Vision SP-1200P User manual

1
SP-1200P_manual_en
SP-1200P POWERED SPEAKERS
OWNERS MANUAL
www.visionaudiovisual.com/techaudio/sp-1200p

2
SP-1200P_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products are certified and comply with all known local regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIGIN
All Vision products are made in the People’s Republic of China (PRC).

3
SP-1200P_manual_en
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to use your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could also be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is essential for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
WATTS
The most consistent standards for measuring watts are “Program Power” and “RMS” because
these measure average sustained levels.
Where loudspeakers have integrated amplifiers, then load (resistance, measured in ohms) is
known so the wattage rating is fixed.

4
SP-1200P_manual_en
FRONT PANELS
REMOTE CONTROL
1. Power
2. Input Select
3. Volume
4. Mute
5. Tone Control
NOTE: When power is turned on the last volume setting and input will resume.
Volume Dial
Long push to turn on/off
Short push to switch input
IR receiver
1
2
3
4
5
Active Loudspeaker
Slave Loudspeaker

5
SP-1200P_manual_en
INSTALLATION
1. FIT BRACKETS TO WALL Position brackets over load-bearing studs and use appropriate
screws to fix brackets. Ensure they are plumb.
NOTE: Do not position the top of bracket closer than 90mm to ceiling.
2. TERMINATE CABLES TO MOUNTS
Slave loudspeaker bracket:
Master loudspeaker bracket:
Incorrect termination of power is dangerous and will damage the product.
The black cable is negative (-). The white cable is positive (+).
Input from master loudspeaker
Use unshielded speaker cable provided. If cable
provided is not long enough use unshielded
speaker cable with gauge of 0.75mm or higher.
Blue= Input 1 (phono or minijack cable)
Green= Input 2 (phono or minijack cable)
Black= Loudspeaker output to slave speaker
(unshielded cable)
Red= Power Input

6
SP-1200P_manual_en
3. FIT LOUDSPEAKERS TO MOUNTS Fit loudspeakers to brackets from above. They click into
place and cannot be removed.
OPERATION
1. TURN ON AND OFF Long press on volume dial
2. CHANGE INPUT Short press on volume dial
90mm

7
SP-1200P_manual_en
TO REMOVE LOUDSPEAKER
1. Squeeze the two tabs together at top/rear of loudspeakers.
2. Lift loudspeaker up and off.

8
SP-1200P_manual_en
TROUBLESHOOTING
If your system is not operating properly, please refer to the following information. If the
problem persists, disconnect from power and contact your AV reseller immediately.
Problem
Correction
No power light
Rotate volume control clock-wise.
Check power source and power input cable.
Check fuse in power cable plug.
Power light on but no
sound
Turn the volume dial on the master loudspeaker up.
Make sure the output volume on your test device is at full and
that it works through the built-in device loudspeakers.
Hum or noise
Check that all input cables shielded properly. Poor quality
cable has uneven shielding which introduces noise.
Make sure all source devices are connected to the same power
source. If disconnecting a laptop from power solves the
problem then this is definitely the cause of the problem.
Passive loudspeaker not
working or quieter
Check speaker cable to ensure there a proper connection at
both ends.
Passive loudspeaker is
quieter than master
loudspeaker
This is typically caused by the use of incorrect cable between
the master and passive Loudspeakers. It is too thin, or
shielded. Replace immediately.

9
SP-1200P_manual_en
SPECIFICATIONS
PRODUCT DIMENSIONS: 150 x 145 x 220 mm (length x width x height for each speaker)
PRODUCT WEIGHT: 3.8 kg (per pair)
CONSTRUCTION MATERIAL: MDF
COLOUR: White
TECHNICAL DETAILS:
Amplifier Output: 2 x 15w watts (RMS)
Woofer: 4″
Tweeter: 1.5″ Silk
Input / Output Terminals: Phoenix connectors
Output Impedance: 4 ohms
Sensitivity: 85dB (1w/1m)
Frequency response: 80Hz-16kHz
POWER SUPPLY: 100/240v 50/60Hz AC External Power Supply – integrated transformer/plug
type. DC Output 5V 2A, DC Cable 1.8m.
Interchangeable prongs including UK, EU, AU, US. Note: a normal figure-8 cable can be plugged
into the transformer if preferred.
COMPLIANCE RoHS, WEEE, and CB Compliant
ACCESSORIES:
2 x Wall brackets
1 x 5m Speaker Cable
Frequency Response Graph: (dBSPL vs Frequency)

10
SP-1200P_manual_en
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoidance of
doubt, this will be taken from the information held by the appointed national distributor at the
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to
notify the national distributor via your AV reseller. The liability of the manufacturer and its
appointed service company is limited to the cost of repair and/or replacement of the faulty unit
under warranty, except for death or injury (EU85/374/EEC). This warranty protects you against
the following:
• Failure of any components, including the power supply.
• Damage when the product is first removed from its packaging if reported within 24 hours of
purchase.
If you find you do have a problem with this product, you should contact the AV reseller you
purchased this product from. The original purchaser is responsible for shipment of the product
to the manufacturer’s appointed service centre for repair.
We will endeavour to return repaired units within 5 working days, however this may not always
be possible, in which case it will be returned as soon as practicably possible. In line with our
WEEE commitments, the manufacturer endeavours to replace the faulty parts of the product
rather than replacing the whole unit. This warranty does not protect this product against faults
caused by abuse, misuse, incorrect installation, unstable or faulty power input, which might be
caused by ignoring the guidelines set out in this manual.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time and without notice. Such changes will be incorporated into new editions of the User
Manual.