VISICO LED-200SA User manual

LED-200SA
USER GUIDE

1/ Safety Notes
A fire hazard exists if flammable materials are placed in close when the
unit is in use.
Do not restrict air vents while in use.
Avoid placing AC adapter where they can be tripped over.
Use only the original AC adapter to prevent damage to the LED light
Protect from heavy, sharp object or hot object, which may cause damage.
Never use a unit with damaged covers or damaged LED. If the unit is dropped
or damaged in any way always have it checked out before using.
Do not apply any fluids to the unit.
Damaged wires may cause a short circuit. Please replace damaged wires
promptly.
Humidity or moisture may lead to a short circuit. Operate the equipment only
in dry environments and under dry conditions.
During periods of non-use, maintenance, and assembly/disassembly work,
e.g. on the front bayonet or similar, unplug the device from the power outlet.
If your device is damaged, broken, or emits a burning smell, immediately
cut off the power by unplugging the power cord. Do not operate the device
anymore. Do not open the device. Do not attempt to repair the device on
your own. Only qualified technicians should repair the equipment.
Keep out of reach of children.
2/ Content of Carton
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
LED unit.
SF-620 Faceted Surface Standard Reflector
6m AC Adapter
Protective Cover
User guide
3/ Mounting on a Stand
Select a stand or support system of suitable weight and dimensions
to ensure stable operation of the unit.
4/ Mount/Demount a Reflector & Protective Cover
Fig.1Fig.2 Fig.3

5/ Power Supply Connections
Use only the AC adapter supplied to connect to the main power.
Before plugging the AC adapter into the wall socket, make certain that
the power switch is set to the OFF(“ O” position).
Please push the latch knob back towards the rear of the unit and rotate
the protective cap anti clockwise. Put black plastic cap aside. (Fig.1)
Install standard reflector where the protective cap was before. Align the
three pegs on the reflector with the three slots, press the reflector in and
rotate clockwise until it locks in place. (Fig.2&Fig.3)
Caution:
Always refit the protective plastic cap when transporting the unit to avoid
damaging the LED.
NEVER operate the unit with the protective plastic cap still in place.
Always switch off and disconnect from the main supply before fitting and
changing reflectors.
.
.
.
.
.
6/ Name of Parts
A. Display Screen
B. Regulator
C. Mains Power Switch
D. Angle Locking Lever
E. DC-In Connector
F. Umbrella Holder

7/ Operating the LED Light
The Mains Power Switch on the rear panel controls the power of the LED
light. Setting Mains Power Switch to “I” turns the unit ”ON”, and ”O” turns
the unit “OFF”.
DIM regulator: Power is changeable from 0% to 100%. Rotating the
Regulator clockwise will increases the LED power. Rotating Regulator
anticlockwise will decrease the LED power.
CCT regulator:Set color temperature. Rotating Regulator clockwise,
color temperature changes from 2700K-6500K. Rotating Regulator
anticlockwise, color temperature changes from 6500K-2700K.
8/ Specifications
Model No. LED-200SA
Power Output 200w
Illuminance （Lux/m）
@ color temperature 4500k
Illuminance （Lux/m）
@ color temperature 6500k）
Illuminance （Lux/m）
@ color temperature 2700k
Illuminance （Lux/m）
@ color temperature 4500k
Illuminance （Lux/m）
@ color temperature 6500k）
Illuminance （Lux/m）
@ color temperature 2700k
8200lux/m (bare lamp)
7400lux/m (bare lamp)
6500lux/m (bare lamp)
65000lux/m (with reflector)
58000lux/m (with reflector)
51000lux/m (with reflector)
Brightness dimming
Color temperature
SSI (Spectral Similarity Index)
Color rendering（CRI）
TLCI
Power supply
Power supply
0%-100%
2700K-6500K
90
≥96
≥97
100-240V, 50/60Hz
21.8*11.8*11.8cm / 8.6x4.6x4.6"
（without bracket）
21.8*13.6*20cm / 8.6x5.3x7.8"
（with bracket）

Weight
1432g / 3.15lb（main body）
1114g / 2.46lb（6m AC Adapter）
164g / 0.36lb （faceted surface
reflector）
56g / 0.12lb （Protective Cover）
★ Due to our policy of constant product improvement we reserve the
right to change equipment specifications without notice.
The picture is for reference only. Please be subject to the actual
products.
9/ VISICO LIGHT APP CONTROL
Apple mobile phone users scan the QR code
below to download the "VISICO LIGHT”APP
from the Apple App Store (supports IOS
version 9.0 or higher)
Android phone users scan the QR
code below and use a browser to
open and download the "VISICO
LIGHT" APP (supports Android
version 5.0 or higher)