Vision Fitness R10 User manual

R10 ASSEMBLY GUIDE
TOOLS & PARTS INCLUDED
ASSEMBLY GUIDE
HARDWARE INCLUDED
R10 Semi-Recumbent Fitness Bike
1600 Landmark Drive • Cottage Grove, WI 53527
toll free 800.335.4348 • fax [phone]
www.visionfitness.com
©2012 Vision Fitness. All Rights Reserved.
2012.06.18
REV1.2
SW8 Lock Washer
Quantity: 4
M8 x 15L Bolt
Quantity: 2
SW8 Lock Washer
Quantity: 2
M8 x 15L Bolt
Quantity: 4
M8 x 10L Set Screw
Quantity:1
Wire Grip
Quantity: 1
M5 x 10L Bolt
Quantity: 1
Rubber Stopper
Quantity: 1
M8 x 15L Bolt
Quantity: 4
SW8 Lock Washer
Quantity: 4
M6 x 35L Bolt
Quantity: 8
M6 Arc Washer
Quantity: 8
M8 x 15L Bolt
Quantity: 4
SW8 Lock Washer
Quantity: 4
M8 x 15L Bolt
Quantity: 3
SW8 Lock Washer
Quantity: 3
M8 x 20L Bolt
Quantity: 2
SW8 Lock Washer
Quantity: 2
PINK BAG
GREEN BAG
ORANGE BAG
BLUE BAG
BLACK BAG
5mm T-Shaped Wrench 17mm/15mm Pedal Wrench
Screwdriver
5mm L-Shaped Wrench
4mm L-Shaped Wrench
Power Supply
Water Bottle Cage
Color Coded Hardware Bags
Assembly Guide
PARTS BOX

Seat Rail
Wire Grip
Rubber Stopper
Bottom Frame
Support Tube
Seat Frame
Heart Rate
Wires
Heart Rate
Wires
Rear Support
Foot
Seat Rail
Bracket
Assembly
Guide
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before
proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service. Be sure to read your Owner’s Guide before using your new
Fitness Bike. If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your
Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws
are in place and partially threaded in before completely tightening any ONE bolt or screw.
R10
Semi-Recumbent Fitness Bike
STEP 2
• Attach rear support foot to the bottom
of the seat rail with four (M8x15L) bolts
and four (SW8) lock washers. Do not
tighten completely.
• Slide the seat frame onto the seat
rail. Make sure the flat side of the
clamp block rests against the bottom
of the seat rail. Also make sure the
adjustment handle is facing forward.
• Insert the heart rate wires located
under the seat frame through the hole
on the bottom of the seat rail and push
them toward the front of the rail. Take
the end of the heart rate wires that run
through the seat rail and insert them
through the hole in the bracket at
the end of the rail. Snap the wire grip
around the end of the heart rate wires
and snap it into place in the bracket.
• Attach the rubber stopper to the bottom
of the seat rail with the (M5x10L) bolt.
Tighten with the screwdriver.
BLUE BAG
STEP 1
• Connect bottom frame support tube
to main frame with two (M8x15L) bolts
and two (SW8) lock washers. Tighten
with the 5mm T-handle wrench.
ORANGE BAG
STEP 6
• Attach left and right pedal straps to
left and right pedals.
• Attach left and right pedals to left and
right crank arms. NOTE: both pedals
and crank arms should be labeled left
or right. Tighten with the included
pedal wrench.
• Plug in power supply to power socket
on the front side of the bike.
PEDALS
STEP 3
• Connect the heart rate wires coming
from the seat rail to the heart rate
wires coming from the main frame.
• As you slide the seat rail onto the seat
rail bracket, slide any excess heart rate
wire into the seat rail bracket. Slide
the seat rail on so the holes on the
bottom of the bracket are in line with
the frame. Insert three (M8x15L) bolts
with three (SW8) lock washers into
the holes for support. Do not tighten
completely.
• Connect the bottom frame support
tube to the bottom of the rear support
foot with two (M8x20L) bolts and two
(SW8) lock washers. Tighten with the
5mm T-handle wrench.
• Go back and tighten all bolts with
the 5mm T-handle or 5mm L-shaped
wrench.
PINK BAG
STEP 4
• Slide the console mast cover onto the
console mast.
• Wrap the wire tie that comes from the
bottom of the console mast around
the end of console cable and around
the heart rate wires that are sitting in
the frame console mast bracket. Slowly
pull the wire tie up through the console
mast until the cable and wires come
through the top of the mast. Slide
the bottom of the console mast over
the frame mast bracket. Attach the
mast to the frame with four (M8x15L)
bolts, four (SW8) lock washers and
one (M8x10L) set screw and slide the
console mast grommet down over the
bike frame.
• Remove the four bolts from the back
side of the console. Plug the console
cable and heart rate wires into the back
side of the console. Place the console
onto the mounting plate of the console
mast and re-insert the four mounting
bolts. Tighten with the screwdriver.
• Remove the two bolts from the
backside of the console mast. Attach
the water bottle cage to the mast
with these two bolts. Tighten with the
screwdriver.
GREEN BAG
STEP 7
• Refer to Product Selection and Model
Configuration decal on console or
follow these steps.
• Once the product is plugged in turn on
the console
• Select bike (BK) using the resistance
arrow keys. Press ENTER to select.
• Select model (R10) using the
RESISTANCE arrow keys. Press ENTER
to select. Console will reset to start-up
screen.
• The product selection and model
configuration is now complete.
CONSOLE
STEP 5
• Connect the Heart Rate wires from
the seat handlebar to the heart rate
wires from the seat frame. Attach
seat handlebar to seat frame with four
(M8x15L) bolts and four (SW8) lock
washers. Tighten with 5mm T-shaped
wrench.
• Attach seat bottom cushion to seat
frame with four (M6x35L) bolts and
four (M6) arc washers. Tighten with the
4mm L-shaped wrench.
• Attach the seat back cushion to the
seat frame with four (M6x35L) bolts
and four (M6) arc washers. Tighten
with the 4mm L-shaped wrench.
BLACK BAG
STEP 1
STEP 2
STEP 3
Console Mast
Cover
Console Mast
Water Bottle
Cage
Console Mast
Bracket
STEP 4
Heart Rate
Wires
Handlebar
STEP 5
STEP 6