Vision Fitness R2600HRC User manual

MODEL R2600HRC SEMI-RECUMBENT
FITNESS
VISION
Guide
Assembly

To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding though,
enter your new Fitness Cycle’s serial number here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Fitness Cycle, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
Before you begin…
semi-recumbent fitness cycle
R2600HRC
5
STEP
1
STEP
3
STEP
2
STEP
4
STEP
6
STEP

BLACK BAG
20MM L x 8MM D Bolt
Quantity: 4
BLUE BAG
20MM L x 8MM D Bolt
Quantity: 4
M8 x 1.5T Washer
Quantity: 4
5MM Allen Wrench
13MM Wrench Screwdriver
TOOLS & HARDWARE INCLUDED
4MM Allen Wrench
5MM L-Shaped Wrench

ORANGE BAG
55MM L x 8MM D Bolt
Quantity: 2
HARDWARE INCLUDED
NyLock Nut
Quantity: 2
PINK BAG
20MM L x 8MM D Bolt
Quantity: 6
M8 x 1.5T Lock Washer
Quantity: 4
GREEN BAG
Seat Frame End Cap Bolt
Quantity: 2
Seat Stop Parts
55MM L x 6MM D Bolt
Quantity: 4
Seat Rail End Cap Screw
Quantity: 2
M6 x 1.0T Lock Washer
Quantity: 4 Plastic Strap Quantity: 2

5
1
STEP
• Install the rear foot with the four
bolts, using the Blue 5MM Allen wrench.
BLACK BAG 1
STEP
2
STEP
• Slide the rubber cover onto the
console mast.
• Unfold the wire and attach it to the
string located inside the mast. Guide
the wire up through the mast while
simultaneously sliding the mast onto
the frame bracket.
• Bolt the mast to the frame using the
two bolts and two nuts; make sure
these are tight!
• Slide the rubber cover down over
the bolt heads.
• Bolt the waterbottle cage to the
console mast using the two bolts
located in the mast.
ORANGE BAG
2
STEP
3
STEP
• Mount the upper handlebars to the
console mast using the four bolts and
four washers.
BLUE BAG 3
STEP

6
4
STEP
• Remove the four screws from
the back of the console. Plug the
wire connector from inside the mast
into the console. The cable connector
is slotted, so it may only be connected
one way; do not force it!
• Mount the console to the mast using
the four screws. Do not pinch the
cable!
CONSOLE 4
STEP
5
STEP
• Slide the seat frame onto the seat
rail and lift the seat lever, so the seat
frame will slide to the front of the seat
rail.
• Mount the side handlebars to
the seat frame using four bolts
(15MM L x 8MM D) and four lock washers
(M8 x 1.5T).
• Mount the indicator plate onto
the seat frame using two bolts
(15MM L x 8MM D).
PINK BAG
5
STEP

7
6a
6b
6
STEP
Connect the seat mount
handlebar wire harness (a) and the
seat rail wire harness (b) together. The
wire harness connectors are slotted,
so they may only be connected one
way; do not force them!
• Lift the seat lever and slide the seat
frame to the back end of the seat rail,
pulling the seat rail wire harness tight,
but not overly tight. Secure the wire
harness using the plastic strap located
at the end of the seat frame.
• Attach one seat stop to the seat stop
axle using the included bolt and
washer. Slide this seat stop assembly
through the hole in the seat rail. Attach
the other end of the seat stop with the
other included bolt and washer.
• Press the seat frame end cap into
the seat rail and secure with two bolts
(55MM L x 8MM D).
• Mount the seat rail end cap onto the
seat frame with two screws.
Secure the wire harness using
the plastic strap located in the middle
of the seat frame.
• Mount the bottom seat pad with
four bolts (55MM L x 6MM D) and four
lock washers (M6 1.0T), using the
Black-handled 4MM Allen wrench.
GREEN BAG 6
STEP
6a
6b
621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2000 Vision Fitness. All Rights Reserved. 5.00 Part #Z26RB35-001
REV2