VisionAIR 1VAHQ18WG User manual
MODEL 1VAHQ18WG
OWNER’S MANUAL
DIGITAL 6 TUBE INFRARED HEATER
18"
2
SAFETY & PRECAUTIONS
CONTINUEDCONTINUED
IMPORTANT NOTE:
Read the manual carefully. Make sure to save this manual for
future reference. Illustrations in this manual are for explanatory
CONTENTS
CONTENTS
SAFETY INFORMATION ........................................................................................... 3
IN THE BOX................................................................................................................... 6
PRODUCT DIAGRAM................................................................................................. 6
OPERATING INSTRUCTIONS ................................................................................. 9
MAINTENANCE .........................................................................................................11
STORAGE ....................................................................................................................11
TROUBLESHOOTING..............................................................................................11
TECHNICAL DATA
Model: 1VAHQ18WG
Voltage: 120V / 60Hz
Watts: 1500W
3
SAFETY INFORMATION
Thank you for choosing a VisionAir Infrared Zone Heating System. This owner’s
manual will provide you with valuable information necessary for the proper
care and maintenance of your new product. Please take a few moments to
thoroughly read the instructions and familiarize yourself with all the operational
aspects of your new heater.
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to
1. Read ALL instructions before using this unit.
2.
yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin
touch hot surfaces. If provided, use handles when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper,
clothes, and curtains at least 3 ft from the front of the heater and keep them
the heater.
5. Extreme caution is necessary when any heater is used by or near children or
the disabled, or when the heater is left operating and unattended.
6. DO NOT operate any heater with a damaged cord or after the heater
malfunctions, has been dropped or damaged in any manner. Return heater
to authorized service facility for examination, electrical or mechanical
7. This heater is not intended for use in bathrooms, laundry areas and similar
indoor locations. NEVER locate heater where it may fall into a bathtub or
other water container. To protect against electrical hazards, DO NOT immerse
in water or other liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs,
will not be tripped over.
10.
4
SAFETY & PRECAUTIONS
CONTINUEDCONTINUED
SAFETY INFORMATION
11.
manner. DO NOT use on soft surfaces, like a bed, where openings may
become blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas
13. Always plug heaters directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
14.
outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull
16. Always unplug the unit before moving or cleaning, or whenever the heater is
not in use.
17. Use only for intended household use as described in this manual. Any other
unauthorized dealers may cause hazards.
18.
19. DO NOT use outdoors.
20.
with any solid-state speed control device.
21.
on this unit. Doing so will void your warranty. The inside of the unit contains
only.
22. Connect to properly grounded outlets only.
23. Save these instructions.
WARNING Read and understand this entire owner’s manual, including
all safety information, before plugging in or using this product. Failure to do so
(Continued)
5
SAFETY INFORMATION (Continued)
TIP-OVER SAFETY FEATURE
restored to an upright position, the heater will reset.
OVERHEAT SAFETY FEATURE
This heater is equipped with an overheat safety feature. When the heater’s
internal components reach a certain temperature that could cause overheating
WARNING
It is normal for the power cord to feel warm to the touch; however, a loose
electrician to inspect the original outlet for damage.
6
SAFETY & PRECAUTIONS
CONTINUEDCONTINUED
• INFRARED ZONE HEATING SYSTEM
• REMOTE CONTROL
• REMOTE CONTROL BATTERY
• INSTRUCTION BOOKLET
IN THE BOX
PRODUCT DIAGRAM
Control Panel
Temp Sensor
Air Intake
Remote
Air Outlet
7
PRODUCT DIAGRAM
CONTROL PANEL
1.
2.
3.
4.
value for the timer.
5.
6.
7.
set mode, or display lock.
8.
(Continued)
1 2 3 4 6
8
7
5
8
SAFETY & PRECAUTIONS
CONTINUEDCONTINUED
PRODUCT DIAGRAM
REMOTE
PREPARATION
power outlet and turn on the power switch in the rear of the unit. Only operate
heater in upright position.
(Continued)
PULL
Remote Battery cover
Model: CR2025 | Voltage: DC 3V 0.1W | Capacity: 150mAh
This remote control uses one CR2025 battery (included)
WARNING
precaution may result in an explosion. Dispose of batteries at your local
hazardous material processing center or per local law.
9
OPERATING INSTRUCTIONS
1. Start and select working mode
2. Setting Desired Temperature
3. Setting the POWER OFF TIMER Function
Turn the heater on by pressing the ON/OFF button on the control panel or
by pressing the Power button on the supplied remote control.
Once power is o, heating element will stop working at rst. Fan will
prolong working for 3 min to emit plenty of heat inside. This mark will
indicate running during the 3 min.
Select a heat Mode
Press the HEAT button to toggle between high and low heat modes.
Press ECO button for ECO mode selection.
High Mode uses 1500W;Middle Mode uses1000W Low Mode uses 500W.
ECO mode is an Economic Energy Saving Function. When ECO mode is
chosen, the heater will manage itself from less to more heating power
(watts) in an attempt to maintain a constant warm 68°F.
Or Adjust the desired temperature by pressing the Up/Down arrows on the
control panel or remote control.
Desired temperature options vary from 59°F to 86°F. Once you have
chosen the desired temperature, the heater will remain on until the room
temperature increases to the temperature on the digital display. The heater
will cycle on and o to maintain the desired room temperature.
Turn the heater to the “On” position. Press the Timer button on the heater’s
control panel or the remote.
The digital display changes from the “temperature” to the “hours” option for
the timer. Continue to press the timer button to change the number of hours
you would like the heater to run before powering itself o. The hour options
for the timer are from 0 to 12 hrs. (in 1 hr increments).
The selected hour increments will ash for a few seconds, then revert back
to the set desired temperature. The Timer indicator light will remain lit as
long as the Timer is set. The heater will power OFF when the internal heater
clock counts down the hour increments you set.
NOTE:
OFF after a certain set time, and can only be set while the heater’s display
is in the “On” position.
10
SAFETY & PRECAUTIONS
CONTINUEDCONTINUED
4. Setting the POWER-ON-TIMER Function
5. Setting electro lock
The Electro Lock can help avoid the heater from being accidentally engaged by
children. The locking mechanism can be set in both the ON and OFF modes.
Turn the heater to the “OFF” position .Press the Timer button on the heater’s
control panel or the remote.
The digital display shows the “hours” option for the timer. Continue to press
the timer button to change the number of hours you would like the heater’s
internal clock to count down before powering itself on. The hour options for
the timer are from 0 to 12 hrs. (in 1 hr increments).
The heater will power itself ON when the internal heater clock counts down
the hour increments you set.
And
Press Temp Up and Temp Down buttons at the same time for 3 seconds.
Locking is complete when you hear a beep. When locked, the functions of
the control panel and remote will be locked for use.
And
When you need to unlock it, press Temp Up and Temp Down buttons at the
same time for 3 seconds. You will hear a beep. The control panel and remote
control will become functional again.
NOTE: The Power-ON-Timer Function will allow for the heater to power
ON after a certain set time, and can only be set while the heater’s display is
OPERATING INSTRUCTIONS (Continued)
11
TROUBLESHOOTING
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check to see if the battery on the remote is placed correctly, undamaged.
MAINTENANCE
1.
2. Unplug the unit and let it cool completely.
3. To keep the heater clean, the outer shell may be cleaned with a soft, damp
cloth. You may use a mild detergent if necessary. After cleaning, dry the
unit with a soft cloth.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough
brushes to clean the heater. This may cause damage or deterioration to the
surface of the heater.
5. DO NOT immerse the heater in water.
6. Wait until the unit is completely dry before use.
7. If won’t use the unit for a long time, please take out battery in remote
control according to following steps, then take care of the remote control.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt
build-up, use the original packaging to repack the unit.
PULL
PUSH
Remote BatteryBattery cover
833-950-1185 |support@visionairproducts.com
www.visionairproducts.com
4560 W. 160th Street
Cleveland, OH 44135
Printed in China |0423_M029
CONSUMER PRODUCT INFORMATION
For your own records, please attach a copy of your sales receipt to this manual.
Also, write the store name/location and date purchased below:
Store Name: ___________________________________________________________
Location:______________________________________________________________
Date Purchased: _______________________________________________________
Table of contents
Other VisionAIR Heater manuals
VisionAIR
VisionAIR 1VAHBB27 User manual
VisionAIR
VisionAIR 1VAHCF18 User manual
VisionAIR
VisionAIR 1VAHL24D User manual
VisionAIR
VisionAIR 1VAHCT23 User manual
VisionAIR
VisionAIR 1VAHL22M User manual
VisionAIR
VisionAIR 1VAHG5000 User manual
VisionAIR
VisionAIR 1VAHCU10 User manual
VisionAIR
VisionAIR 1VAHQ23 User manual
VisionAIR
VisionAIR 1VAHW09 User manual
VisionAIR
VisionAIR 1VAHG7500 User manual
Popular Heater manuals by other brands
Olimpia splendid
Olimpia splendid CALDO TRENDY Instructions for use and maintenance
Sundirect
Sundirect PE380-Plus Installation & operation instructions
Berner
Berner B-22 Installation and maintenance instructions
Toolland
Toolland TC78022 manual
Winco
Winco ESH-1 Operating instructions manual
Marley
Marley ST02125 Installation, operation & maintenance instructions
STIEBEL ELTRON
STIEBEL ELTRON CON 100-1 Premium Operation and installation
Climate King
Climate King HCK-TP30 User's manual and operating instructions
Sovelor
Sovelor MAGNUM 140 User and Maintenance Book
Haverland
Haverland RCTT Instruction guide
SVB
SVB Kerosene Heater operating instructions
Fondital
Fondital DECUS Installation and Maintenance
hydro THERMAL
hydro THERMAL K500 Installation, operation & maintenance manual
Nortek
Nortek C8QA Series installation instructions
Webasto
Webasto Air Top 2000 S D Service and repair manual
CANVAC
CANVAC COE3200V user manual
BN Thermic
BN Thermic SCHG-30T Instructions for use
Frico
Frico AGS5500 Original instructions