VISICO LED-80T II User manual

LED-80T II
USER GUIDE

1/ Safety Notes
Do not use your LED unit in an environment where moisture or flammable vapor is
likely to come in contact with the unit.
A fire hazard exists if flammable materials are placed in close when the unit is in
use.
Do not restrict air vents while in use.
Always switch off and disconnect from the main power before changing
accessories.
Avoid placing cables where they can be tripped over. Protect from heavy, sharp
object or hot object, which may cause damage. Replace damaged cables
immediately.
Never use a unit with damaged covers or damaged LED. If the unit is dropped or
damaged in any way always have it checked out before using.
Do not apply any fluids to the unit.
Do not attempt to disassemble the unit by yourself.
Keep out of reach of children.
2/ Content of Carton
LED light
Standard reflector
Power cable
User guide
3/ Preparation Before Use
3.1 Install LED light
Select a stand or support system of suitable weight and dimensions to ensure stable
operation of the unit.

Fig.1 Fig.2 Fig.3
3.2 Release protective cover
•To remove black plastic cap, push the latch knob back towards the rear of the unit and
rotate the protective cap anti clockwise. (Fig.1)
3.3 Install light reflector
•Install standard reflector where the black plastic was before. Align the three pegs on the
reflector with the three slots, press the reflector in and rotate clockwise until it locks in
place. (Fig.2 and 3)
Note:
•NEVER operate the unit with the plastic cap still in place.
• Always refit the black plastic cap when transporting the unit to avoid damaging the LED.
•Always switch off from the main supply before fitting and changing reflectors
3.4 Adjust led light angle
Turn the knob clockwise to lock the handle, and turn the knob counterclockwise to loose
the handle. When the handle is loosen, the angle of the led light can be adjusted.
3.5 Insatll battery
There is a battery compartment on the top of the led light. Slide the top cover to open the
battery compartment (Figure 4). Then install two NP-F950/970 batteries in place (Figure 5
and Figure 6). NP-F950/970 batteries are not included in the package.
Fig.4 Fig.5 Fig.6

4/Control Panel
A LCD screen
B Regulator
C Power socket
D Umbrella holder
E Fuse
F Mains power switch
G Knob
5/ Power Supply Connections
Use only the power cord supplied or NP-F950/970 battery (not include) to connect to the
main power.

1) When using power cord, turn the switch to "AC" position to turn on the led light.
2) When using NP-F950/970 battery, turn the switch to "DC" position to turn on the led
light.
3) Turn the switch to the "OFF" position, turn off the led light
6/ Set Channel and Group
Press CH button, CH number blinks, rotate Regulator to select channel number from
01-32.
Press GR button again, GR number blinks, rotate Regulator to select group number A-E.
7/ Set Brightness
Rotate Regulator to adjust brightness 0-100%. When LED light is supplied by AC power,
maximum power is 80W. When LED light is supplied by DC power (NP-F970 batteries),
maximum power is 60W.
8/ Set Beep
Press and hold Regulator 3 seconds , LCD screen will display NO/ID. Shortly Press
regulator twice ,the LCD screen will appear BEEP. Turn Regulator clockwise to turn on
Beep. Turn Regulator counterclockwise to turn off beep.
Note: Beep only works when using remote control.
9/Light Holder with Umbrella Hole
An umbrella with a handle diameter of 8-10mm can be firmly secured in the umbrella
holder (Fig.7). Do not over tighten the screw of the umbrella holder to avoid squashing the
shaft of the umbrella. When the standard reflector is used, fit the umbrella in the hole of
the reflector.(Fig.8)
Fig.7 Fig.8
10/ Changing the Fuses

A 4A fuse is mounted on the rear panel protects the circuitry of the LED unit. Disconnect
from the main supply before changing the fuse.Never replace with a fuse of a different
type or rating.
A spare 4A fuse is fitted in the fuse holder. Use a small screwdriver to pull out the fuse
holder and change the blown fuse. (Fig.9and 10)
Fig.9 Fig.10
11/Specifications
Model
LED-80T
Power
80W
Illuminance
35300 Lux/m @6500K
(with faceted surface reflector)
Color temperature
3200K or 5600K(different unit)
Brightness
0-100
CRI
≥95
TLCI
≥97
Power supply
AC100-240V 50-60Hz or 2pc NP-F
950/970 battery (not include)
Size
21x12x12cm
Weight
1.3kg
★Due to our policy of constant product improvement we reserve the right to
change equipment specifications without notice.
VISICO LIGHT APP

Download the “VISICO LIGHT”app directly from the App Store or
the Google Play Store (iOS 9.0 or superior, Android 5.0 or
superior).