Visionhitech VC58EHi Manual

Page 1/ 16
HARDWARE INSTALLATION GUIDE
VC58EHi –Standard D1 Box Type IP Camera
VC58SMi –1.3 Megapixel Box Type IP Camera
VC58SM3Ti –3.0 Megapixel Box Type IP Camera
Version 1. 0. 2
Released on 1st of Sept., 2011
Vision Hitech Co., Ltd.

Page 2/ 16
PRECAUTIONS
By selecting this product, you have decided to use a professional device that guarantees highest quality and
reliability. We would like to thank you very much for your confidence and kindly ask you to read the following
instructions carefully before installation and operation in order to take full advantage of all quality features
regarding this product.
The lighting flash with an arrowhead symbol, within an equilateral triangle is intended to alert
the user to the presence of non-insulated dangerous voltage within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at its own
expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
-Do NOT use power source other than that specified.
-Do NOT expose this appliance to rain or moisture.
Trademarks
All names used in this manual for hardware and software are probably registered trademarks of respective
companies.
This installation should be made by a qualified service person and should conform to all local codes.

Page 3/ 16
Table of content
Hardware Installation Guide
1. Precautions ---------------------------------------------------------------------------------------------------- 4
2. Limitation of liability ---------------------------------------------------------------------------------------- 4
3. Disclaimer of warranty ------------------------------------------------------------------------------------- 4
4. Package Contents --------------------------------------------------------------------------------------------- 5
5. Name and function of each part ------------------------------------------------------------------------- 6
6. Installation ---------------------------------------------------------------------------------------------- 8
7. Dimension (mm) ----------------------------------------------------------------------------------------------- 10
8. Specification ----------------------------------------------------------------------------------------------------- 11
VC58SMi ------------------------------------------------------------------------------------------------------------------- 11
VC58SM3Ti -----------------------------------------------------------------------------------------------------------------13
VC58EHi ------------------------------------------------------------------------------------------------------------------- 14

Page 4/ 16
1. Precautions
Please read the manual carefully before the installation in order to set up the camera correctly and to
obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should be only carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply
and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera. To avoid electric shock, never remove
the screws or covers. There are no parts inside that need maintenance by the user. All maintenance should
be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time. Be
careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area. CCD may go defective at this
condition.
Please give a special attention to keep the unit from dangerous drop or external shock during the process
of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CCD.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right. This publication could include technical inaccuracies or typographical errors. Changes
are added to the information herein, at any time, for the improvements of this publication and/or the
corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below:
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or exemplary,
arising out of or relating to the product;

Page 5/ 16
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user;
(3) Unauthorized disassemble, repair or modification of the product by the user;
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause including any
failure or problem of the product;
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system combined by the
devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject, due to
violation of privacy with the result of that surveillance-camera's picture, including saved data, for some
reason, becomes public or is used for the purpose other than surveillance.
4. Package Contents
Hardware Installation Guide
IP Camera
C-Mount Adaptor
Auto Iris Lens Plug
Power Adaptor (Option)
CD
-Hardware Installation Guide (PDF)
-IP Camera Manual (PDF)
-NVR Pro Manual
-NVR Lite (16Ch) Program
-IPScan Utility Program (IP Installer)

Page 6/ 16
5. Name and function of each part
5-1. Front
5-2. Right side
- Back focus adjustment Knob: Fine tuning of the Back Focal Length
Protective cover
C-Mount lens adaptor
Fixture
Auto IRIS Lens Connector
Back focus adjustment Knob
(Tolerance + / - 0.5mm)
Day/Night mechanical
filter changer
(Inside)
Intelligent
Photo sensor
1/3”Sony super HAD
CCDII & WDR chipset

Page 7/ 16
5-3. Bottom
5-4. Rear side
■VC58EHi,VC58SMi
Fixture
1/4”-20 mounting thread
Fixture can be separated and attached on the top side as well.
Please use the supplied clamp screws only to change the position of the bracket.
Using screws more than 5mm depth can do a serious damage to the inside of this camera.
* Use an international standard 1/4”-20 mounting screw to install the camera.
SD Card Insert Hole
Sensor/Alarm Connector
Status LED (Yellow)
Power LED (Green)
Network Connector
Analog Video Out
Power Connector
Microphone-in(Audio-in)
Speaker-out (Audio-out)
Reset button

Page 8/ 16
■VC58SM3Ti
Power Connector: Only use the supplied AC adapter to avoid any possible damage from electric shock.
Network Connector: Connect 10Base-T Ethernet or 100Base-TX Fast Ethernet cable. When use PoE, connect
Ethernet cable coming from PoE injector or switch.
Sensor/Alarm Connector: To connect external devices such as infrared sensors, alarms or motion detectors.
Audio-out: Use to connect to an external speaker for audio communication. The audio sent over the network
from a connected client computer can be delivered through this externally connected speaker.
Audio-in: The external microphone for audio input. The live audio can be captured and transmitted to the
connected camera client via the use of this MIC.
RESET: Restore the factory default settings.
Power LED (Green): Once power is supplied to the camera, the green LED will light.
Operating Status LED/Network Activity LED (Yellow): This LED indicates the camera’s operating status. Once
power is supplied and the camera is connected to network, the LED lights and then blinks very fast as long as
the video is transmitted on the network during normal operation. When there is no video transmission, the
LED stops blinking.
SD Card Insert Hole : Insert SD Card for local storage
Analog Video Out : Utilizes analog video by connecting to DVR or monitor, or can be connected to video tester
when installing camera.
SD Card Insert Hole
Status LED (Yellow)
Power LED (Green)
Network Connector
Analog Video Out
Power Connector
Microphone-in(Audio-in)
Speaker-out (Audio-out)
Reset button
Sensor/Alarm Connector
RS485 Connector

Page 9/ 16
6. Installation
6-1. Lens
Lens is not supplied with the unit. C-Mount or CS-Mount type of lens is useable.
Please select a lens that has a good F-Stop number in order to get the best picture quality. Use of DC auto iris
lens is recommended to achieve the best results for operating this product effectively.
☞Caution
Please make sure the surface of the lens is always clear. Clean dirt or water drops with soft cloth in order to
avoid the picture blooming or reflection.
6-2. When using an auto iris lens (DC-drive)
1. Please take off the sleeve outer cable of the lens by 10mm
2. Please take off the sleeve inner cable of the lens by 2mm.
3. Solder the wires on the pin-connector (iris-jack) supplied with the lens according to the pin configuration as
shown in the drawing.
4. Assemble the lens.
5. Connect the Auto Iris jack.
6. Adjust the DIP S/W to DC according to the type of lens.
6-3. When using a C-mount Lens
●Please assemble C-Mount adaptor.
●C-Mount adaptor is included in the package.
●Fix the lens by turning it clockwise.
6-4. When using a CS-mount Lens
Pin No.
Lens
DC
No.1 Pin
Damping -
No.1 Pin
Damping +
No.1 Pin
Drive +
No.1 Pin
Drive -

Page 10 / 16
●Take off the Protection cover.
●Assemble the CS-MOUNT lens by turning it clockwise.
- When used with an Auto Iris lens, please insert
the iris jack into the Iris socket which is located
on the right side of the camera.
- Please set the lens selection to DC on the OSD setting.
Caution
- Use the lens as shown in the picture here.
- When the lens is out of the spec, it could damage the camera inside or
may not be correctly fitted with the camera.
- Use the lens less than 450g. Heavier lens can damage the camera.
6-5. Video Monitor
Connect Video cable with BNC-male connector to the monitor
6-6. 12V DC Power
This IP camera uses 12VDC or IEEE802.3af PoE for power source. Please make sure to use a UL/CE approved
and 12VDC/500mA regulated power supply or standard PoE injector, mid- or end-span for input power.
PoE (Power over Ethernet) Support
Power over Ethernet, or PoE, technology describes a system to transmit electrical power, along with data, to
remote devices over standard twisted-pair cable in an Ethernet network. This technology is useful for
powering IP telephones, wireless LAN access points, network cameras, remote network switches, embedded
computers, and other appliances where it would be inconvenient and expensive. (Main wiring must be done
by qualified and/or licensed person.)

Page 11 / 16
The standard IEEE 802.3af describes two types of devices: Power Sourcing Equipment (PSE)and Powered
Devices (PD). Power sourcing equipment provides power to the powered devices. The network camera
represents the powered device, whereas a PoE Injector is a PSE device. The VISION Network Camera models
are IEEE 802.3af standard PoE compliant. They can be used with any IEEE 802.3af-compliant PoE injector, PoE
switch, PoE mid-span and PoE end-span.
Various types of PoE equipments
7. Dimension (mm)
8. Specification
8-1. VC58SMi : 1.3 Mega Pixel HD IP Camera
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
32 Mbyte Flash Memory
SDRAM
256Mbyte
Image Pickup
Image sensor
1.3 Megapixel 1/3" SONY progressive scan CMOS image sensor
Total Pixels
1384(H) x 1076(V) 1.49 Megapixel
Effective Pixels
1329(H) x 1049(V) 1.39 Megapixel
S/N Ratio
More than 50dB
Power over Ethernet (PoE) Injector
PoE Mid-span
PoE Office Switch

Page 12 / 16
Min. Illumination
0.5 Lux with DSSX2 (F1.2, 30IRE, AGC On),
Day & Night
D/N Output Port, ICR
Lens (Not included)
C/CS Mount, DC Iris
Video
Video compression
H.264 baseline profile, Motion JPEG
Resolutions
Up to 1280 x 720
Frame rate
H.264 Up to 30fps with 1280x720
MJPEG Up to 30fps with VGA resolution
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming
Two-way, full duplex
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Single Mono)
Audio output
Line output/ 1 x Line-Out (Single Mono)
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
Wireless LAN
IEEE 802.11 b/g/n (for VC58SMi-W)
System
integration
Intelligent video
Motion detection up to 1280x720 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
External output activation/Normal Open/Close Type
Video buffer
16MB pre-alarm and post-alarm
Recording
Save to SD/SDHC card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
RESET Button
1 x Factory Reset Button
Power Source
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af
Power Consumption
Max. 5.5W
Net Weight
580g (Camera Only, without Lens)
LED's
Power, Network Connection

Page 13 / 16
Dimension
66mm(W) X 57mm(H) X 126mm(D)
Environment
Operating Temperature
-25 degree~50 degree Celsius (-13F~122F)
Storage Temperature
-25 degree~60 degree Celsius (-13F~140F)
Software
Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor, Bracket,
Software CD
8-2. VC58SM3Ti : 3 Megapixel Full HD IP Camera
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
16 Mbyte Flash Memory
SDRAM
256Mbyte
Image Pickup
Image sensor
3.0 Megapixel 1/2.8" SONY progressive scan CMOS image sensor
Total Pixels
2144(H) x 1588(V) 3.4 Megapixel
Effective Pixels
2096(H) x 1561(V) 3.27 Megapixel
S/N Ratio
More than 52dB
Min. Illumination
1 Lux with DSSX2 (F1.2, 30IRE, AGC On),
Day & Night
D/N Output Port, ICR
Lens (Not included)
C/CS Mount, DC Iris
Video
Video compression
H.264 High profile, Motion JPEG
Resolutions
Up to 2048 x 1536
Frame rate
H.264 Up to 15fps with 2048x1536
MJPEG Up to 30fps with 1080p resolution
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Output
Up to 2048 x 1536
Audio
Audio streaming
Two-way, full duplex
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Single Mono)
Audio output
Line output/ 1 x Line-Out (Single Mono)
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP

Page 14 / 16
RTSP, RTP, TCP, UDP, ICMP, DHCP
Wireless LAN
IEEE 802.11 b/g/n (for VC58SM3i-U)
System
integration
Intelligent video
Motion detection up to 1920x1080 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
External output activation/Normal Open/Close Type
Video buffer
16MB pre-alarm and post-alarm
Recording
Save to SD/SDHC card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
RESET Button
1 x Factory Reset Button
Power Source
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af
Power Consumption
Max. 5.5W
Net Weight
580g (Camera Only, without Lens)
LED's
Power, Network Connection
Dimension
66mm(W) X 57mm(H) X 126mm(D)
Environment
Operating Temperature
-25 degree~50 degree Celsius (-13F~122F)
Storage Temperature
-25 degree~60 degree Celsius (-13F~140F)
Software
Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor, Bracket,
Software CD
8-3. VC58EHi : Standard D1 IP Camera
Classification
Specification
General
CPU
32-bit ARM9 RISC CPU up to 533MHz, 32KB I/D-Cache, MMU
Video Buffer
16Mbyte Video Frame Buffer
Flash
16 Mbyte Flash Memory
SDRAM
256Mbyte
Image Pickup
Image sensor
1/3" Sony 960H Ex-view HAD CCDⅡ
Effective Pixels
NTSC : 976(H) x 494(V), PAL : 976(H) x 582(V)
H. Resolution
650TV Lines(Color)/ 700TV Lines(B/W)
Synchronizing system
Internal
Scanning system
NTSC : 525 Lines PAL : 625 Lines 2:1 Interlaced
S/N Ratio
More than 52dB (AGC Off)
Min. Illumination
0.1 Lux (Color), 0.01Lux (B/W)
Shutter Speed
NTSC:1/60~1/100,000 sec. PAL:1/50~1/100,000 sec.
Gamma Correction
Standard γ = 0.45
Iris Control
DC/ Manual
Day & Night
D/N Output Port, ICR
Lens (Not included)
C/CS Mount, DC Iris
Video
Video compression
H.264 baseline profile, Motion JPEG
Resolutions
Up to D1(NTSC:720X480, PAL:720X576)
Frame rate
H.264 Up to 30fps at D1

Page 15 / 16
MJPEG Up to 30fps at D1
Video streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR/CBR in H.264
Pan/Tilt/Zoom
Digital PTZ
Image setting
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
Effect - Color, Sharpness, Mirror/V-Flip, etc.
Output
BNC x1, 1.0Vp-p, 75 ohm Composite Video, NTSC/PAL
Audio
Audio streaming
Two-way, full duplex
Audio compression
G.711
Sample Rate
8KHZ
Data Rate
64Kbps
Audio input
Microphone input /1 x Line-In (Single Mono)
Audio output
Line output/ 1 x Line-Out (Single Mono)
Network
Security
Password protection
User access log
HTTPS encryption
Supported protocol
HTTP, HTTPS, FTP, SMTP, UPnP, DNS, DynDNS, NTP
RTSP, RTP, TCP, UDP, ICMP, DHCP
Wireless LAN
IEEE 802.11 b/g/n (for VC58EHi-W)
System
integration
Intelligent video
Motion detection up to D1 with 32x24 blocks
Alarm trigger
Motion detection
External input/Normal Open/Close Type
Alarm events
File upload via ftp, e-mail
Notification via email, FTP and TCP
External output activation/Normal Open/Close Type
Video buffer
16MB pre-alarm and post-alarm
Recording
Save to SD/SDHC card with event mode and continuous mode
Firmware upgrade
Remote upgrade via network
API
CGI Interface document
ActiveX Interface(ocx(dll) + document)
Physical
RESET Button
1 x Factory Reset Button
Power Source
DC 12V/1.5A, PoE(Power over Ethernet): 802.3af
Power Consumption
Max. 5.5W
Net Weight
580g (Camera Only, without Lens)
LED's
Power, Network Connection
Dimension
66mm(W) X 57mm(H) X 126mm(D)
Environment
Operating Temperature
-25 degree~50 degree Celsius (-13F~122F)
Storage Temperature
-25 degree~60 degree Celsius (-13F~140F)
Software
Included Software
NVR Lite (16 Channel), IP Installer (Windows Only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor, Bracket,
Software CD
■Specifications are subject to change without prior notice to enhance performance and stability

Page 16 / 16