Vision Fitness E3000 User manual

Assembly
Guide
E3100 AND E3000
UPRIGHT FITNESS BIKES

1
STEP
2
STEP
4
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosen-
ing and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
E3100 AND E3000
UPRIGHT FITNESS BIKES
3
STEP

5mm T-Shaped Wrench 15mm Pedal Wrench
Screwdriver
5mm L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Water Bottle & Bracket
Power Supply (E3100 ONLY)
Tension Control Knob and bracket
(E3000 ONLY)
Pedals
Seat Post Knob
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
14mm Seat Wrench

ORANGE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 20L Screw
Quantity: 2
M8 Lockwasher
Quantity: 4
M5 x 70L Screws
Quantity: 1
(E3000 ONLY)
M8 x 15L Screw
Quantity: 7
M8 Lockwashers
Quantity: 8
M8 x 65L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M5 x 15L Screw
Quantity: 2
M5 Washer
Quantity: 1
(E3000 ONLY)

5
1
STEP
• Slide the rear foot into place and insert
two screws (M8x20L) with two
lock washers (M8) to the outside holes.
Insert two screws (M8x65L) with two lock
washers (M8) to the inside holes. Tighten
all screws with the 5mm T-Shaped
wrench.
ORANGE BAG
1
STEP
Rear Foot

6
E3000 ONLY 2
STEP
Tension Knob
Tension Knob
Bracket
Console Mast
Console Mast
Cover
Mounting
Bracket
2
STEP
• Slide the console mast cover onto
the console mast.
• With the included wire-tie, pull the
wire harness, or sensor wire through
the console mast. Insert the console
mast into the mast mounting-bracket.
Secure in place with seven screws
(M8x15L) and six lock washers (M8).
Tighten with the 5mm T-Shaped
wrench. NOTE: The screw facing the
seat does not use a lock washer.
Tighten this screw until snug with the
5mm L-Shaped wrench. Slide the con-
sole mast cover down over the screw
heads.
• MODEL E3000: Snap the tension
knob mounting bracket onto the ten-
sion knob. Turn the tension knob to
level 16. Connect the cable to the ten-
sion cable located inside the console
mast. Secure the tension knob to the
console mast with the washer (M5)
and screw (M5x70L). Tighten with
screwdriver.
• Slide the heart rate wires of the han-
dlebar through the hole in the handle-
bar bracket on the console mast.
Secure the handlebar onto the
handlebar bracket with two screws
(M8x20L) and two lock washers (M8).
Tighten with the 5mm T-Shaped
wrench.
• Remove the four mounting screws from
the back of the console. Connect the
wire harness and the heart rate wires to
the console. Attach the console to the
console mast using the four mounting
screws that were just removed.
• E3000 ONLY: Insert the two AA bat-
teries into the console.
• Attach the water bottle cage to the
console mast with two screws
(M5x15L) using the screwdriver. Insert
the water bottle into the cage.
PINK BAG
E3100 ONLY
Console
Water Bottle
Cage

7
3
STEP
Seat Post
Seat Post
Cover
3
STEP
• Slide the seat post cover onto the
seat post
• Slide the seat post into the frame and
lower the seat post cover into place.
• Insert the adjustment knob through the
seat post cover and tighten in place.
• Attach the seat to the seat post by
tightening the 14mm nuts on the
underside of the seat.
GREEN BAG

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2005 Vision Fitness. All Rights Reserved. 5.05 Part #Z30CB112-AG
AG18.18PRD
REV4
4
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15mm pedal wrench.
PEDALS
4
STEP