Vision Fitness E3600iNetTV User manual

Assembly
Guide
E3600iNetTV
COMMERCIAL FITNESS BIKE

1
STEP
2
STEP
3
STEP
4
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Bike. If any parts, hardware or tools are missing, please call
1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
E3600iNetTV
COMMERCIAL FITNESS BIKE

TOOLS & PARTS INCLUDED
5MM Allen Wrench 15MM Pedal Wrench
Screwdriver
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty: 1
Color-coded Hardware Bags
Assembly Guide
Warranty Card
CONSOLE BOX
iNetTV Console
Owner’s Guide

HARDWARE INCLUDED
ORANGE BAG PINK BAG
M8 x 65L Screw
Quantity: 2
BLUE BAG
M8 x 15L Screw
Quantity: 7
M8 x 20L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 Lock Washer
Quantity: 6
M8 Lock Washer
Quantity: 2

5
1
STEP
• Install the rear foot with the four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
(M8x20L). Tighten with the 5MM Allen
wrench.
ORANGE BAG
1
STEP

6
2
STEP
• Slide the rubber boot onto the
console mast.
• Locate the bundle of wires that
comes from the bracket on top of the
bike frame. Wrap these wires with the
wire tie coming from the bottom of the
console mast. Pull the wire tie and
bundle of wires up through the top of
the console mast while simultaneously
sliding the mast into the frame
bracket.
• Secure the console mast to the
frame bracket with six lock washers
(M8) and six screws (M8x15L).
Tighten with the 5MM Allen wrench.
Place the seventh screw (M8x15L) in
the rear of the frame bracket and
tighten until snug.
• Slide the console mast boot down
and snap it into place on the side
cover.
• Remove the nuts (M8) from the
screws on the bottom of the seat.
Attach the seat to the seat post with
the nuts you just removed. Tighten with
the 15MM wrench.
• Loosen the seat post knob and slide
the seat post into place in the seat
tube bracket.
BLUE BAG
2
STEP

7
3
STEP
• Feed the heart rate wires from the
handlebars through the small hole
located in the front of the console
mast. Pull these wires up through the
hole at the top of the console mast.
Attach the handlebar to the console
mast using two lock washers (M8)
and two screws (M8x20L). Tighten
with the 5MM Allen wrench.
PINK BAG
3
STEP

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z36CB40-AG1824PRD
AG18.24PRD
REV1
4
STEP
• Remove the six mounting screws
from the back of the console with the
Phillips screwdriver. Set the console in
place and secure it to the console
mast with the screws you just
removed. Connect all the wires to the
proper locations in the back of the
console (see diagram).
• With the Phillips screwdriver remove
the two screws located half way up
the console mast. Attach the water
bottle bracket to the console mast with
the two screws. Insert the water bottle.
CONSOLE
4
STEP
1 - Co-Axial Cable TV
2 - USB - B
3 - USB - A
4 - VGA (PC Video)
5 - Video IN
6 - Audio - R
7 - Audio - L
8 - Microphone
9 - Heart Rate Reciever 1
10 - Heart Rate Reciever 2
11 - 20 Pin Connector
12 - Power Plug
13 - Miles/Kilometers Switch
14 - Data Port
1 2 3 4 5 6 7 8
14
9
10
11
12
13
WIRES