VIPA HMI 62E-MDC0 User manual

VIPA HMI
Touch Panel | 62E-MDC0 | Manual
HB160E_TP-ECO | RE_62E-MDC0 | Rev. 12/30
July 2012

Copyright © VIPA GmbH. All Rights Reserved.
This document contains proprietary information of VIPA and is not to be disclosed or used except in accordance with applicable
agreements.
This material is protected by the copyright laws. It may not be reproduced, distributed, or altered in any fashion by any entity (either
internal or external to VIPA), except in accordance with applicable agreements, contracts or licensing, without the express written
consent of VIPA and the business management owner of the material.
For permission to reproduce or distribute, please contact:
VIPA, Gesellschaft für Visualisierung und Prozessautomatisierung mbH
Ohmstraße 4, D-91074 Herzogenaurach, Germany
Tel.: [phone]
Fax.: [phone]
EMail: inf[email protected]
http://www.vipa.com
Note
Every effort has been made to ensure that the information contained in this document was complete and accurate at the time of
publishing. Nevertheless, the authors retain the right to modify the information. This customer document describes all the hardware
units and functions known at the present time. Descriptions may be included for units which are not present at the customer site. The
exact scope of delivery is described in the respective purchase contract.
CE Conformity
Hereby, VIPA GmbH declares that the products and systems are in compliance with the essential requirements and other relevant
provisions of the following directives:
• 2004/108/EC Electromagnetic Compatibility Directive
• 2006/95/EC Low Voltage Directive
Conformity is indicated by the CE marking affixed to the product.
Conformity Information
For more information regarding CE marking and Declaration of Conformity (DoC), please contact your local VIPA customer service
organization.
Trademarks
VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V, System 500S and Commander Compact are
registered trademarks of VIPA Gesellschaft für Visualisierung und Prozessautomatisierung mbH.
SPEED7 is a registered trademark of profichip GmbH.
SIMATIC, STEP,SINEC, S7-300 and S7-400 are registered trademarksof Siemens AG.
Microsoft und Windows are registered trademarks of Microsoft Inc., USA.
Portable Document Format (PDF) and Postscript are registered trademarks of Adobe Systems, Inc.
All other trademarks, logos and service or product marks specified herein are owned by their respective companies.
Information product support
Contact your local VIPA Customer Service Organization representative if you wish to report errors or questions regarding the contents
of this document. If you are unable to locate a customer service center, contact VIPA as follows:
VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Telefax:[phone]
EMail: documentati[email protected]
Technical support
Contact your local VIPA Customer Service Organization representative if you encounter problems with the product or have questions
regarding the product. If you are unable to locate a customer service center, contact VIPA as follows:
VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Telephone: [phone] (Hotline)
EMail: s[email protected]

Manual VIPA HMI Contents
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 i
Contents
About this manual....................................................................................1
Safety information....................................................................................3
Chapter 1 Hardware description .....................................................1-1
Safety information for Users.................................................................1-2
Properties.............................................................................................1-3
Structure ..............................................................................................1-4
Components.........................................................................................1-6
Dimensions ..........................................................................................1-9
Technical Data...................................................................................1-10
Chapter 2 Deployment Touch Panel ...............................................2-1
Installation............................................................................................2-2
Installation of the optional MPI/PROFIBUS DP interface......................2-4
Commissioning.....................................................................................2-6
Connection to a PLC system..............................................................2-11
Operating system Windows®Embedded CE 6.0 Core .......................2-12
Integrated Server ...............................................................................2-18
Access to the network resources........................................................2-22
Chapter 3 Installation Guidelines....................................................3-1
Basic rules for the EMC-equitable assembly of installations.................3-2
EMC-equitable assembly......................................................................3-6
EMC-equitable cabling .........................................................................3-7
Special precautions providing high noise immunity ............................3-11
Checklist for the EMC-compliant installation of controllers.................3-12

Contents Manual VIPA HMI
ii HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30

Manual VIPA HMI About this manual
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1
About this Manual
The manual describes the Touch Panel TP 604LC from VIPA. Here you
find detailed descriptions of the Touch Panel beside a product overview.
You get information about structure, project engineering and operation of
the Touch panels from VIPA.
Chapter 1: Hardware description
During this chapter you get hints for deployment of the Touch Panel
TP 604LC from VIPA.
Besides of a description of the single components of the Touch Panel, you
will also find the dimensions that are required for the installation. The
chapter closes with the technical data.
Chapter 2: Deployment Touch Panel
This chapter deals with the application of the Touch Panel.
At the beginning of the chapter you get information about the assembly and
the connection of the Touch Panel. The main part of the chapter introduces
Windows®CE and the various communication options offered by the Touch
Panel.
Chapter 3: Installation guidelines
The chapter "Installation Guidelines" gives you information about the
interference-free installation of Programmable Logic Controls (PLC)
together with a Touch Panel.
Here we describe possible paths how interference can enter the controller,
how you ensure the electromagnetic compatibility (EMC) and how to
approach shielding and screening issues.
Overview

About this manual Manual VIPA HMI
2 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
This manual describes the Touch Panel TP 604LC from VIPA. The manual
consists of chapters. Every chapter provides the description of one specific
topic.
It describes the installation, project engineering, usage and the technical
data.
This manual is part of the documentation package
with order number VIPA HB160E_TP-ECO and relevant for:
Product Order number as of state:
HW OS
TP 604LC VIPA 62E-MDC0 01 Windows®CE 6.0 Core
This manual provides the following guides:
• An overall table of contents at the beginning of the manual
• An overview of the topics for every chapter
The manual is available in:
• printed form, on paper
• in electronic form as PDF-file (Adobe Acrobat Reader)
[Button] Buttons are put in brackets e.g. [NEXT] or [OK].
[Key] Key entry are put in brackets e.g. [STRG]+[A].
Display
output Display outputs are illustrated as Courier e.g.
\flashdisk>
Keyboard
entry Keyboard entries are illustrated as Courier bold e.g.
\flashdisk> Dir
Terms Menus, Display elements, terms are italics.
Important passages in the text are highlighted by following icons and
headings:
Danger!
Immediate or likely danger.
Personal injury is possible.
Attention!
Damages to property is likely if these warnings are not heeded.
Note!
Supplementary information and useful tips.
Objective and
contents
Guide to the
document
Availability
Description
conventions
Icons
Headings

Manual VIPA HMI Safety information
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 3
Safety information
The Touch Panels are constructed and manufactured for:
• VIPA CPUs 11x, 21x, 31x, 51x and S7-300/400 from Siemens
• communication and process control
• general control and automation applications
• industrial applications
• operation within the environmental conditions specified in the technical
data
• installation into a cubicle
Danger!
This device is not certified for applications in
• in explosive environments (EX-zone)
The manual must be available to all personnel in the
• project design department
• installation department
• commissioning
• operation
The following conditions must be met before using or commissioning
the components described in this manual:
• Modification to the process control system should only be carried out
when the system has been disconnected from power!
• Installation and modifications only by properly trained personnel
• The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Applications
conforming with
specifications
Documentation
Disposal

Safety information Manual VIPA HMI
4 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-1
Chapter 1 Hardware description
During this chapter you get hints for deployment of the Touch Panel
TP 604LC from VIPA.
Besides of a description of the single components of the Touch Panel, you
will also find the dimensions that are required for the installation. The
chapter closes with the technical data.
Topic Page
Chapter 1 Hardware description......................................................1-1
Safety information for Users.................................................................1-2
Properties.............................................................................................1-3
Structure ..............................................................................................1-4
Components.........................................................................................1-6
Dimensions ..........................................................................................1-9
Technical Data...................................................................................1-10
Overview
Content

Chapter 1 Hardware description Manual VIPA HMI
1-2 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
Safety information for Users
VIPA modules make use of highly integrated components in MOS-
technology. These components are extremely sensitive to over-voltages
that can occur during electrostatic discharges.
The following symbol is attached to modules that can be destroyed by
electrostatic discharges:
The symbol is located on the module, the module rack or on packing
material and it indicates the presence of electrostatic sensitive equipment.
It is possible that electrostatic sensitive equipment is destroyed by energies
and voltages that are far less than the human threshold of perception.
These voltages can occur where persons do not discharge themselves
before handling electrostatic sensitive modules and they can damage
components thereby, causing the module to become inoperable or
unusable. Modules that have been damaged by electrostatic discharges
may fail after a temperature change, mechanical shock or changes in the
electrical load.
Only the consequent implementation of protection devices and meticulous
attention to the applicable rules and regulations for handling the respective
equipment can prevent failures of electrostatic sensitive modules.
Modules have to be shipped in the original packing material.
When you are conducting measurements on electrostatic sensitive modules
you should take the following precautions:
• Floating instruments must be discharged before use.
• Instruments must be grounded.
Modifying electrostatic sensitive modules you should only use soldering
irons with grounded tips.
Attention!
Personnel and instruments should be grounded when working on
electrostatic sensitive modules.
Handling of
electrostatic
sensitive modules
Shipping of
electrostatic
sensitive modules
Measurements
and alterations on
electrostatic
sensitive modules

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-3
Properties
The Touch Panel allows you to visualize and alter operating states and
recent process values of a connected PLC.
The VIPA Touch Panel is a compact and modular embedded PC based on
Windows®CE. Besides of the extensive Windows®CE functions the Touch
Panel offers varied communication possibilities. Here the Touch Panel can
simply be configured, controlled and remoted. By including a selectable
HMI/SCADA runtime the Touch Panel is particularly suitable for monitoring
and controlling of process cycles.
• Windows®CE 6.0 Core
• Movicon Basic
• Processor ARM11, 533MHz
• Flash memory 128Mbyte, RAM 128Mbyte
• MMC/SD card slot
• RS232, RS232/RS422/RS485, USB-A and Ethernet interface
• MPI/PROFIBUS DP interface (optional)
• robust plastic case
• display resolution 272 x 480 / 480 x 272
• battery backed clock
• resistive analog touch screen
• easy mounting via 4 mounting clips
• protection class IP65 (frontal)
Type Order number Description
TP 604LC VIPA 62E-MDC0 4.3" TFT color, RS232, RS232/RS422/RS485, USB-A,
Ethernet RJ45
MPI/PROFIBUS
DP interface VIPA 961-0MP0 MPI/PROFIBUS DP interface (optional)
General
TP 604LC
62E-MDC0
Order data

Chapter 1 Hardware description Manual VIPA HMI
1-4 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
Structure
[1] MPI/PROFIBUS DP interface
COM 3 (optional)
[2] RS232 interface COM 1
[3] RS232/RS422/RS485
interface COM 2
Touch Panel
4
2
3
1
[4] Display with touch sensitive
area (touch screen)
[1] MPI/PROFIBUS DP interface
COM 3 (optional)
[2] RS232 interface COM 1
2
1
[1] RS232/RS422/RS485
interface COM 2
1
Front view
Side view
Bottom view

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-5
2
3
4
1
COM3
COM1
COM2
LAN
+ -
SD
[1] Slot for SD/MMC storage medium
[2] RJ45 jack for Ethernet communication
[3] "Host"-USB-A interface
[4] Slot for DC 24V voltage supply
Note!
Please regard that the Touch Panel always has to be supplied with external
voltage!
Back view

Chapter 1 Hardware description Manual VIPA HMI
1-6 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
Components
The following memory systems are available for every Touch Panel:
• 128Mbyte work memory
• 128Mbyte Flash disk (50Mbyte for user data)
• USB storage media using "Host"-USB-A interface
• Slot for SD/MMC
Every Touch Panel has a work memory with a size of 128Mbyte. The work
memory is not buffered and is deleted after shut down. Please regard that
also registry entries are stored in the work memory that are set back to
default settings after the next re-boot.
As internal permanent storage medium every Touch Panel has a flash disk
with a size of 128Mbyte (50Mbyte user data). After the start of Windows®
CE this memory is listed as Flashdisk at My Device.
The connection of USB sticks and USB drives by use of the "Host"-USB-A
interface is supported by the Touch Panel. After connection the storage
media is listed as Hard Disk at My Device.
At the back of the Touch Panel there are the card slots for memory cards.
At this slot you may plug storage modules of the type SD/MMC. The card
may be plugged and removed during runtime and is immediately listed as
SDMMC Card at My Device.
• Interface is compatible to the COM interface of a PC
• Logical signals as voltage levels
• Point-to-point links with serial full-duplex transfer in two-wire technology
up to 15m distance
• Data transfer rate up to 115.2kBaud
Connection RS232 9pin plug Connection RS232
Pin RS232
1 CD
2 RxD
3 TxD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
1
2
3
4
5
6
7
8
9
9 RI
RxD
TxD
GND
TxD
RxD
3
2
GND 5
RTS
CTS
7
8
shield
RS232 Periphery
shield
Memory
management
Work memory
Flash disk
USB storage media
Slot for SD/MMC
RS232 interface

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-7
Connection 25pin jack Connection RS 232
Pin Signal Type
1 Shield -
2 TxD RS232C
3 RxD RS232C
4 RTS RS232C
5 CTS RS232C
6 DSR RS232C
7 GND 5V-/RS232C
RxD
TxD
GND
TxD
RxD
2
3
GND 7
DCD
RI
shield
RS232 Periphery
shield
4
5
RTS
CTS
6
DSR
20
DTR
8
22
CTS
RTS
DSR
DTR
DCD
RI
8 CD RS232C Connection RS422
9 n.c. -
10 n.c. -
11 n.c. -
12 TxD(A) RS422/RS485
13 TxD(B) RS422/RS485
14 RTS(A) RS422
15 RTS(B) RS422
16 n.c. -
TxD+ (A)
TxD- (B)
RxD+ (A)
RxD- (B)
Shield
RS422 Periphery
12
13
24
25
M5V
TxD+
TxD-
RxD+
RxD-
P5V
7
21
1
17 n.c. - Connection RS485
18 CTS(A) RS422
19 CTS(B) RS422
20 DTR RS232C
21 5V+ -
22 RI RS232C
23 n.c. -
24 RxD(A) RS422
14
2
3
4
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
1
25 RxD(B) RS422
TxD+ (A)
TxD- (B)
RxD+ (A)
RxD- (B)
Shield
RS485 Periphery
12
13
24
25
M5V
RxD+
RxD-
P5V
7
21
1
Connection RS485 9pin jack Connection RS485
Pin RS485
1 n.c.
2 M24V
3 RxD/TxD-P (Line B)
4 RTS
5 M5V
6 P5V
7 P24V
8 RxD/TxD-N (Line A)
5
4
3
2
1
9
8
7
6
9 n.c.
RxD/TxD-P(B)
Shield
RS485
3
8
P24V
RxD/TxD-P(B)
5
RxD/TxD-P(B)
RxD/TxD-N(A)
Periphery
P5V
M5V
RTS 4
6
7
Shield
RS232/RS422/RS485
interface
MPI/PROFIBUS DP
interface (optional)

Chapter 1 Hardware description Manual VIPA HMI
1-8 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
An RJ45 jack provides the interface to the twisted pair cable, required for
Ethernet. The pin assignment of this jack is as follows:
8pin RJ45 jack
Pin Signal
1 Transmit +
2 Transmit -
3 Receive +
4 -
5 -
6 Receive -
7 -
8 -
Using the "Host"-USB-A interface mouse, keyboard, USB stick or USB hard
discs can be connected.
The pin assignment is as follows:
"Host"-USB-A:
Pin Assignment
1 VCC
2 DM
3 DP
1
2
3
4
4 GND
The Touch Panel has got an integrated power supply.
DC 24V
The power supply has to be provided with DC 24V (20.4 ... 28.8V). For this
you find an according DC 24V slot at the back.
The power supply is protected against inverse polarity and overcurrent.
Ethernet
connection
1
2
3
4
5
6
7
8
"Host"-USB-
A
Power suppl
y

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-9
Dimensions
installation width
installation hight
installation de
p
th
width
hight
For the installation of the Touch Panel in control cabinets and desks the
following dimensions are necessary:
Front panel width 2.5 ... 6mm
Installation cutting (W x H) 123 x 99mm
Front panel (W x H) 140 x 116mm
Rear panel (W x H x D) 122 x 98 x 51mm
Installation depth 51mm
Note!
The degrees of protection are only guaranteed when the following is
observed:
• Material thickness at the mounting cut-out: 2.5 ... 6mm
• The deviation from the plane for the panel cut-out is ≤0.5mm. This
condition must be fulfilled for the mounted HMI device
• Permissible surface roughness in the area of the seal: ≤120µm
(friction coefficient 120)
Installation
dimensions
4.3''
62E-MDC0

Chapter 1 Hardware description Manual VIPA HMI
1-10 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30
Technical Data
Order number 62E-MDC0
Type Touch Panel TP 604LC
Display
Display size (diagonal) 4.3 "
Display size (width) 95 mm
Display size (height) 54 mm
Resolution 272 x 480 / 480 x 272
Type of display TFT color (64K colors)
MTBF Backlights (25°C) 30000 h
System properties
Processor ARM11 533 MHz
Operating system Windows CE 6.0
Work memory 128 MB
User memory 128 MB
Avilable memory (user data) 50 MB
SD/MMC Slot 9
CF Card Slot Typ II -
Time
Real-time clock buffered 9
Clock buffered period (min.) 26 W
Accuracy (max. deviation per day) 2 s
Operating controls
Touchscreen resistive
Keyboard external via USB
Mouse external via USB
Interfaces
MPI, PROFIBUS-DP optional
MPI, PROFIBUS-DP connector -
CAN -
CAN connector -
Serial, COM1 RS232
COM1 connector Sub-D, 9-pin, male
Serial, COM2 RS232 / RS422 / RS485
COM2 connector Sub-D, 25-pin, female
Number of USB-A interfaces 1
USB-A connector USB-A (host)
Number of USB-B interfaces -
USB-B connector -
Number of ethernet interfaces 1
Ethernet Ethernet 10/100 MBit
Ethernet connector RJ45
Integrated ethernet switch -
Technical data power supply
Power supply (rated value) DC 24 V
Power supply (permitted range) DC 20.4...28.8 V
Reverse polarity protection 9
Current consumption (no-load operation) 0.16 A
Current consumption (rated value) 0.3 A
Inrush current 75 A
I²t 0.36 A²s
Power loss 6 W
Status information, alarms, diagnostics
Supply voltage display none
Mechanical data

Manual VIPA HMI Chapter 1 Hardware description
HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30 1-11
Order number 62E-MDC0
Housing / Protection type
Material PC
Mounting mounting clips
Protect type front side IP 65
Protect type back side IP 20
Dimensions
Front panel 140 x 116 x 6 mm
Rear panel 122 x 98 x 51 mm
Installation cut-out
Width 123 mm
Height 99 mm
Minimum 2.5 mm
Maximum front panel thickness 6 mm
Weight 500 g
Environmental conditions
Operating temperature 0 °C to 50 °C
Storage temperature -20 °C to 60 °C
Certifications
UL508 certification yes

Chapter 1 Hardware description Manual VIPA HMI
1-12 HB160E - TP-ECO - RE_62E-MDC0 - Rev. 12/30