Vision Fitness R2000 User manual

Guide
Assembly
R2000
SEMI-RECUMBENT FITNESS CYCLE

semi-recumbent fitness cycle
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding though,
find your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle, to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL nuts and screws are in place and partially threaded in before
completely tightening any ONE screw.
R2000
2
STEP
1
STEP
3
STEP
4
STEP
5
STEP

5MM Allen Wrench
15MM Pedal Wrench
Screwdriver
4MM L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Seat Rail Cover, Qty: 1
Tension Knob and bracket, Qty: 1
Water Bottle and Cage, Qty: 1
Water Bottle Bracket, Qty: 1
Parts Bags
Assembly Guide
Owner’s Manual
Warranty Card

HARDWARE INCLUDED
BLUE BAG
PINK BAG
ORANGE BAG
GREEN BAG
M8 x 15L Screw
Quantity: 3 M8 Lock Washer
Quantity: 3
M8 x 15L Screw
Quantity: 4 M8 Lock Washer
Quantity: 4 M8 x 15L Screws
Quantity: 4
M8 x 15L Screw
Quantity: 5
M6 x 55L Screws
Quantity: 8
M8 Lock Washer
Quantity: 4
M6 Lock Washer
Quantity: 8
M5 x 15L Screw
Quantity: 2
M5 x 60L Screw
Quantity: 1
M5 x 22L CapScrew
Quantity: 2

5
1
STEP
2
STEP
1
STEP
• Slide the seat frame onto the seat rail.
• Connect the rail support to the
bottom of the seat rail. Attach with
four screws (M8x15L) and four lock
washers (M8). Tighten with the 5MM
Allen wrench.
ORANGE BAG
2
STEP
• Slide the front seat rail cover on the
seat rail.
• Insert the front end of the seat rail
into the frame bracket. Secure the seat
rail to the frame with three screws
(M8x15L) and three lock washers
(M8). Tighten with the 5MM Allen
Wrench.
• Slide the front rail cover into
position at the front of the seat rail.
BLUE BAG

6
3
STEP
3
STEP
• Put the seat handlebar onto the seat
frame. Attach with four screws
(M8x15L) and four lock washers
(M8), using the 5MM Allen wrench.
• Secure the seat cushions to the seat
frame by inserting the eight screws
(M6x55L) and eight lock washers
(M6). Tighten with the 4MM L-shaped
wrench.
PINK BAG

7
4
STEP
4
STEP
• Slide the mast cover onto the
console mast.
• With the included wire tie, pull the
console cable and sensor wire
through the console mast. Place the
console mast into the console mast
mounting bracket. Secure the mast to
the bracket with 5 screws (M8x15L)
and lock washers (M8) and tighten
with the 5MM Allen wrench. Note: The
screw facing the seat does not use a
lock washer. Tighten this screw only
until snug. Slide the console mast
cover down over the screw heads.
• Turn the tension knob to level 15.
Direct the cable on the tension knob
through the tension knob bracket.
Attach the cable to the tension cable
located in the console mast. Secure
the tension knob to the console
mast with the screw (M5x60L) and
screwdriver.
• Remove the four screws from the
back of the console. Plug the sensor
wire into the console. Mount the con-
sole onto the console mast with the
four screws.
• Secure the water bottle bracket
to the console mast with the 4MM
L-shaped wrench and two cap screws
(M5x22L). Attach the water bottle
cage to the bracket with two screws
(M5x15L) using the screwdriver. Insert
the water bottle into the cage.
GREEN BAG

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 5.01 Part #Z20RB44-AG1809PRD
AG18.09PRD
REV2
5
STEP
5
STEP
• Attach the left and right pedals to
the left and right crank arms. Tighten
using the 15MM pedal wrench.
PEDALS