Vision Fitness R2000 User manual

Assembly
Guide
R2100 AND R2000
SEMI-RECUMBENT FITNESS BIKES

1
STEP
2
STEP
4
STEP
5
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosen-
ing and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
R2100 AND R2000
SEMI-RECUMBENT FITNESS BIKES
3
STEP

5mm T-Shaped Wrench 15mm Pedal Wrench
Screwdriver
5mm L-Shaped Wrench
TOOLS & PARTS INCLUDED
4mm L-Shaped Wrench
PARTS BOX
Console Mast Cover
Pedals
Seat Rail Cover
Tension Knob and bracket
(R2000 ONLY)
Water Bottle & Cage
Warter Bottle Bracket
(R2000 ONLY)
Power Supply
(R2100 ONLY)
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card

BLUE BAG
ORANGE BAG
GREEN BAG
HARDWARE INCLUDED
M8 x 15L Screw
Quantity: 4
M8 Lockwasher
Quantity: 4
M5 x 65L Screw
Quantity: 1
(R2000 ONLY)
M8 x 15L Screws
Quantity: 5
M8 Lockwashers
Quantity: 4
M5x35L CapScrew
Quantity: 2
(R2000 ONLY)
M6 x 35L Screws
Quantity: 8
M8 x 15L Screw
Quantity: 3
M8 Lockwasher
Quantity: 3
M8 x 15L Screw
Quantity: 4
M8 Lockwasher
Quantity: 4 M6 Arc Washer
Quantity: 8
M5 Washer
Quantity: 1
(R2000 ONLY)
M5 x 10L Screws
Quantity: 1
PINK BAG
Rubber Stopper
Quantity: 1

5
1
STEP
• Attach the rear support to the seat rail
with four screws (M8x15) and four lock
washers (M8). Tighten with the 5mm
T-shaped wrench.
• Slide the seat frame onto the seat
rail. Make sure the flat side of the
clamp block rests against the bottom
of the seat rail.
• Insert the heart rate wires located
under the seat frame through the hole
on the bottom of the seat rail and push
them toward the front of the rail. Take
the end of the heart rate wires that
runs through the seat rail and insert
them through the hole in the bracket at
the end of the rail. Snap the wire grip
around the end of the heart rate wires
and slide it into place on the bracket.
• Attach the rubber stopper to the bot-
tom of the seat rail with the (M5x10)
screw.
ORANGE BAG
1
STEP
CORRECT INCORRECT
Seat Frame
Seat Rail
Rail Support
Wire Grip

6
2
STEP
• Slide the seat rail sleeve onto the
seat rail.
• Connect the heart rate wires com-
ing from the seat rail to the heart rate
wires coming from the seat frame
bracket. Tuck the excess wire under
the seat frame bracket.
• Slide the seat rail onto the seat rail
bracket. Secure with three screws
(M8x15) and three lock washers (M8).
Tighten with the 5mm T-shaped wrench.
• Slide the seat rail sleeve into posi-
tion at the front of the seat rail.
BLUE BAG
2
STEP
Frame Bracket
Seat Rail Sleeve

7
3
STEP
• With four screws (M8x15) and four
lock washers (M8) attach the seat han-
dlebar to the seat frame.
• Connect the heart rate wires coming
from the seat handlebar to the heart rate
wires on the seat frame.
• Mount the backrest and the seat
cushion to the seat frame using eight
screws (M6x35) and eight arc wash-
ers (M6). Tighten with the 4mm L-
shaped wrench.
PINK BAG
Seat Handlebar
3
STEP

8
4
STEP
• Slide the mast cover onto the
console mast.
• With the included wire tie, pull the
console cable, or sensor wire, and
heart rate wires, through the console
mast. Place the console mast into the
console mast mounting bracket.
Secure the mast to the bracket with
five screws (M8x15L) and four lock
washers (M8) and tighten with the
5mm T-shaped wrench. NOTE: The
screw facing the seat does not use a
lock washer. Tighten this screw until
snug. Slide the console mast cover
down over the screw heads.
• R2000 ONLY: Turn the tension knob
to level 16. Direct the cable on the
tension knob through the tension knob
bracket. Attach the cable to the
tension cable located in the console
mast. Secure the tension knob to the
console mast with the washer (M5)
and screw (M5x65L). Tighten with the
screwdriver.
• Remove the four screws from the
back of the console. Plug the wire
harness and heart rate wires into the
console. Mount the console onto the
console mast with the four screws.
• R2000 ONLY: Insert the two AA bat-
teries into the console.
• Remove the two M5x15L Screws
from the water bottle cage holes on
the console mast.
• R2000 ONLY: Secure the water
bottle bracket to the console mast with
the 4mm L-shaped wrench and two
cap screws (M5x35L). Attach the
water bottle cage to the bracket with
two screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
• R2100 ONLY: Attach the water
bottle cage to the console mast with
two screws (M5x15L) using the
screwdriver. Insert the water bottle into
the cage.
GREEN BAG
4
STEP
R2000
R2100
Mast Cover
Console Mast
Mounting
Bracket
Waterbottle
Bracket

9
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
©2004 Vision Fitness. All Rights Reserved. 5.05 Part #Z20RB104-AG
AG18.17PRD
REV5
5
STEP
• Attach the left and right pedals to
the left and right crank arms, tighten
using the 15mm pedal wrench.
PEDALS
5
STEP