VIRTUFIT Deskbike User manual

Deskbike
User manual
EN
User manual
Ddesk bike

2
EN
VirtuFit Deskbike
INDEX
SAFETY INSTRUCTIONS
CHECKLIST
ASSEMBLY INSTRUCTIONS
LEVELING THE BIKE AND RESISTANCE
FOLDING INSTRUCTIONS
MAINTENANCE
TROUBLE SHOOTING
CONTROL PANEL
EXPLODED DRAWING
PARTS LIST
TRAINING INSTRUCTIONS
3 - 4
5
6 - 8
9
10
11 - 12
13
14 - 15
16
17 - 18
19

3EN VirtuFit Deskbike
SAFETY INSTRUCTIONS
– It is important to read this entire manual before assembling and using the device. Safe and
eective use can only be achieved if the device is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the device are informed of all warnings and
precautions.
– Before starting any exercise program, you should consult your doctor to determine if you have
any medical or physical conditions that could put your health and safety at risk, or prevent you
from using the device properly. Your doctor’s advice is essential if you are taking medication
that aects your heart rate, blood pressure or cholesterol level.
– Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, extreme shortness of breath, lightheadedness, dizziness or feelings of nausea. If you do
experience any of these conditions you should consult your doctor before continuing with your
exercise program.
– Keep children and pets away from the device. The device is designed for adult use only.
– Use the device on a solid, at level surface with a protective cover for your oor or carpet. To
ensure safety, the device should have at least 0.5 metres of free space all around it.
– Before using the device, check that the nuts and bolts are securely tightened.
– The safety of the device can only be maintained if it is regularly examined for damage and/or
wear and tear.
ATTENTION
WARNING:
Before beginning any exercise program consult your physician. This is especially
important for people who are over 35 years old or who have pre-existing health
problems. Read all instructions before using any tness equipment. Do not operate this
device without properly tted guards, as the moving parts can present a risk of serious
injury if exposed.

4
EN
VirtuFit Deskbike
SAFETY INSTRUCTIONS
– Always use the device as indicated. If you nd any defective components while assembling or
checking the device, or if you hear any unusual noises coming from the device during use,
stop immediately. Do not use the device until the problem has been rectied.
– Wear suitable clothing while using the device. Avoid wearing loose clothing that may get caught
in the device or that may restrict or prevent movement.
– The max user weight is 110 KGS. Braking ability is independent of speed.
– The device is not suitable for therapeutic use.
– Care must be taken when lifting or moving the device so as not to injure your back. Always use
proper lifting techniques and/or seek assistance if necessary.
– Please keep the space at least 1 to 2 meter at the end of base frame to escape any accidents!
– Place the device on a clean and at surface. Do not place the device on a thick carpet.
– The device is for indoor use and not for outdoor use to prevent damage. Keep the storage location
dry, clean and at. It is forbidden to use the device for purposes other than training.
– Only use the machine in an environment with an ambient temperature between 10 °C and 35 °C.
Only store the device at an ambient temperature between 5 °C and 45 °C.
Warranty claim is excluded if the cause of the defect is the result of:
– Maintenance assembly and repair work not carried out by an official dealer.
– In the event of improper use, neglect and / or poor maintenance.
– Failure to maintain the device in accordance with the manufacturer’s instructions (see the enclosed
manual).

5EN VirtuFit Deskbike
CHECKLIST
TOOLKIT
When you open the carton, and you will find the below parts in the carton:
CHECK LIST
2
Main Frame & Rear Frame
7
Saddle
24
Saddle Support
6
Exercise Monitor
16
Rear stabilizer
8
Front stabilizer
9
Adjuster Knob 26 Locking Pin
8
83
Pedal (L) 29 Pedal (R) 29
Handlebar 1
51 61 71
57
56
X4 X4 X4
X2
65
X4

6
EN
VirtuFit Deskbike
STEP 1
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and
the folding bike. Some parts (bolts, screws, etc.) are already attached to / in the folding bike.
Error message: Ensure that all cables are carefully attached. The aluminum legs are very sensitive and
must remain straight. Do you receive an error message after mounting your folding bike? Then you have to
straighten these aluminum legs again, this may cause the error message to disappear.
Socket screws: The folding bike contains socket screws, make sure that the allen key is rmly in the
bolt before you apply force to the key. In this way you prevent the head of the socket head screw from
being rotated.
STEP 1
• Assemble Rear & Front Stabilizer
• Assemble Pedals (L / R).
ASSEMBLY INSTRUCTIONS
Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and
the deskbike. Some parts (bolts, screws, etc.) are already attached to/in the deskbike.
Error message: Ensure that all cables are carefully attached. The aluminum legs are very sensitive and
must remain straight. Do you receive an error message after mounting your deskbike? Then you have to
straighten these aluminum legs again, this may cause the error message to disappear.
Socket screws: The deskbike contains socket screws, make sure that the allen key is firmly in the bolt
before you apply force to the key. In this way you prevent the head of the socket head screw from being
rotated.
• Assemble Rear & Front Stabilizer
• Assemble Pedals (L / R).

7EN VirtuFit Deskbike
STEP 2
• Assemble Saddle.
Adjust the Saddle
The Saddle Support has “Max” Sign to show
the maximum height of Saddle. You should
not exceed this height. Unscrew the Seaat
Adjustment Knob (26) a couple of turns then
pull the knob outwards to release the Seat
Support Tube (6). To get the ideal seat height
you must adhere to the following guideline;
the highest pedal should be near your knee
and the saddle should protrude just above
your waist.
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
STEP 2
• Assemble Saddle.
Adjust the Saddle
The Saddle Support has “Max” Sign to show
the maximum height of Saddle. You should
not exceed this height. Unscrew the Seaat
Adjustment Knob (26) a couple of turns then
pull the knob outwards to release the Seat
Support Tube (6). To get the ideal seat height
you must adhere to the following guideline;
the highest pedal should be near your knee
and the saddle should protrude just above
your waist.
ASSEMBLY INSTRUCTIONS
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
STEP 2
• Assemble Saddle.
Adjust the Saddle
The Saddle Support has “Max” Sign to show
the maximum height of Saddle. You should
not exceed this height. Unscrew the Seaat
Adjustment Knob (26) a couple of turns then
pull the knob outwards to release the Seat
Support Tube (6). To get the ideal seat height
you must adhere to the following guideline;
the highest pedal should be near your knee
and the saddle should protrude just above
your waist.

8
EN
VirtuFit Deskbike
STEP 3
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
STEP 3
• Assemble Exercise Monitor.
ASSEMBLY INSTRUCTIONS
• Assemble Exercise Monitor.

9EN VirtuFit Deskbike
LEVELING THE BIKE
TENSION KNOB
For security and stability, your deskbike
has a factory welded frame and once fully
assembled correctly, should not need further
alignment. However, in the interest of safety,
please always ensure that your deskbike is
positioned on a solid, flat surface. If necessary,
use a rubber mat underneath to reduce the
possibility of slipping in use. If you need to
make a fine adjustment, simply twist the end
of either Rear Frame Stabiliser Adjustable Hex
End Cap (27) to compensate for uneven floors.
To ensure smoth efficient cycling action, the
tension belt braking system on your deskbike
has been correctly adjusted by our factory
during production.
TENSION KNOB ADJUSTMENT
You could adjust the tension for varied
resistance with the Tension Control (19).
NOTE: You should begin your “Exercise
Period” at the resistance level and speed
to suit your needs. Remember to start out
slow and easy, and work your way up to the
fitness level you desire.
LEVELING THE BIKE AND RESISTANCE
LEVELING THE BIKE
LEVELING THE BIKE AND RESISTANCE
For sucurity and staility, your folding bike
has a factory welded frame and once fully
assembled correctly, should not need further
alignment. However, in the interest of safety,
please always ensure that your folding bike is
positioned on a solid, at surface. If necessary,
use a rubber mat underneath to reduce the
possibility of slipping in use. If you need to
make a ne adjustment, simply twist the end
of either Rear Frame Stabiliser Adjustable Hex
550mm
770mm
TENSION KNOB
To ensure smooth efcient cycling action, the
tension belt braking system on your folding
bike has been correctly adjusted by our
factory during production.
TENSION KNOB ADJUSTMENT
You could adjust the tension for varied
resistance with the Tension Control (19).
NOTE: You should begin your “Exercise
Period” at the resistance level and speed
to suit your needs. Remember to start out
slow and easy, and work your way up to the
tness level you desire.
LEVELING THE BIKE
LEVELING THE BIKE AND RESISTANCE
For sucurity and staility, your folding bike
has a factory welded frame and once fully
assembled correctly, should not need further
alignment. However, in the interest of safety,
please always ensure that your folding bike is
positioned on a solid, at surface. If necessary,
use a rubber mat underneath to reduce the
possibility of slipping in use. If you need to
make a ne adjustment, simply twist the end
of either Rear Frame Stabiliser Adjustable Hex
550mm
770mm
TENSION KNOB
To ensure smooth efcient cycling action, the
tension belt braking system on your folding
bike has been correctly adjusted by our
factory during production.
TENSION KNOB ADJUSTMENT
You could adjust the tension for varied
resistance with the Tension Control (19).
NOTE: You should begin your “Exercise
Period” at the resistance level and speed
to suit your needs. Remember to start out
slow and easy, and work your way up to the
tness level you desire.

10
EN
VirtuFit Deskbike
NOTE: Store your machine in a dry area away from children and high traffic areas as shown in the
illustration. Be sure it is secure and cannot fall onto small animals or children.
NOTE: Store your machine in a dry area away from children and high trac areas as shown in
the illustration. Be sure it is secure and cannot fall onto small animals or children.
FOLDING
UNFOLDING
Using the Locking Pin (3) to fold and unfold
the bike. When folded, the Locking Pin (3) is
in Positon A.
Using the Locking Pin (3) to fold and unfold
the bike. When in use, the Locking Pin (3) is
in Position B.
FOLDING INSTRUCTIONS
NOTE: Store your machine in a dry area away from children and high trac areas as shown in
the illustration. Be sure it is secure and cannot fall onto small animals or children.
FOLDING
UNFOLDING
Using the Locking Pin (3) to fold and unfold
the bike. When folded, the Locking Pin (3) is
in Positon A.
Using the Locking Pin (3) to fold and unfold
the bike. When in use, the Locking Pin (3) is
in Position B.
FOLDING INSTRUCTIONS
FOLDING
UNFOLDING
Using the Locking Pin (3) to fold and unfold
the bike. When folded, the Locking Pin (3) is
in Positon A.
Using the Locking Pin (3) to fold and unfold
the bike. When in use, the Locking Pin (3) is
in Position B.
FOLDING INSTRUCTIONS

11 EN VirtuFit Deskbike
SEMI-ANNUAL MAINTENANCE
DAILY MAINTENANCE
• Clean and remove sweat after each use. Do not use aggressive cleaning agents and ensure that
the device remains free of moisture.
• Check that the rail and the wheels under the seat are free from dust and dirt.
• Inspect all bolts and nuts in connection with moving parts of the device, tighten as required.
• Check the mobility of moving parts and components of the use equipment, silicone spray if
necessary.
Safeandeffectiveusecanonlybeachievedifthedevicewillbeassembledandmaintained
well. It is your responsibility to ensure that the equipment is regularly maintained. Parts
that are already used and / or damaged must be replaced before continuing using. The
rower machine may only be used indoors and stored away, prolonged exposure to
weathering and changes in temperature / humidity can have a serious impact on the
electrical components and moving parts of the deskbike.
MAINTENANCE

12
EN
VirtuFit Deskbike
BATTERY
MAINTENANCE
AA BATTERY
The monitor uses on “AA” battery. You can
replace the battery through the back of the
unit.
The batteries must be installed correctly. If
the screen is unreadable or only parts of the
image work, follow the next step: Remove
the batteries and wait 15 seconds, then
reinsert the batteries correctly.
ADVICE FOR HANDLING BATTERIES
CHANGING THE BATTERIES
1. Remove the batteries when they are exhausted or if you do not use the product for an extended
period of time in order to avoid hazards through leaking batteries.
2. Do not recharge batteries nor dissemble or throw then into re. Danger of explosion!
3. Pay attention to the polarity (+) and (-). Always replace all the batteries; do not mix old and new batteries,
or dierent battery types.
4. Use preferably alkaline batteries, as they have a longer operation time then usual zinc-coalbatteries.
5. A change of batteries is necessary when the display becomes weaker or completely faded.
1. If you see an improper display on the monitor, please replace the batteries to have a good result.
2. Please use 2pcs of 1.5v AA batteries as a power supply.

13 EN VirtuFit Deskbike
Display does not work
If the display no longer works, you can replace the batteries. These are at the back of the display.
Display shows no values
If the display does not show any values, you can try to check the sensor cables and the cables in the back
of the display. If this still does not work, you can move the sensor slightly.
Folding bike beeps
Check that all bolts and nuts are tightened securely. Spray silicone spray if necessary. Also check the wheels.
Squeaky exercise bike
First lubricate all rotating parts with silicone spray. It can also be that a screw is tightened too tightly or too
loosely, this creates friction and therefore a beep. If this is the case, try to nd out exactly where the beep is
coming from and then loosen or tighten this screw. The screws should be tightened in such a way that they
can always be released by hand.
Ticking noise when pedaling
This is probably caused by one of the pedals. Disassemble the trapper (s) and then reattach them to the
device. Be careful, the left-hand trapper has to be turned counterclockwise to tighten, the right-hand
trapper clockwise. Tighten the pedals securely. If this does not oer the solution, report this to the supplier.
Heart rate display does not work
This can have various causes.
• The sensor cables running from the heart rate sensor to the display are incorrectly tted or have come
o during use.
• It may be that the sensors have become damp, dirty or greasy, clean them regularly.
The console doesn’t work
• Are there any other problems? Please contact your dealer.
• When the display show Drawing D, it means the batteries need to be changed.
• If there is no signal when you pedal, please check if the cable is well connected.
Afbeelding A Afbeelding B Afbeelding C Afbeelding D
TROUBLE SHOOTING

14
EN
VirtuFit Deskbike
CONSOLE
CONTROL PANEL
BUTTON FUNCTION
CALORIES Burned calories during your exercise. 0.0 - 999.9 (cal).
MODE To select diferent functions.
TIME Workout time during your exercise. 0:00 - 99:59 (minutes).
DISTANCE Workout distance during your exercise. 0.0 - 999.9 (KM).
SPEED Workout speed during your exercise. 0.0 - 999.9 (KM/H).
BUTTON FUNCTION
MODE To select different functions.
TIME Workout time during your exercise. 0:00 - 99:59 (minutes).
SPEED Workout speed during your exercise. 0.0 - 999.9 (KM/H).
DISTANCE Workout distance during your exercise. 0.0 - 999.9 (KM).
ODOMETER Automatically counts the total distance of all training. 0 - 9999 (KM).
CALORIES Burned calories during your exercise. 0.0 - 999.9 (cal).
1. MONITOR
2. SCAN
3. CALORIES
4. MODE
5. TIME
6. DISTANCE
7. SPEED
MODE
CLEAR
48
8. CLEAR
1
57 6 32
CONTROL PANEL
1. MONITOR
2. SCAN
3. CALORIES
4. MODE
5. TIME
6. DISTANCE
7. SPEED
8. CLEAR

15 EN VirtuFit Deskbike
BUTTON FUNCTION
TIME Press the button until the TIME function is selected. The total cycling time from
the beginning to the end of the exercise is displayed.
SPEED Press the button until the SPEED function is selected. The speed is displayed
during training when you start training.
DISTANCE Press the button until the DISTANCE (DIST) function is selected. The distance from
the beginning to the end of the exercise is displayed.
CALORIES Press the button until the CALORIES (CAL) function is selected. The total calories
from the beginning to the end of the exercise is displayed.
FUNCTIONS
MONITOR
CONTROL PANEL
Operation monitor
1. When there is no signal for 3 minutes, the LCD display will turn o automatically. All function value
will be saved.
2. When there is a signal input, the monitor automatically turns on.
3. If you see an improper display on the monitor, please replace the batteries. To ensure a good result,
replace the batteries at the same time.
4. The monitor use 2pcs of 1.5v “AAA” batteries.

16
EN
VirtuFit Deskbike
EXPLODED DRAWING
EXPLODED DRAWING

17 EN VirtuFit Deskbike
#DESCRIPTION QTY
1 Handlebar 1
2 Rear frame 1
3 Locking pin 1
4 Handle grip foam 2
5 Oval line plug 3
6 Saddle support 1
7 Main frame 1
8 Rear stabilizer 1
9 Front stabilizer 1
10 Crank (R & L) 2
11 Main shaft 1
12 Lower drive wheel shaft 1
13 Magnetic bracket 1
14 Round steel 2
15 Oval pipe plug 20*40 1
16 Console 1
17 Plastic fine adjustment seat 1
18 Chain cover (U) 1
19 Tension Control Knob 1
20 EVA sticker 1
21 Screw M6 2
22 Cross head screw M6 3
23 Gear piece 2
24 Saddle 1
25 Saddle stem insert 1
26 Seat adjustment knob 1
27 Adjustable hex and cap 2
28 End cap 2
29 Pedal (R & L) 2
30 Chain cover (R & L) 2
#DESCRIPTION QTY
31 Pulley brush 2
32 Flywheel 1
33 Pulley bracket 1
34 Lower drive wheel 1
35 Upper drive wheel shaft 1
36 Upper drive wheel 1
37 Sensor bracket 1
38 Magnet 6
39 Crank guard trim 2
40 Pulley 4
41 Waved washer 5
42 Spring washer 4
43 Self-tapping screw M4*20 3
44 Screw M10 4
45 Round wire plug 1
46 Screw M5*50 1
47 Drive belt 230J 1
48 Drive belt 230J 1
49 Spring 1
50 Allen bolt M8*20 2
51 Carriage bolt M8*65 4
52 Screw M6*40 2
53 Screw M6*15 6
54 Self-tapping screw M4*20 4
55 Nut M10 2
56 Carriage bolt M8*45 2
57 Round pipe plug Φ22 2
58 Flat washer 1
59 Sensor wire 1
60 Flat washer M8 6
PARTS LIST

18
EN
VirtuFit Deskbike
#DESCRIPTION QTY
61 Dome nut M8 6
62 Nylon locknut M8 3
63 Flat washer 2
64 Outer brush 4
65 Spring washer M8 7
66 Lock ring 1
67 Bearing 1
68 Flat washer 1
69 Nylon locknut M10 1
70 Pulley 2
71 Curved washer M8 4
PARTS LIST

19 EN VirtuFit Deskbike
WARMING UP
STRETCHEN
COOLING DOWN
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down.
Do the entire program at least two and preferably three times a week, resting for a day
between workouts. After several months, you can increase your workouts to four or ve
times per week.
The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two
to ve minutes before strength-training or aerobic exercising. Perform activities that raise your heart rate
and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope,
and running in place.
Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic
training session is very important. Muscles stretch more easily at these times because of their elevated
temperature, which greatly reduces the risk of injury. Stretches should be held for 15 to 30 seconds.
The purpose of cooling down is to return the body to its normal or near normal, resting state at the end of
each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the
heart.
TOE TOUCH
INNER THIGH STRETCH
ACHILLES STRETCH
HAMSTRING STRETCH SIDE STRETCH
TRAINING INSTRUCTIONS

For questions or missing parts please contact your dealer.