50 and over). All wines have a peak
in maturity. Do check with your wine merchant to get the relevant information.
DEFROSTING/CONDENSATION/ HYGROMETRY/ VENTILATION
Your wine cellar is designed with “Auto-cycle” defrost system. During “Off-cycle” the
refrigerated surfaces of the wine cellar defrost automatically. Defrost water from the wine
cellar storage compartment drains automatically and part of it goes into a drainage container,
which is located at the back of the wine cellar ne t to the compressor. The heat is transferred
from the compressor and evaporates any condensation that has collected in the pan. Part of
the remaining water is collected within the wine cellar for humidity purposes.
This system enables the creation of the correct humidity level inside your wine cellar
required by the natural cork to maintain a long lasting seal.
Notes: The water collected by condensation, is therefore recycled. Under extremely dry
environmental conditions, you may have to add some water into the water container
provided with your wine cellar.
All units are equipped with a double glazed glass door that has a third internal acrylic layer
to minimize condensation on the glass door.
The wine cellar is not totally sealed; fresh air admission is permitted through the drainpipe.
Air is circulated through the cellar by means of a fan/fans and the hollow shelves.
Notes: During the refrigerating cycle, heat is given off and disperse through the external
surfaces of the wine cellar. Avoid touching the surfaces during those cycles.

10
SLIDING SHELVES
To prevent damaging the door gasket, make sure to have the door opened all the way when
pulling the shelves.
For easy access to the bottles, you must pull the shelves appro imately 1/3 of its depth out of
the rail compartment. These wine cabinets, however, are designed with a notch on each side
of the shelf tracks to prevent bottles from falling.
To remove the shelf :
-align the shelf gap (left and right) under the square plastic block, lift up and tilt the shelf .

11
Drawings for built-in purposes
V110SG ”e”&”2e”
V155SG ”e” & ”2e”

12
OPERATION ANOMALIES
Ensure that there is power to the electrical supply plug by connecting another electrical
appliance to it. Check fuse, if any. Make sure that the door is closed properly.
If your wine cellar appears to be malfunctioning, unplug it and contact your VINTEC’s after
sales service. Any intervention on the cold circuit should be performed by a refrigeration
technician who should carry out an inspection of the circuit sealing system. Similarly, any
intervention on the electrical circuit should be performed by a qualified electrician.
Notes : Any intervention performed by a non-technician will lead to the warranty being
considered as null and void.
POWER FAILURES
In the event of a power interruption, all previous temperature settings are automatically
erased and it will revert to a preset temperature setting . ( see preset chart)
Most power failures are corrected within a short period of time. An hour or two’s loss of
power will not affect your wine cellar’s temperatures. To avoid sudden change of
temperature while the power is off, you should avoid opening the door. For longer period of
power failure, do take steps to protect your wine.
Irrespective of the cause, if you notice either abnormal temperature or humidity levels
inside your wine cellar, be reassured that only long and frequent exposure to these
abnormal conditions can cause a detrimental effect on your wines.

13
TROUBLESHOOTING GUIDE
Common problems may easily be solved, saving you the cost of a possible service call.
Please read carefully the instruction manual and revert to troubleshooting guide chart.
PROBLEM POSSIBLE CAUSE
Wine cellar does not operate. Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a blown fuse.
Wine cellar is not cold enough. Check the temperature control setting.
E ternal environment may require a higher setting.
The door is opened too often.
The door is not closed completely.
The door gasket does not seal properly.
Turns on and off frequently. The room temperature is hotter than normal.
A large amount of contents has been added to the
Wine cellar.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work. Not plugged in.
The circuit breaker tripped or a blown fuse.
The bulb has burned out.
The light button is “OFF”.
Vibrations. Check to assure that the Wine cellar is level.
The Wine cellar seems to make too
much noise.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your Wine
cellar.
Contraction and e pansion of the inside walls may
cause popping and crackling noises.
The Wine cellar is not level.
The door will not close properly. The Wine cellar is not level.
The door was reversed and not properly installed.
The gasket is faulty. ( magnet or rubber is spoiled)
The shelves are out of position.

14
Product specification Chart
Technical data V110SG"e" V110SG"2e" V155SG"e' V155SG"2e"
Capacity750ml 111 Upper 50 151 Upper 70
(Std. Bordeaux type bottle ) Lo er 51 Lo er 71
Net capacity 317 L 308 L 421 L 412 L
Pre-set temp in degrees 12 Upper 7 12 Upper 7
Lo er 12 Lo er 12
Adjustable temp in
degrees 5 -18 Upper 5 -18 5 -18 Upper 5 -18
Lo er 5-18 Lo er 5 -18
Po er Input 180 W 180 W 185 W 185W
Heater Yes Yes Yes Yes
Freestanding or Built-in Both Both Both Both
No.of ooden shelf 11 (10 +base) 10 (9 + base) 15 (14 + base) 14 (13 + base)
Ambient temp in degrees 5-43 5-43 5-43 5-43
Climate Class T T T T
Net dim in mm WXDXH 595X680X1389
595X680x1389 595X680X1762 595X680X1762
Gross dim in mm WXDXH* 650X750X1445 650X750X1445 650X750X1820 650X750X1820
Net eight 86kg 87kg 105kg 106kg
Gross eight 98kg 99kg 118kg 119kg
Standard features:
Compressor operated: R134a
- Available in rated voltage/frequency (as per country's
requirements): 100V/50/60Hz, 220V/50/60Hz,115V/50Hz
- Automatic defrost
- Antifreeze device
- Humidity : 65% RH +/-10% RH
- Adjustable ooden shelves on heels
- Black outer and inner finish
- Internal light LED
- Adjustable feet x 4
- Double glass door ith 3rd acrylic layer
- Glass door opening stainless steel finish on option ref “ss”
*Based on carton box packing dimensions/ eight

15
Copyright: All rights are reserved. All photocopying, reproduction, translation whether partial or total are strictly prohibited,
without prior written consent from VINTEC.
www.vintec-cellar.com