Vision Fitness R2200HRT User manual

Assembly
Guide
R2200HRT
SEMI-RECUMBENT FITNESS CYCLE

1
STEP
2
STEP
3
STEP
4
STEP
To avoid possible damage to this Fitness Cycle, please follow these assembly steps in the correct order. Before proceeding, find
your new Fitness Cycle’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
R2200HRT
SEMI-RECUMBENT FITNESS CYCLE

TOOLS & PARTS INCLUDED
5MM Allen Wrench 15MM Pedal Wrench
Screwdriver
5MM L-Shaped Wrench
4MM L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Pedals, Qty: 2
Power Supply, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6MM L-Shaped Wrench

HARDWARE INCLUDED
ORANGE BAG BLUE BAG
PINK BAG
M8 x 20L Screws
Quantity: 2
M8 x 65L Screw
Quantity: 2
M8 Lockwashers
Quantity: 4 M8 x 20L Screws
Quantity: 4
M8 x 15L Screws
Quantity: 4
M8 Lockwashers
Quantity: 4
M6 Lockwashers
Quantity: 8
M6 x 55L Screws
Quantity: 8
M8 x 15L Screws
Quantity: 5
M8 x 20L Screws
Quantity: 2
M8 Lockwashers
Quantity: 6

5
1
STEP
1
STEP
• Slide the rear foot in place and
attach two screws (M8 x 20L), two
screws (M8 x 65L), and four lock
washers (M8), using the blue-handled
5MM Allen wrench.
• Slide the rubber sleeve to the proper
position at the bottom of the joint.
ORANGE BAG
2
STEP
2
STEP
• Place the seat bracket on the seat
frame. With the 6MM Allen wrench
secure the seat bracket with the four
screws (M8 x 20L).
• Loosen and take off the screw on
the seat lever with the 4MM Allen
wrench. Turn the seat lever so the
screw holes line-up and reinstall the
screw with the 4MM L-shaped Allen
wrench to secure the seat lever.
• Place the seat handlebar into the
proper position on the seat frame.
With the 5MM Allen wrench secure the
seat handle bar with four screws
(M8 x 15L) and four lock washers
(M8).
• This product features a lumbar
control seat. To secure this seat to the
frame, remove the plastic cover from
the back of the upright seat cushion.
Use the four screws (M6 x 55L) and
four lock washers (M6) to attach
the cushions to the frame. Tighten with
the 4MM L-shaped Allen wrench. Snap
the plastic cover onto the back of the
upright seat cushion.
BLUE BAG

6
3
STEP
• Slide the console mast cover over
the console mast. Guide the console
cable up through the bottom of the
console mast with the attached wire.
• Slide the console mast into the
console mast mounting bracket and
use the 5MM Allen wrench to secure the
five screws (M8x15L) and lock
washers (M8). Note: The screw
facing the seat does not use a lock
washer. Tighten this screw only until
snug.
• Slide the console mast cover to the
proper position. Attach the front
handlebar to the console mast. Use
the 5MM Allen wrench to tighten the two
screws (M8x20L) and lock washers
(M8) to secure the handlebar.
• Take out the four screws (M5x12L)
from the back of the console with the
Phillips screwdriver. To attach the
console, plug in the console cable to
the proper position in the back of the
console. Reinsert the four screws
(M5x12L) with the Phillips screwdriver
to secure to the console mast.
• Use the Phillips screwdriver to
attach the water bottle cage to the
console mast with the two included
screws (M5x15L). Insert the water bottle.
PINK BAG
3
STEP

7
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 7.02 Part #Z22RB42-AG1816PRD
AG18.16PRD
REV1
4
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15MM pedal wrench.
PEDALS
4
STEP