Vision Fitness R2000 User manual

ASSEMBLY INSTRUCTIONS
R2000
To avoid possible damage to this Fitness Cycle,
please follow these assembly instructions.
Carefully remove all its parts from the box,
lay them out and review the parts list.
If any parts are missing, please call 1-800-335-4348, Ext 12
Before proceeding, find your Fitness Cycle’s serial number,
located on the underside of main frame, and enter here:
Refer to this number when calling for service.
IT ALL STARTS WITH A VISION

R2000 Parts Diagram
125
130
523

VISION FITNESS R2000 Parts Description
Part # Description Count Dimensions
Rear Foot and Seat Support Parts
#106 Rear Foot Assembly 1
#182 Top Attachment Bolts 7 20mm L x 8mm D
#184 Top Attachment Washers 7
#91 Bolt Plate 1
#96 Seat Rail Support Post 1
#186 Support Post Bolts-Bottom 4 60mm L x 8mm D
#121 Seat Rail 1
Seat Parts
#115 Seat Frame 1
#137 Seat Cushion Back 1
#136 Seat Cushion Bottom 1
#195 Seat Cushion Bolts 8 55mm L x 6mm D
#196 Seat Cushion Bolt Washers 8
#110 Seat Mount Handlebars 1
#182 Handlebar Attachment Bolts 4 20mm L x 8mm D
#184 Handlebar Attachment Washers 4
#133 Rubber Seat Rail Cap 1
#520 Seat Knob 1
#523 Seat Rail End Cap 1
Console Parts
#101 Console Mast 1
#182 Console Mast Attachment Bolts 6 20mm L x 8mm D
#184 Console Mast Attachment Washers 6
153 Console 1
#75 RPM Sensor Wire 1
#88 Console Mast Rubber Cover 1
Other Parts
#152 Pedals 2
#199 Pedal Straps 2
#130 Tension Knob and Cable 1
#125 Tension Knob Bolt 1
R2000 Parts

Step 2 • Seat Rail
1: Place the Seat Rail (121) on the Seat Rail Support (96). Thread the four
Attachment Bolts (182) with Washers (184) through the top of the Seat
Rail Support (96) into the Seat Rail (121).
2: Slide the Seat Frame (115) onto the Seat Rail (121) from the front of the
Seat Rail. After the Seat Frame (115) is on the Seat Rail (121) insert the
Seat Knob (520) into a hole to prevent the Seat Frame (115) from sliding
forward.
3: Slip the Rubber Seat Rail Cap (133) onto the front end of the Seat Rail
(121), slide the Rubber Seat Rail Cap (133) back to expose the three front
attachment bolt holes.
4: Place the Seat Rail Assembly (121) into the main frame bracket. Thread the
three Attachment Bolts (182) with Washers(184) through the Seat Rail
(121) in the main frame bracket. Tighten all Attachment Bolts (182)
securely to the main frame bracket. Slide down the Rubber Seat Rail Cap
(133) until it is flush with the side covers.
5: Place the seat rail end cap over the rear end rail and snap to the top of the
seat rail end post.
Note: ALWAYS HOLD THE SEAT KNOB OUT WHEN ADJUSTING THE SEAT
HEIGHT. TURN THE INNER KNOB CLOCKWISE TO LOCK IN PLACE.
R2000 Assembly
Step 1 • Seat Support and Rear Foot
1: Attach the Seat Rail Support Post (96) to the top of the Rear Foot Assembly
(106) with four Bottom Support Post Bolts (186), four Washers (184) and
Bolt Plate (91). Tighten with a 5mm allen wrench.
FRONT VIEW
SIDE VIEW
96
121
182
184
523
END CAP

Step 3 • Seat Assembly
1: Secure the Seat Mount Handlebars (110) to the Seat Frame (115) with four
Seat Attachment Bolts (182) and Washers (184).
2: When mounting the Seat Cushion Bottom (136), you have two sets of
holes to choose from. Using the rear set of holes is recommended for
most people. For a smaller person, you may choose to use the forward set
of bolt holes. Mount the Seat Cushion Bottom (136) to the Seat Frame
(115) with four of the Seat Cushion Bolts (195) and Seat Cushion Bolt
Washers (196). Do not fully tighten any bolt until all four bolts are started.
3: Mount the Seat Cushion Back (137) to the Seat Frame (115) using the
remaining four Seat Cushion Bolts (195) and Washers (196). Do not fully
tighten any bolt until all four bolts are started.
R2000 Assembly

Step 4 • Pedals
1: Identify the left and right Pedals (152) and the left and right Pedal Straps(199). Attach the correct
straps to each pedal, then thread each Pedal into the correct left and right crank arms and tighten.
The Pedals and Straps are marked with either an L or an R.
NOTE: IT IS VERY IMPORTANT TO FULLY TIGHTEN EACH PEDAL. FAILURE TO DO SO WILL RESULT
IN LOOSENING AND NOISE. USE THE WRENCH PROVIDED OR A 15MM OPEN END WRENCH.
Step 5 • Console Mast
1: Unfold the RPM Sensor Wire (75) that is folded into the top frame bracket.
Straighten this wire and remove any kinks by drawing the cable through your fingers.
2: Slip the Tension Knob cable (130) along with the RPM Sensor Wire (75)
through the Rubber Console Mast Cover (88), then rest the Rubber Console Mast Cover
over the top frame bracket.
3: Holding the Console Mast (101) above the top frame bracket, guide the RPM Sensor
Wire (75) through the Console Mast while simultaneously sliding the Console Mast onto
the top frame bracket.
4: Slide the Rubber Console Mast Cover (88) up to expose the bolt holes in the Console
Mast (101), then bolt to the frame using six Attachment Bolts (182). Make sure all these
bolts are tight. Now slide the Rubber Console Mast Cover (88) back down to cover the
bolt heads.
R2000 Assembly
125
130

Step 6 • Cable Connection
1: Locate the Tension Knob and upper cable assembly (130). Turn the Tension Knob to
position 1. Reach inside the opening of the Console Mast (101) and connect the
Upper Magnet Shift Cable (130) to the lower cable hook-slide on the end of the
Lower Magnet Shift Cable (66), as shown in the accompanying illustrations.
2: Insert the cable through the slot and draw the tension cable with the copper end
(130) into the metal bracket notch (131) and insert the cable.
3: Push the cable into the console mast (101). Insert the tension knob assembly to the
console mast. Attach bolt (125) through the front of the console mast and tighten
down the tension knob assembly.
R2000 Final Assembly
Step 7 • Console
1: Plug the RPM Sensor Wire (75) into the Console (153). DO NOT PINCH the RPM Sensor Wire between the
Console (153) and the Console Mast (101). Make sure the Sensor Wire fits in the slot cut in the
Console Mast Mount.
2: Mount the Console (153) to the Console Mast (101) using the two Console Attachment Bolts found in
the back of the Console.
Step 8 • Install Batteries and Test Operation
1: Remove the battery compartment lid on the back of the Console (153) and install the Batteries. Two AA
Batteries are required.
2: Test ride the bike and make sure that all console feedback functions are operational.
153
75
101
NOTE: When the tention knob
(130) is inserted into the con-
sole mast (101) the Upper
Magnet Shift Cable (130) must
be placed in the top of the
console mast (101), between
the tension knob (130) and
the console (153).
130

621-D East Lake Street
P.O. Box 280
Lake Mills, WI 53551
[phone]