VIRTUFIT Low Entry Bike 1.2i Hometrainer User manual

User manual
EN
Low Entry Bike 1.2i Hometrainer

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 2
INDEX
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
CHECKLISTCHECKLIST
ASSEMBLY INSTRUCTIONSASSEMBLY INSTRUCTIONS
ADJUSTMENTS GUIDEADJUSTMENTS GUIDE
MOVING THE BIKEMOVING THE BIKE
MAINTENANCEMAINTENANCE
TROUBLE SHOOTINGTROUBLE SHOOTING
CONTROL PANELCONTROL PANEL
APP INSTRUCTIONSAPP INSTRUCTIONS
EXPLODED DRAWINGEXPLODED DRAWING
PARTS LISTPARTS LIST
TRAINING INSTRUCTIONSTRAINING INSTRUCTIONS
3 - 4
5 - 6
7 - 10
11
12
13
14
15 - 22
23
24 - 25
26 - 27
28

EN VirtuFit Low Entry Bike 1.2i Hometrainer
3
SAFETY INSTRUCTIONS
– It is important to read this entire manual before assembling and using the device. Safe and
effective use can only be achieved if the device is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the device are informed of all warnings and
precautions.
– Before starting any exercise program, you should consult your doctor to determine if you have
any medical or physical conditions that could put your health and safety at risk, or prevent you
from using the device properly. Your doctor’s advice is essential if you are taking medication
that affects your heart rate, blood pressure or cholesterol level.
– Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular
heartbeat, extreme shortness of breath, lightheadedness, dizziness or feelings of nausea. If you do
experience any of these conditions you should consult your doctor before continuing with your
exercise program.
– Keep children and pets away from the device. The device is designed for adult use only.
– Use the device on a solid, flat level surface with a protective cover for your floor or carpet. To
ensure safety, the device should have at least 0.5 metres of free space all around it.
– Before using the device, check that the nuts and bolts are securely tightened.
– The safety of the device can only be maintained if it is regularly examined for damage and/or
wear and tear.
ATTENTION
WARNING:
Before beginning any exercise program consult your physician. This is especially
important for people who are over 35 years old or who have pre-existing health
problems. Read all instructions before using any fitness equipment. Do not operate this
device without properly fitted guards, as the moving parts can present a risk of serious
injury if exposed.

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 4
SAFETY INSTRUCTIONS
– Always use the device as indicated. If you find any defective components while assembling or
checking the device, or if you hear any unusual noises coming from the device during use,
stop immediately. Do not use the device until the problem has been rectified.
– Wear suitable clothing while using the device. Avoid wearing loose clothing that may get caught
in the device or that may restrict or prevent movement.
– The max user weight is 140 KGS. Braking ability is independent of speed.
– The device is not suitable for therapeutic use.
– Care must be taken when lifting or moving the device so as not to injure your back. Always use
proper lifting techniques and/or seek assistance if necessary.
– Please keep the space at least 1 to 2 meter at the end of base frame to escape any accidents!
– Place the device on a clean and flat surface. Do not place the device on a thick carpet.
– The device is for indoor use and not for outdoor use to prevent damage. Keep the storage location
dry, clean and flat. It is forbidden to use the device for purposes other than training.
– Only use the machine in an environment with an ambient temperature between 10 °C and 35 °C.
Only store the device at an ambient temperature between 5 °C and 45 °C.
Warranty claim is excluded if the cause of the defect is the result of:
– Maintenance assembly and repair work not carried out by an official dealer.
– In the event of improper use, neglect and / or poor maintenance.
– Failure to maintain the device in accordance with the manufacturer’s instructions (see the enclosed
manual).

EN VirtuFit Low Entry Bike 1.2i Hometrainer
5
CHECKLIST
When you open the carton, and you will nd the below parts in the carton:
TOOLKIT
NUMBER DESCRIPTION SHAPE QTY
92 Cover 1
91 Knob M8*30 1
20 Bolt M8*73 4
14 Arc Washer D8*Φ20 10
21 Cap Nut M8*H16 4
12 Bolt M8*20*S5 6
13 Spring washer D8 6
33 Knob M12 1

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 6
NUMBER DESCRIPTION SHAPE QTY
35 Knob M16 1
32 Washer D12 1
ASpanner S5 1
BWrench S13-14-15 1
TOOLKIT
CHECKLIST

EN VirtuFit Low Entry Bike 1.2i Hometrainer
7
STEP 1
Missing parts: If you think you are missing certain parts in your package, carefully check the styrofoa and
the hometrainer. Some parts (bolts, screws, etc.) are already attached to / in the hometrainer.
Error message: Ensure that all cables are carefully attached. The aluminum legs are very sensitive and
must remain straight. Do you receive an error message after mounting your hometrainer? Then you have
to straighten these aluminum legs again, this may cause the error message to disappear.
Socket screws: The hometrainer contains socket screws, make sure that the allen key is rmly in the
bolt before you apply force to the key. In this way you prevent the head of the socket head screw from
being rotated.
• Secure front bottom tube(17) to main frame(16) with bolts(20), arc washers(14) and cap nuts(21).
• Secure rear bottom tube(28) to main frame(16) with bolts(20), arc washers(14) and cap nuts(21).
ASSEMBLY INSTRUCTIONS
B - 1PC
14 - 4PCS
20 - 4PCS
21 - 4PCS
14
20
20
21
21
14
17
16
14
14
21
21
20
20
28

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 8
STEP 2
• Connect trunk wire 1(15) with trunk wire 2(37).
• Insert postbar(2) into main frame(16), then secure them with bolts(12), spring washers(13) and arc
washers(14).
• Secure pedal(27L/R) to crank(41L/R) by wrench(B).
ATTENTION: Tighten the pedals securely.
ASSEMBLY INSTRUCTIONS
13 - 6PCS
12 - 6PCS
14 - 6PCS
A - 1PCS
B - 1PC
12
13
12
13
14
12 13 14
14
37
15
27L
27R
2
37
15
41R
41L

EN VirtuFit Low Entry Bike 1.2i Hometrainer
9
STEP 3
• Secure handlebar(3) to postbar(2) with knob(91) and cover(92).
• Unlock screws(11) from computer(1).
• Insert handle pulse wire(9) into postbar(2), and connect with computer wire(1b); then connect trunk
wire 1(15) with computer wire(1a), then cover end cap(10).
• Secure computer(1) on the postbar(2) with screws(11) by wrench(B);
• Unlock bolts(94) from postbar(2), then secure bottler holder(93) to postbar(2) with bolts(94) by
wrench(B).
ASSEMBLY INSTRUCTIONS
10
2
1
1b
15
9
91 92
915
3
10
2
9
93
94
3
1a
15
1b
9
11
1a
11 - 4PCS
94 - 2PCS
92 - 1PC
91 - 1PC
A - 1PC
B - 1PC
#
#14 d8
15
1a 1b
9

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 10
STEP 4
• Insert saddle tube(34) into main frame(16), then secure with knob(35).
• Secure saddle plate(30) in the saddle tube(34) with knob(33) and washer(32).
• Secure saddle(29) in the saddle plate(30) by wrench(B).
• Insert the adapter line(38) to power hole on the back of main frame(16), then plug the adapter into
an outlet.
ATTENTION: Cut o the power source when don’t use it long time.
ASSEMBLY INSTRUCTIONS
35 - 1PC
32 - 1PC
58 1P
B - 1PC
29
30
32
33
34
35
16
38

EN VirtuFit Low Entry Bike 1.2i Hometrainer
11
WATERPAS
ADJUSTING THE SADDLE
When this product is on an uneven surface,
please adjust both Foot Pads (25) according
to the above instruction picture.
The saddle bar gives an indication of how high
the saddle can be adjusted. You are advised
not to go too high as the device can no longer
be stable. Loosen the knob under the seat
and remove the knob to release the seat post.
To get the ideal seat height you must adhere
to the following guideline; the highest pedal
should be near your knee and the saddle
should protrude just above your waist.
Rotate tension knob (37)clockwise to increase
the level of resistance, rotate the tension
control counter-clockwise to decrease the
level of resistance. Level 1 is the lowest and
level 10 is the highest.
25
91
3
ADJUSTING THE BALANCE
ADJUSTING THE HANDLEBAR
ADJUSTMENTS GUIDE

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 12
19
3
To move the machine, push the handlerbar(3)
until the transportation wheels(19) on the
front bottom tube touch the ground. With
the wheels on the ground, you can transport
the bike to the desired location with ease.
MOVING THE BIKE

EN VirtuFit Low Entry Bike 1.2i Hometrainer
13
SEMI-ANNUAL MAINTENANCE
DAILY MAINTENANCE
• Clean and remove sweat after each use Do not use aggressive cleaning agents and ensure that
the device remains free of moisture.
• Check if the device is free from dust and dirt.
• Inspect all bolts and nuts in connection with moving parts of the device, tighten as required.
• Check the mobility of moving parts and components of the use equipment, silicone spray if
necessary.
Safeandeectiveusecanonlybeachievedifthedevicewillbeassembledandmaintained
well. It is your responsibility to ensure that the equipment is regularly maintained. Parts
that are already used and / or damaged must be replaced before continuing using. The
rower machine may only be used indoors and stored away, prolonged exposure to
weathering and changes in temperature / humidity can have a serious impact on the
electrical components and moving parts of the hometrainer.
MAINTENANCE

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 14
Display shows no values
If the display does not show any values, you can try to check the sensor cables and the cables in the back
of the display. If this still does not work, you can move the sensor slightly.
Hometrainer beeps
Check that all bolts and nuts are tightened securely. Spray silicone spray if necessary. Also check the wheels.
Ticking sound when pedaling
This is probably caused by one of the pedals. Disassemble the pedal(s) and then re-assemble them on the
device. Watch out, the left pedal must be screwed counterclockwise to secure, the right pedal must be
screwed clockwise. Tighten the pedal rmly. If this is not the solution, report this to the supplier.
Heart rate display is not functioning
There can be various reasons for this:
• The sensor cables that run from the heart rate sensor to the display are not properly installed or
have become detached during use.
• The sensors may become damp, dirty or greasy. So you have to clean them regularly.
The console is not working
If there is no signal when pedaling, check if the cable is properly attached.
TROUBLE SHOOTING

EN VirtuFit Low Entry Bike 1.2i Hometrainer
15
CONSOLE
BUTTON FUNCTION
RECOVERY To testing the level of heartbeat recovery.
RESET Delete settings except the user dened U1 ~ U4, WATT, PULSE.
UP/DOWN Adjust the function value up or down.
START/STOP Start the training or resume training in stop mode.
ENTER To changeover display WATT or RPM display in the working status ;  .To
choose set items in the stop status needs to be set.
DISPLAY-ALT Lets you to select and lock on to a particular function you want.
CONTROL PANEL

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 16
FUNCTIONS
KNOP FUNCTIE
TIME The total cycling time from the beginning to the end of the exercise is displayed.
SPEED The speed is displayed during training when you start training.
DISTANCE The distance of each workout is displayed when you start exercising.
CALORIES The total calories from the beginning to the end of the exercise is displayed.
PULSE Keep your hands on the sensor for 3 seconds to display your heart rate.
RPM Revolutions per minute.
WATTS Displays the wattage.
SCAN Functions change automatically every 6 seconds.
UNIT
HEIGHT WEIGHT KPH RPM DIST CAL WATT PULSE
CM KG KM / H R / MIN KM KCAL WBPM
CONTROL PANEL

EN VirtuFit Low Entry Bike 1.2i Hometrainer
17
PROGRAM SETTINGS
PROGRAM EXPLANATION
MANUAL
MODE Program 1: adjust resistance level manually.
PROGRAM
MODE Program 2 ~ 11: Automatic resistance adjustment with preset values.
BODY FAT Program 12: Percentage of body fat, body mass index (BMI) and basal metabolism
WATT MODE Program 13: The resistance adjusts to the speed while the set wattage remains
the same.
H.R.C.
MODE
Program 14 ~ 17: The heart rate value is based on the movement mode (65%,
75%, 85%). The resistance adjusts to the speed so that the set heart rate remains
the same.
USER MODE Program 18 ~ 21: The voltage can be adjusted in dierent resistance levels.
RECOVERY
MODE Heart rate recovery status.
MANUAL MODE (PROGRAM 1)
1. Press “START” key to starting motion, or press “ENTER” key into setting.
2. In setting status, press “ENTER” key to choose setting items with relevant ashing window for
TIME, DISANCE, CALORIE, AGE.
3. Press “UP” or “DOWN” key to upward or downward a adjusted, and press“ENTER”key to next
4. Automatically exits the set status when all operations are complete, or press“START”key in the settings
status to start directly.
5. It can be adjusted the resistance value level freely during the motion status, with“UP” or “DOWN” key;
6. If time, distance, calories, or any of these are settingThe corresponding value will be inverted in motion
status. When any of setting value count to 0, t he motion will be STOP and “DI DI”Voice Prompt.
7. Press “STOP ” key to STOP the motion, in the motio.
PROGRAM EXPLANATION
CONTROL PANEL

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 18
PROGRAM MODE (PROGRAM 2-11)
1. Press “UP” or “DOWN” key to select a particular function you want.
2. Press “START” key to starting motion, or press “ENTER” key into setting mode.
3. In setting status, press “ENTER” key to choose setting items with relevant ashing window for
TIME, DISANCE, CALORIE, AGE.
4. Press “UP” or “DOWN” key to upward or downward a adjusted, and press“ENTER”key to next.
5. Automatic ally exits the set status when all operations are complete, or press“START”key in the settings
status to start directly.
6. It can be adjusted the resistance value level automatic during the motion status with program, or press
“UP”“DOWN” to manual adjustment.
7. If time, distance, calories, or any of these are settingThe corresponding value will be inverted in motion
status. When any of setting value count to 0, the motion will be STOP and “DI DI”VoicE Prompt.
8. Press “STOP ” key to STOP the motion , in the motion status.
BODY FAT (PROGRAM 12)
1. Press “ENTER” key into setting mode;
2. In setting status, press“ENTER” key to choose setting items with relevant ashing window for GENDER
- HIGHT - WEIGHT - AGE.
3. Press “UP” or “DOWN” key to upward or downward a adjusted, and press “ENTER” key to next item.
Press “START” key to starting test and. Hold the pulse sensor. Then the display will show your body fat
in 8 seconds later.
MANUAL MODE(PROGRAM 1)
CONTROL PANEL

EN VirtuFit Low Entry Bike 1.2i Hometrainer
19
4. You should keep your body relaxed and your heart rate calm.
B.M.I. (BODY MASS INDEX)
GENDER / AGE UNDER
WEIGHT HEALTY SLIGHTLY OVERWEIGHT
OVER
WEIGHT OBESE
MALE <30 < 14% 14% - 20% 20.1% - 25% 25.1% - 35% > 35%
MALE >30 < 17% 17% - 23% 23.1% - 25% 28.1% - 38% > 38%
FEMALE <30 < 17% 17% - 24% 24.1% - 30% 30.1% - 40% > 40%
FEMALE >30 < 20% 20% - 27% 27.1% - 33% 33.1% - 43 > 43%
BODY FAT
GENDER LOW MEDIUM SLIGHTLY
HIGHT HIGHT
MALE < 13% 13% - 25.9% 26% - 30% > 30%
FEMALE < 17% 17% - 23% 23.1% - 25% > 40%
B.M.R (BASAL METABOLIC RATE): The average number of calories burned per day for basic survival.
• Ref: 1300 ± 100 (22 - 40 years).
CONTROL PANEL

EN
VirtuFit Low Entry Bike 1.2i Hometrainer 20
BODY TYPE
B1 B2 B3 B4 B5 B6 B7 B8 B9
Skinny Obese Slightly
thin Slim Healthy Slightly overweight Overweight Obese Obesity
WATT MODE (PROGRAM 13)
1. Press “ENTER” key into setting mode.
2. In setting status, press “ENTER” key to choose sett ing items with relevant ashing window for
TIME - DISTANCE - WATT.
3. Press “UP” or “DOWN” key to upward or downward a adjusted, and press“ENTER”key to next.
4. Press “START” key to starting.
5. It can be adjusted the resistance value level automatic during th e motion status with WATT target
value, or press “UP”“DOWN” to manual adjustment.
6. If time, distance, calories, or any of these are settingThe corresponding value will be inverted in motion
status. When any of setting value count to 0, the motion will be STOP and “DI DI”Voice Prompt.
7. Press “STOP ” key to STOP the motion , in the motion
H.R.C MODE (PROGRAM 14-17)
1. Press “UP” or “DOWN” key to select a particular function you want.
2. Press “START” key to starting motion, or press “ENTER” key into setting mode.
3. In setting status, press “ENTER” key to choose setting items with relevant ashing window for
TIME - DISTANCE - CALORIE - AGE (only PROGRAM14 16). T.H.R (only PROGRAM17).
4. Press “UP” or “DOWN” key to upward or downward a adjusted, and press“ENTER ” key to next.
5. Press “START” key to starting.
6. It can be adjusted the resistance value level automatic during the motion status with T.H.R target
value, or press “UP”“DOWN” to manual adjustment.
7. If time, distance, calories, or any of these are setting. The corresponding value will be inverted in
motion status. When any of setting value count to 0, the motion will be STOP and “DI DI”Voice Prompt.
CONTROL PANEL