Vintec VWS020SBA-X User manual

User Manual
VWS020SBA-X
VWS020SSA-X
VBS020SBA-X
vintec.com

2
User Manual
3
4
6
7
8
9
10
WARNING
.....................................................
Table of Contents
INSTALLATION
.....................................................
STORAGE
.....................................................
OPERATION
.....................................................
WINE SERVING & DEFROSTING
.....................................................
DOOR REVERSAL
.....................................................
TROUBLESHOOTING & DATA
.....................................................
Important Informaon that may impact your Manufacturer’s Warranty
Adherence to the direcons for use in this manual is extremely important for health and safety. Failure to strictly
adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to
make a claim under the Vintec manufacturer’s warranty provided with your product. Products must be used,
installed and operated in accordance with this manual. You may not be able to claim on the Vintec manufacturer’s
warranty in the event that your product fault is due to failure to adhere to this manual.

WARNING
3
User Manual
Theinforma on in this documentis subjectto
modi!ca"on withoutanypriorno#ce.
Somemodels areavailablein dedicated countriesonly.
VINTEC o$ersnoguaranteeforourWineCellarand
BeverageCentreif it is beingused foranypurposeother
than thatforwhich it wasspeci!callydesigned.
VINTECcannot beheld responsibleforanyerrorin this
manual.
This applianceis not intendedforusebypersons
(includingchildren)with reduced physical,sensoryor
mentalcapabili%es, orlack ofexperienceand knowledge,
unless theyhavebeen given supervision orinstruc&on
concerninguseoftheappliancebya personresponsible
fortheirsafety.
Children should besupervisedtoensuretheydonotplay
with theappliance.
This appliancecan beusedbychildren aged from 8years
and aboveand personswith reducedphysical, sensoryor
mentalcapabili'esorlack ofexperienceand knowledge
if theyhavebeengivensupervisionorinstruc(on
concerninguseoftheappliancein a safewayand
understand thehazardsinvolved.Children shall not play
with theappliance.Cleaningand usermaintenanceshall
not bemadebychildren withoutsupervision .
This applianceuses )ammablerefrigerant,please
securethecoolingpipeduringthedeliveryprocess.
Posi*onthewinecoolerawayfrom directsunlightand
sourcesofheat(stove,heater, radiator, etc.).Never
clean applianceparts with )ammable )uids. Thefumes
can createa !rehazard orexplosion.When disposing
yourappliance, pleasechoosean authorizeddisposalsite.
Children should besupervisedtoensurethattheydo
not playwith theappliance.
R600AWARNINGS
Thefollowingmodels usesmall quan+tyof R600A
(iso-butane) )ammablerefrigerant:
VWS020SBA-X/VWS020SSA-X/VBS020SBA-X:,25g
Foryoursafetypleaseobservethefollowing
recommenda-ons:
-Thisappliancecontainsa small quan.tyof R600A
refrigerantwhich is )ammable.Avoid safetyhazards
bycarefullyinstalling,handling,servicingand disposing
of thisappliance.
-Duringtransporta/on and installa0on,ensurethatthe
tubingoftherefrigerantcircuit is notdamaged.
- Avoid usingormanipula1ngsharp objectsnearthe
appliances.
- Leakingrefrigerantcan igniteand maydamagetheeyes.
- In theeventanydamagedoesoccur,avoid exposureto
open !resand anydevicewhich createsa spark.
Disconnecttheappliancefrom themainspower.
,WARNING:Donotuseelectricalappliancesinsidethe
compartments.
,WARNING:Donotstoreexplosivesubstancessuch as
aerosol canswith a )ammablepropellantinthis
appliance.
,WARNING:Thisapplianceis intended to beused in
household and similarapplica2onssuch as:
- Sta$kitchen areasin shops, o3cesand otherworking
environments;
- Farm housesand byclientsinhotels,motels and other
residen4altypeenvironments;
- Bed and breakfasttypeenvironments;
- Cateringand similarnon-retail applica5ons
,WARNING:Donotuseelectricalappliancesinsidethe
food storagecompartments of theappliance,unless
theyare thetyperecommended bythemanufacturer.
,WARNING:Ifthepowercord is damaged, it must be
replaced bythemanufacturer,itsserviceagentor
similarlyquali!ed personsinorderto avoida hazard.
,WARNING:When posi6oningtheapplianceensurethe
supplycordisnottrapped ordamaged.
WARNING:Donotlocatemul7pleportablesocket-
outletsorportablepowersuppliesattherearofthe
appliance.
,WARNING:Yourapplianceis !8ed with longlifeLED
ligh9ng.In theunlikelyeventtheLED lightsshould fail,
then theLED lights shouldbeserviced bythe
manufacturer,itsserviceagentorsimilarlyquali!ed
personsin orderto avoid a hazard.
,WARNING:Theauthorised person must hold a Gas
WorkAuthorisa:on forhydrocarbonrefrigerants,
beforecarryingoutservicingorrepairswhich involve
theremovalof covers.
Theenvironmentand personalsafetymustbe
considered when disposingofthisappliance.
Pleaseensuretheapplianceis takentoarecyclecentre
forsaferecycling.
This appliancecontainsinsula;on formed with
)ammableblowinggasesand )ammablerefrigerant.
Avoidsafetyhazardsbycarefullydisposingofthis
appliance.
It is hazardousforanyoneotherthan an Authorised
ServicePerson to carryoutservicingorrepairstothis
appliance.
,WARNING:Keep ven<la=onopeningsin theappliance
enclosureorinthebuilt-in structureclearof
obstruc>on.
,WARNING:Donotusemechanicaldevicesorother
meansto acceleratethedefros?ngprocess, otherthan
thoserecommended bythemanufacturer.
,WARNING:Donotdamagetherefrigerantcircuit.
-Thoroughlyven@latetheroomin which theapplianceis
located forseveralminutes.
- NoAfy CustomerServicefornecessaryacBon andadvice.
- Theroomforinstallingtheappliancemust beatleast1
grams;it is alsonoted on theRaCngPlateofthe
appliance.
cubic metreper8gramsofrefrigerant. Therefrigerant
quanDtycontained in this applianceis listed abovein

4
User Manual
Improper use of the grounding plug can result in the risk
of electric shock. Consult a qualified electrician or
service person if the grounding instrucons are not
completely understood. If the supply cord is damaged,
it must be replace by a qualified person in order to avoid
electrical hazard.
INSTALLATION
Unpack and remove all of the protecon and adhesive
strips from the packaging around and inside the Wine
Cellar and Beverage Centre. The Wine Cellar and
Beverage Centre must be posioned such that the plug
socket to country standards, linked to the ground)．It is
NOT recommended to use a mul-socket or extension
lead;
- have a surge protector fied to the electrical outlet;
- away from the microwave oven. Certain microwave
ovens do not have wave interference shield. When
placed within 1 meter vicinity of the wine cabinet, they
may affect the operaon of the wine cabinet.
Notes:
- VWS020SBA-X/VWS020SSA-X/VBS020SBA-X : models
are built-in type as per the drawings in the installaon
secon (page 5).
The Wine Cellar and Beverage Centre should be placed
where the ambient temperature is between 5℃ to 35℃.
If the ambient temperature is above or below this range,
the performance of the unit may be affected. Placing
your unit in extreme cold or hot condions may cause
interior temperatures to fluctuate. The ideal range of
temperature may not be reached. (See Climate Class
at the end of this manual).
Grounding instrucons
The Wine Cellar and Beverage Centre must be grounded
in case of an electrical short circuit. Grounding reduces
the risk of electrical shock. The Wine Cellar and Beverage
Centre is equipped with a power cord having a grounding
wire and plug. The Wine Cellar and Beverage Centre plug
must be plugged into a properly affixed and grounded
electrical outlet.
Note: In locaons where there is frequent lightning, it is
advisable to use surge protectors.
- not be too damp (laundry, pantry, bathroom etc.);
- have a flat floor;
- have a standard and reliable electricity supply (standard
- be unencumbered and well venlated;
- be well away from any heat source and direct sunlight;
Affix the back spacer at the back of the cellar for air
circulaon and heat evacuaon.
IMPORTANT - THIS SPACER MUST BE ATTACHED TO
THE UNIT BEFORE THE INSTALLATION, FOR
VENTILATION PURPOSE.
FAILURE TO DO WILL VOID THE WARRANTY
Compressor run appliances require good venlaon
for effecve and longer usage. Your Vintec Wine Cellar
and Beverage Centre is supplied with a back spacer.
VINTEC recommends that you ghten the back feet to
the maximum and adjust the front feet to level of the
Wine Cellar and Beverage Centre.
Fixing the Back spacer:
Allow 24 hours before switching on the Wine Cellar and
Beverage Centre. During this me we recommend that
you leave the door open to clear any residual odours.
BEFORE LOADING & PLUGGING IN THE Wine Cellar and
Beverage Centre.
Important: All models without front venng (air opening)
are strictly for free standing only. (See technical chart).
Recommendaons:
The locaon you have selected for your Wine Cellar and
Beverage Centre should:
is accessible. Release the power cord.
Move your Wine Cellar and Beverage Centre to its final
locaon. The Wine Cellar and Beverage Centre should
be installed in a suitable place where the compressor
will not be subject to physical contact.
- WARNING: Ensure the plug is accessible when the
appliance is in posion, or a switch is incorporated in
fixed wiring according to the wiring rules.
(See licensed electrician for further advice).
Levelling your Wine Cellar and Beverage Centre: Wine
Cellar and Beverage Centre must be leveled BEFORE
loading your wines. Your Vintec Wine Cellar and
Beverage Centre is equipped with 4 adjustable feet to
facilitate easy leveling.

INSTALLATION
require 10mm clearance on both sides and 30mm on top,
30mm clearance at the rear (Back spacer is provided), to
facilitate installaon, removal, servicing and venlaon.
5
User Manual
Front View (VWS020SBA-X/VWS020SSA-X/
VBS020SBA-X)
DIMENSIONS:
VWS020SBA-X/VWS020SSA-X/VBS020SBA-X
Height 820mm – 870mm (50mm adjustable feet)
Width 295-300 mm
Depth 561mm + 30mm stopper (Total of 591mm)
For VWS020SBA-X/VWS020SSA-X/VBS020SBA-X
a minimum cut out width of 320mm is required to
facilitate installaon, removal and servicing.
1. Vintec “Built in” Wine Cellar and Beverage Centres
are front venng but are not designed to be fully
integrated behind a joinery door.
2. Vintec “Built in” Wine Cellar and Beverage Centres
3. Vintec Built in Wine Cellar and Beverage Centres
draw air from the rear and expels it through the metal
grid under the door at the front. If a kick board is to be
placed in front of the Wine Cellar and Beverage Centre’s
grid another one must be fied into the kick board with
a minimum air flow allowance of 150cm².
4. Vintec “Built in” Wine Cellar and Beverage Centres have
a power switch located on the control panel so power
point locaon is not crical.
5. The Wine Cellar and Beverage Centre requires a
standard 240 volt/10 amp power point. (Or according
to different countries specificaons).
6. The power cord is 1.9m in length and is fixed on the
right side at the back when looking from front of cabinet.
7. As with most appliances of today, the Wine Cellar and
Beverage Centre has sensive electronic components
which are suscepble to damage through lightning and
electricity supply faults. It is therefore advised to use a
power surge protector to avoid problems of this nature.
8. Air vent within the joinery must be provided for Vintec
built in Wine Cellar and Beverage Centres (Front venng)
min width
only 10mm requires for VWS020SSA-X
30mm
Cross secon
Suitable pointe for venlaon grid.
Nite: only one vent is required.
Dimensional drawings:
VWS020SBA-X/VBS020SBA-X
295
30
850
820
10
10
Front View
315
524
30
30
554
Side View
30
554
524
Top View
REVERSIBILITY OF THE DOOR
Warning: To avoid accidents during the process of
changing the door, we recommend that you get
assistance.
The glass door is heavy and may cause injury if dropped.
INSTALLATION DRAWINGS FOR fornt venng under bench
Wine Cellars and Beverage Centres:
In Hot climate zone, an air vent or grid, with a minimum
venlaon size of 200mm x 40mm MUST be cut out at
the rear top of the back paroning or at the top of either
side of the paroning, allowing cool fresh air full access
This air vent or grid must not be opened on the same side as
other appliances such as ovens or an area that is sealed and
without access to fresh cool air. Failing to comply with the
above specificaons could result in WARRANTY void.
to flow into the 30mm gap located at the rear of the
cabinet.

TURNING ON YOUR Wine Cellar and Beverage Centre
Plug in and switch on the cellar by pressing on the
power buon for a few seconds.
When you use the Wine Cellar and Beverage Centre for
the first me (or restart the Wine Cellar and Beverage
Centre aer having it shut off for a long me), there
will be a few degrees variance between the temperature.
5
STORAGE
- Fan operang sound - to circulate the air within
the Wine Cellar and Beverage Centre.
An individual’s percepon of noise is directly linked to
the environment in which the Wine Cellar and
Beverage Centre is located, as well the specific type
of models.
VINTEC Wine Cellar and Beverage Centres are in line
with internaonal standards for such appliances.
VINTEC will always do its utmost to sasfy its
customers but will not retake possession of the goods
due to complaints based on normal operang noise
occurrences.
LOADING YOUR Wine Cellar and Beverage Centre
You may load your wine boles in single or double
rows while taking note of the following: if you do not
have enough boles to fill your Wine Cellar and
Beverage Centre, it is beer to distribute the load
throughout the Wine Cellar and Beverage Centre so
as to avoid all on top or all below type loads.
- Do remove or relocate adjustable wooden shelves to
accommodate larger type of boles or increase the
capacity of the cellar by stacking the boles up when
necessary. (See removing shelves).
- Keep smalls gap between the walls and the boles to
allow air circulaon. Like an underground cellar air
circulaon is important to prevent mould and for a
beer homogeneous temperature within the cellar.
- Do not over load your Wine Cellar and Beverage
Centre to facilitate air circulaon.
- Do not stack more than 1.5 rows of standard
0.75L boles per shelves to facilitate air circulaon.
- Avoid obstrucng the internal fans (Located inside
on the back panel of the Wine Cellar and Beverage
Centre).
- Do not slide the shelves outwards beyond the fixed
posion to prevent the boles from falling.
- Do not pull out more than one loaded shelf at a me
as this may cause the Wine Cellar and Beverage
Centre to lt forward.
- Do not cover the wooden shelves with alloy foil or
other materials, as it will obstruct air circulaon.
- Do not move your Wine Cellar and Beverage Centre
while it is loaded with wines. This might distort the
body of the Wine Cellar and Beverage Centre and
cause back injury.
- Do not cover the wooden shelves with alloy foil or
other materials, as it will obstruct air circulaon.
- Do not move your Wine Cellar and Beverage Centre
while it is loaded with wines. This might distort the
body of the Wine Cellar and Beverage Centre and
cause back injury.
6
User Manual
You have selected and the one indicated on the LED
readout. This is normal and it is due to the length of the
acvaon me. Once the Wine Cellar and Beverage
Centre is running for a few hours everything will
stabilise.
Important: If the unit is unplugged, turned off, or power
is lost due to an electricity power outage wait 3 to 5
minutes before restarng the unit.
The Wine Cellar and Beverage Centre will not start if
you aempt to restart before this me delay.
VWS020SSA-X
weiVpoT
weiVediS
weiVtnorF
OPERATING NOISES
To reach the desired temperature sengs, VINTEC
Wine Cellar and Beverage Centres, like all Wine
Cellar and may produce the following types of
noises. These noises are normal and may occur as
follows:
- Gurgling sound - caused by the refrigerant flowing
through the appliance’s coils.
- Cracking/popping sounds - resulng from the
contracon and expansion of the refrigerant gas to
produce cold.

OPERATION
TYPES OF REGULATION
Please note that depending on the loading and
sengs chosen it takes about 24 hours for the Wine
Cellar and Beverage Centre to see the temperature
stabilising. During this me the LED seems to move
erracally in parcular for dual zone models. It is
normal and this process occurs whenever the seng
is modified and/or whenever a large amount of
boles are added to the cellar. Designed to store and
mature all wines: red, white and sparkling. These
Wine Cellar and Beverage Centres reproduce the
ideal condions for wine storage, at a constant
recommended temperature of 12℃. They can also
be set to provide ideal serving temperature for full
enjoyment of the wine’s qualies. Unless stated by
the wine maker on the bole, VINTEC recommends
7℃ for your champagne, 12℃ for whites and 18℃
for reds. (Refer to Wine Service Temperature
recommendaon chart).
Designed to store wines at the correct temperature
for best enjoyment. The upper chamber can hold 12,
14 or 16 boles, depending on the models, at a
temperature of 6℃ to 10℃ dedicated mainly to
white, sparkling wines and champagnes. The lower
chamber accommodates 20, 30 or 34 boles
depending on the models, mainly for red wines,
which could be stored either at room emperature
(18℃-20℃) for consumpon or at 12℃ for a
longer me of storage.
TEMPERATURE SETTINGS
Important: The LCD displays by default the actual
internal air temperature.
The temperature sengs are pre-set at the factory as
follows. In the event of a power interrupon, all
previous temperature sengs are automacally
erased and it will revert to the preset temperature
sengs.
7
User Manual
Factory preset chart
Model
VWS020SBA-X
VWS020SSA-X
VBS020SBA-X
Seng Temperature
12℃
6℃
12℃(+/-2.5℃)
6℃(+/-2.5 ℃)
Once the temperature is set, it is strongly advised not to
toy with it or adjust frequently. The thermostat will
maintain the temperature inside the Wine Cellar and
Beverage Centre within a +/- 2.5℃ range.
But the thermal inera of the wine and the glass is such
that within this temperature range, the actual
temperature of the wine will only fluctuate 0.5℃ to 1℃.
Control panel of VWS020SBA-X / VWS020SSA-X/
VBS020SBA-X models
To modify the pre-set temperature of single zone
models Adjust the desired cooling temperature by
pressing the UP or DOWN buons. Each depression
of the buons will scroll through the available
temperature sengs in increments or decrease of
1 degree Celsius.
The temperature seng can be adjusted from 6℃ to
18℃(beverage centre : 2℃ to 10℃).
To view the set temperature, press and hold the UP or
DOWN buons, the set temperature will temporarily
flash in the LED display for 5 seconds.
Aer 5 seconds the temperature will return to display
the actual temperature.
Internal light
In order to reduce energy consumpon, this wine
cabinet will automacally switch off the LED lights
aer 10 minutes.
If you want the LED light to remain on connuously,
this is possible. Please press and hold the LIGHT
buon for 5 seconds, the display will show LP. Aer
4 seconds the display will revert back to normal and
the light will remain on unl manually switched off.
If you want to revert back and conserve energy
(recommended), please press and hold the LIGHT
buon for 5 second, the display will show LF,aer
4 seconds the display will revert back to normal, and
the light will automacally switch off aer 10 minutes.
WINE SERVING TEMPERATURE CHART
All wines mature at the same temperature, which is a
constant temperature set between 12℃ to 14℃.
The below chart is an indicave temperature chart to
indicate the best temperature for drinking purposes.
It is important to understand that there is a difference
between the air temperature inside the Wine Cellar
and Beverage Centre and the actual temperature of
the wine: You will need to wait approximately 12 hours
before nocing the effects of temperature adjustment
due to the crical mass within a full Wine Cellar and
Beverage Centre.

Champagne NV, Sparkling, Spumante, 6℃
Dry White Semillon, Sauvignon Blanc, 8℃
Champagne Vintage, 10℃
Dry White Chardonnay, 10℃
Dry White Gewürztraminer, Riesling, Pinot grigio, 10℃
Sweet White Sauternes, Barsac, Montbazillac, Ice
Wine, Late Harvest , 10℃
Beaujolais, 13℃
Sweet White Vintage: Sauternes, 14℃
White Vintage Chardonnay , 14℃
Red Pinot Noir, 16℃
Red Grenache, Syrah , 16℃
Red Vintage Pinot Noir, 18℃
Cabernet & Merlot: French, Australian, New Zealand,
18℃
Chilean, Italian, Spanish, Californian, Argennean,
Vintage Bordeaux . 18℃
WINE SERVING & DEFROSTING
IMPORTANT INFORMATION ABOUT TEMPERATURE
Your VINTEC Wine Cellar and Beverage Centre has
been designed to guarantee opmum condions for
storing and/or serving your wines.
Fine wines require long and gentle developments and
need specific condions in which to reach their full
potenal.
All wines mature at the same temperature, which is a
constant temperature set between 12℃ to 14℃. Only
the temperature of dégustaon (wine appreciaon)
varies according to the type of wines (see Wine Serving
Temperature Chart above). This being said and as it is
for natural cellars used by wine producers for long periods
of storage, it is not the exact temperature that is
important, but its consistency. In other words, as long as
the temperature of your Wine Cellar and Beverage
Centre is constant (between 12℃ to 14℃) your wines will
be stored in perfect condions.
Not all wines will improve over the years. Some should be
consumed at an early stage (2 to 3 years) while others
have tremendous ageing capability (50 and over).
All wines have a peak in maturity. Do check with your
wine merchant to get the relevant informaon
DEFROSTING/CONDENSATION/ HYGROMETRY/
VENTILATION
Your Wine Cellar and Beverage Centre is designed with
Auto-cycle defrost system. During Off-cycle the
refrigerated surfaces of the Wine Cellar and Beverage
Centre defrost automacally. Defrost water from the
Wine Cellar and Beverage Centre storage compartment
All units are equipped with a double glazed glass door
that has a third internal acrylic layer to minimise
condensaon on the glass door.
The Wine Cellar and Beverage Centre is not totally
sealed; Some fresh air is allowed through the
drainpipe.
Air is circulated through the cellar by means of a
fan/fans and the hollow shelves.
Notes: During the refrigerang cycle, heat is given off
which disperses through the external surfaces of the
Wine Cellar and Beverage Centre. Avoid touching
the surfaces during those cycles.
ADJUSTABLE WOODEN SHELVES:
ADJUSTING/REMOVING THE SHELVES
For easy access to the storage content, you must pull
the shelves approximately 1/3 of its depth out of the rail
8
User Manual
drains automacally and part of it goes into a drainage
container, which is located at the back of the Wine
Cellar and Beverage Centre next to the compressor.
The heat is transferred from the compressor
and evaporates any on that has collected in the pan.
Part of the remaining water is collected within the
Wine Cellar and Beverage Centre for humidity purposes.
This system enables the creaon of the correct humidity
level inside your Wine Cellar and Beverage Centre
required by the natural cork to maintain a long lasng
seal.
compartment. These wine cabinets, however, are
designed with a notch on each side of the shelf tracks
to prevent boles from falling.
When removing any of these shelves out of the rail
compartment, lt the shelf as per the diagram and
simply pull out, or push in the shelf unl it sits on the
support brackets securely.
- To prevent damaging the door gasket, make sure to
have the door all the way opened when pulling shelves
out of the rail compartment.
- When removing any of these shelves out of the rail
compartment: to fit or remove the shelf, lt the shelf
as per the diagram and simply pull out, or push in the
shelf unl it sits on the support brackets securely.
Improper use of the grounding plug can result in the risk
of electric shock. Consult a qualified electrician or
service person if the grounding instrucons are not
completely understood. If the supply cord is damaged,
it must be replace by a qualified person in order to avoid
electrical hazard.
INSTALLATION
Unpack and remove all of the protecon and adhesive
strips from the packaging around and inside the Wine
Cellar and Beverage Centre. The Wine Cellar and
Beverage Centre must be posioned such that the plug

DOOR REVERSAL
OPERATION ANOMALIES
Ensure that there is power to the electrical supply
plug by connecng another electrical appliance to it.
Check fuse, if any.
Make sure that the door is closed properly.
If your Wine Cellar and Beverage Centre appears to
be malfunconing, unplug it and contact your
VINTEC’s aer sales service. Any intervenon on the
cold circuit should be performed by a refrigeraon
technician who should carry out an inspecon of the
circuit sealing system. Similarly, any intervenon on
the electrical circuit shouldbe performed by a
qualified electrician.
9
User Manual
REVERSIBILITY OF THE DOOR
Warning: To avoid accidents during the process of
changing the door, we recommend that you get
assistance.
The glass door is heavy and may cause injury if dropped.
VWS020SBA-X/VBS020SBA-X
1. Open the door to a 90 degrees angle, take out the 2
screws from lower door axis, remove the door ,
Remove the axis plate from the door. Unscrew the
screw located underneath the doorframe and the
limit device , and relocate it at le end side of the
door frame.
2. Take out the 3 hinge screws from the lower hinge
(right) and remove it.
3. Take out the 3 hinge screws from the top hinge
(right) and remove it.
4. Remove decorave nail from le top of cabinet
and install spare top hinge (Le) at le top of
cabinet with 3 screws.
5. Following the above procedure, install the spare
lower hinge to the le.
6. Install and aligned the door.
7. Insert the plasc caps to cover the holes.
VWS020SSA-X
1. Open the door to a 90 degrees angle, take out the 2
screws from lower door axis, remove the door ,
Remove the axis plate from the door. Unscrew the
screw located underneath the doorframe and the
limit device , and relocate it at le end side of the
door frame.
2. Take out the 3 hinge screws from the lower hinge
(right) and remove it.
3. Take out the 3 hinge screws from the top hinge
(right) and remove it.
4. Remove decorave nail from le top of cabinet
and install spare top hinge (Le) at le top of
cabinet with 3 screws.
5. Following the above procedure, install the spare
lower hinge to the le.
6. Rotate door at 180 degrees, then assemble the
door as per the reverse way of removal.
7. Insert the plasc caps to cover the holes.

POWER FAILURES
In the event of a power interrupon, all previous
temperature sengs are automacally erased and it
will revert to a preset temperature seng. (See preset
chart). Most power failures are corrected within a short
period of me. An hour or two’s loss of power will not
affect Wine Cellar and Beverage Centre’s temperatures.
To avoid sudden change of temperature while the
power is off, you should avoid opening the door.
For longer periods of power failure, do take steps
to protect your wine.
Irrespecve of the cause, if you noce either abnormal
temperature or humidity levels inside your Wine Cellar
and Beverage Centre, be reassured that only long and
frequent exposure to these abnormal condions can
cause a detrimental effect on your wines.
TROUBLESHOOTING GUIDE
Common problems may easily be solved,
saving you the cost of a possible service call.
Please read carefully the instrucon manual
and refer to the troubleshoong guide chart.
PROBLEM POSSIBLE CAUSE
Wine Cellar and Beverage
Centre does not operate.
Wine Cellar and Beverage
Centre is not cold enough.
Turns on and off frequently.
The light does not work.
The Wine Cellar and Beverage
Centre seems to make too
much noise.
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or the fuse is
broken.
Check the temperature control seng.
External environment may require a
higher seng.
The door is opened too oen.
The door is not closed completely.
The door gasket does not seal properly.
The room temperature is higher than
normal.
A large amount of contents has been
added to the Wine Cellar and Beverage
Centre.
The door is opened too oen.
The door is not closed completely.
The temperature control is not set
correctly.
The door gasket does not seal properly.
Not plugged in.
The circuit breaker tripped or a blown
fuse.
The bulb is out of order.
The light buon is “OFF”.
Check to assure that the Wine Cellar and
Beverage Centre is level.
A Gurgling noise may come from the low
side of the refrigerant system, which is
normal as each cycle ends in your Wine
Cellar and Beverage Centre.
Contracon and expansion of the inside
walls may cause popping and crackling
noises.
The Wine Cellar and Beverage Centre is
not level.
Vibraons.
TROUBLESHOOTING & DATA
10
User Manual
Notes : Any intervenon performed by a non- authorised
technician by Vintec will lead to the warranty being
considered as null and void.
1. Models with a heater will raise their temperature to the set
temperature if the ambient temperature is below the set
temperature. Models without a heater will not raise the
temperature to the set temperature in these condions.
Technical Data:
VWS020SBA-X
Models
Preset Temperature (°C)
degrees
Heater
( 1)
19
25g
56L
-
-
56L
Net weight
Gross weig
Number of shelves:
Ambient temperature
range (°C)
Dimensions (mm) (WxDxH)
ht
28kg
3
6(5+base)
5-35°C 5-35°C
Packaged Dimensions
(mm) (WxDxH)
295x561x820
340x630x860
31kg
Capacity
(1)
VBS020SBA-X
6°C
2-10°C
-
295x561x820
340x630x860
28kg
31kg
53
-
Freestanding or Built-in Built-in Built-in
VWS020SSA-X
6-18°C
12°C
25g
Adjustable tmep in
Net capacity
Gas charge(g)
750ml bordeaux Boles
375ml Beer Boles
The door will not close properly.
The Wine Cellar and Beverage Centre is
not level.
The door was reversed and not properly
installed.
The gasket is faulty. (Magnet or rubber
is spoiled).
The shelves are out of posion.
RoHS
Compliant
Comformed to the spulaon on permissible content limitaon of
some hazardous & restricted chemical subsances.
(RoHS compliant)
(According to the Circular No. 30/2011/TT-BCT. Vietnam, dated 10th August, 2011)

vintec.com
Vintec. We are part of the
Electrolux Family. To add
a touch of professional
inspiraon to your home.
Stay in touch and share your
user experience by following us:
@vintecclub
Service and support
In the rare event that your Vintec cabinet does not perform
to your sasfacon, contact our dedicated support team.