ViTiny UM06-CSZ064C User manual

UM06-CSZ064C
User’s Guide
Version 1.0A

1
Content
1. Product Introduction ...........................2
1.1 Packing Contents .........................2
1.2 IR remote controller ....................2
1.3 Microscope introduction: ............7
1.4 Microscope Focus ......................12
1.5 Microscope accessory................14
2. Printed Notice....................................15
2.1 Maintenance..............................15
2.2 Product Specification.................16
2.3 Safety Instructions .....................17

2
1. Product Introduction
1.1 Packing Contents
The box contains 1 microscope and 10 accessories. Each model comes with
different accessories.
1.2 IR remote controller
The Digi Microscope is controlled by the IR remote controller or application
program and contains 3 different modes: Common Use, PC Cam and HDMI. When
the far distance control mode is enabled, only the Power, PC Cam, and HDMI
buttons can be accessed through the remote controller.
1.2.1 Buttons for Common Use
The following buttons are used for both PC Cam and HDMI mode.
(1) Power ：Turn on/off.
(2) Motor Reset (Recalibrates entire operation)：Returns to the lens position.
If a loss of electricity occur during operation, please reset the operation.
(3) Manual focus: Press Zoom out till the end to set up the sensor motor at
the top, so that all optical objectives lens reach the parfocal distance.
Item
Q’ty
Item
Q’ty
UM06 Camera
1
White Balance Card
1
HDMI Cable
1
Calibrator
1
USB 2.0 Cable
1
User’s Guide
1
Power adaptor
1
Software CD
1
S110 Stand
1
CSZ064C Lens
1
Stand assemble guide
1
IR Remote Controller
1

3
(3-1) Zoom in ：Zooms in; speed increases when held.
(3-2) Zoom out ：Zooms out; speed increases when held.
Microscope remote controller
Buttons for common use

4
1.2.2 Buttons for PC CAM
The following buttons are used only for PC Cam mode.
(1) PC CAM ：When in PC CAM mode, the USB cable must connect to a PC and
microscope. Please disable software before switching to HDMI mode or
powering off.
Buttons for HDMI mode
Buttons for PC CAM mode

5
1.2.3 Buttons for HDMI
The following buttons are used only for HDMI mode.
(1) HDMI ：When in HDMI mode, the HDMI cable must connect with the screen
and microscope.
(2) Menu on Screen ：Open/close menu for setting.
(2-1) BRIGHTNESS：Adjusts the brightness of the entire image. [1~31]
(2-2) CONTRAST：Emphasizes the difference between bright and dark. [1~31]
(2-3) SATURATION：Adjusts the color level. [1~31]
(2-4) EXPOSURE VALUE：
[ON] Auto mode, use with the exposure value +/-. This mode will
automatically adjust the image brightness. For the best result, turn on
all LED lighting. For more on adjustment, please refer to Section
1.2.3-(7).
[OFF] Manual mode, use with the LED brightness +/- and the exposure
value +/-. This mode allows you to manually adjust the LED brightness
and exposure value. For more on adjustment, please refer to Section
1.2.1-(2) and Section 1.2.3-(7).

6
(2-5) SHARPNESS：
[ON] Sharpens the image.
[OFF] Smooth the image.
(2-6) STATUS BAR：Suggest to OFF the Status Bar in CSZ064 model.
[ON] Displays the status bar on the top of screen. For more on the
status bar, please refer to Section 1.2.3-(9).
[OFF] Hides the status bar.
(2-7) OBJECT LENS：No Function in CSZ064 model.
(2-8) LCD SIZE：No Function in CSZ064 model.
(2-9) FACTORY：
[NO] Stays on the current setting.
[YES] Returns all settings to factory settings.
(2-10)Vx.xx.xx：Firmware version.
(3) Up ：Choose the previous item
(4) Down ：Choose the next item
(5) Left ：Choose the next value
(6) Right ：Choose the last value
(7) Exposure Value: 13 levels of exposure value are selectable, from +0.2~-2.0.
(7-1) Increase ：Use to increase exposure when the image is too dark.
(7-2) Decrease ：Use to decrease exposure when the image is too bright.
(8) Video Ratio ：Press Video Ratio button to change 3 different image sizes.
(9) Status Bar : The default setting is “OFF”, if status bar shows on screen,
please turn to OFF manually.
(10) Auto White Balance Calibration : To calibrate the white balance, place the
white balance card (included in box) under the lens, focus until clear, and
choose On. Because the white balance is sometimes influenced by external

7
light sources, it is recommended to calibrate the white balance if the color
seems off or incorrect.
(11) Image Freeze : On/Off image freeze. Freezes the image; press the button
again to return to preview.
(12) Sharpness : On/Off sharpness mode. Please refer to Section 1.2.3-(2).
1.3 Microscope introduction:
1.3.1 IR Remote Area/Indicator
When both the HDMI and USB indicator lights are on, the microscope is in standby
mode.
Caution: Please remove the transparent protection sheet on the IR receiver area.

8
(1) IR remote control aiming area○
a: The indicator will blink whenever buttons
are pressed. The indicator will blink, if the indicator did not blink means the
signal was not delivered and please repress again.
(2) HDMI indicator○
b: When lit up, the device is in HDMI mode.
(3) USB indicator○
c: When lit up, the device is in USB mode. The light will flicker if
the microscope is not connected to a PC.
○
b
○
c
○
a

9
1.3.2 Power/USB/HDMI port
(1) Power○
d: Power supply is only compatible with the cord in the box.
(2) USB○
e: The USB cable is used to connect the microscope to a PC to access the
application program. When the device is in PC Cam mode, connect the
microscope to a PC through the USB cable from the box. Make sure to connect
the USB cable first and then switch to PC Cam mode.
○
d
○
e

10
(3) HDMI○
f：The HDMI port is used to connect the microscope to a screen. When
the device is in HDMI mode, connect the microscope to the screen using the
HDMI cable from the box. * For TV screen connections, make sure to choose
the homologous image ratio and format.
1.3.3 CSZ064C Lens Assembling
Each CSZ064C lens has reach its parfocal distance when goods ship out; simply
screw ○
gthe CSZ064C lens under the UM06 camera and tighten up with stand○ h.
○
f
○
g

11
1.3.4 Illuminance
CSZ064C Lens has its own Coaxial illuminance, please insert the coaxial light
○
ito lens, then switch power ON ○ j.
○
h
○
i
○
j

12
1.4 Microscope Focus
Move the CSZ064C upward, leave 82mm to the object; press Zoom out
button to move the sensor to end position. Rotate the optical zoom from 0.6x-4x
see if all image is clear. If the lens does not reach parfocal distance, try turning
the gearbox to find clear image. If focus lost, please refer to the instruction to
tuning parfocal distance.
(2-1) In HDMI mode, press Zoom Out till the end.
(2-2) In PC CAM mode, press the Zoom Out till the end. (The sensor
position at around 18XX, each device has a little difference due to the
assembling tolerance.
When the image sensor position is fixed, as in (2-1) and (2-2), focus the image
by using knob ○
jto adjust the height and knob ○ kto fine tune.
○
l
○
k

13
1.4.1 Magnification chart
The below chart measured base on UM06-CSZ064C model on 24” screen with
working distance 82mm, and optical focusing from 0.6x-4x. The chart is only
a reference data, might not be accurate enough.
To use the measurement function in software, all the build in scales are not
correct. User’s must create and calibrate a new scale. Refer to the AP
User’s Guide in CD for more detailed information on create a new scale file.
CSZ064C Zoom lens working distance: 82mm (3.228”)
CSZ064C Lens magnification on 24” HDMI monitor. (Ref. Data)
Optical Adaptor(0.5x )
0.6x
1x
3x
3x
4x
1x Focusing lens
Working Distance(mm)
82
82
82
82
82
Mode 1, 2 FOV(mm)
11.7
7
3.5
2.35
1.8
Mode 3 FOV (mm)
8.7
5.2
2.65
1.8
1.35
Mode 1 Mag. (X)
34
56
110
164
215
Mode 2 Mag. (X)
44
74
147
220
288
Mode 3 Mag. (X)
59
99
197
290
380

14
1.5 Microscope accessory
1.5.1 Calibrator
Mainly used to calibrate the scale on the application program (please refer to the AP
manual for more information). The calibrator is transparent and can be applied onto
the object directly.
1.5.2 White balance card
The white side is used to calibrate the white balance. If the object is tiny, place it
onto the white balance card and move the card instead of the object.

15
2. Printed Notice
Please read the following information before operating.
2.1 Maintenance
Please abide by the following rules while storing or using this product:
2.1.1 Keep dry: do not place the product in a humid environment. Dry surroundings
help extend the life of the product.
2.1.2 Avoid temperature shock: temperature shock (for example, taking the product
into a warm room from a cold environment) will cause internal condensation
inside the machine. Please put the device inside the protection bag or
handbag to prevent temperature shock, and avoid using the device in an
environment with extreme temperatures.
2.1.3 Avoid dropping: the device may malfunction if it encounters strong collision,
vibration, or distortion.
2.1.4 Turn the microscope off before cutting off the power supply : do not forced
cut off the power supply.
2.1.5 Do not face the lens against strong light or sunshine for extended periods of
time: Strong light rays may degrade sensitive elements and generate white
stains on images.
2.1.6 Handle the device carefully: do not disassemble cables forcefully and avoid
contact with the lens since they are subjected to damage.
2.1.7 Make sure to switch the power supply off and unplug the power cable if the
device is not in operation for an extended period of time. Store the device in a
dry environment with excellent ventilation. Do not expose the machine in an
environment lower than -5ºC or higher than 50ºC.
2.1.8 While carrying, put the device inside the box to prevent it from being
damaged.

16
2.2 Product Specification
CMOS Sensor
5 million pixels CMOS sensor
Lens
CSZ064C Coaxial Zoom Lens
Magnification
Optical Zoom from 0.6x-4x.
Auxiliary source
Coaxial Light
DC port
Adaptor DC input
HDMI port
Output 1080P(1920*1080 Pixel) image
USB port
USB 2.0,3.0 compatible, connect with PC.
Focus control
IR remote controller/PC(application program) control
Power supplier
adaptor
(input：DC 5.0V/2.0A input：AC 100-240V 50/60Hz)
Power
Consumption (A/C)
0.225A (Max.)
Size
115x66x68mm
Weight
Host weight around 710 grams
Operation
environment
Temperature -5℃~ 50℃; Humidity-lower than 85%
(No Condensation)
For any changes, please visit http://www.vitiny.com

17
2.3 Safety Instructions
As an electronic product, please do not use the device in any place in which
electronic products are prohibited.
Keep the device away from water sources to avoid electric shock as it is not
waterproof.
Keep the device away from chemicals or substances with explosive or fire
hazards. Switch the device off near gas stations.
In the case that there are foreign substances or water inside the device, or the
device is dropped or damaged, please switch off and remove the power supply
to avoid fire and electric shock.
Do not look steadily into Light sources after switching on the host as it is
harmful to your eyes.
Please use only the product accessories provided in the box for connections.
Do not use any outside products without approval of original factory.
Please remove the power supply from the microscope when not in use.
Do not disassemble the machine for inspection. For any problems occurring in
the machine itself, please power off the device and contact us through e-mail:
[e-mail]

Please ask the distributor to fill in the name of the shop, address, purchase date, and
other contents to protect your rights and validate your one-year warranty since upon
the purchase date.
Contents of Warranty: The warranty is provided free of charge for faults caused by
manufacturing within one year from the purchase date.
Non-warranty:
1. Product appearance parts, such as the outer casing, knobs and LED cover, etc
(charged spare parts are limited to one year after completing the product
manufacturing).
2. Consumption goods of the host itself, such as LED lights and lens.
3. Product accessories and fittings, such as the power supplier, USB cable, HDMI
cable, calibrator, white balance card, remote controller…etc.
Services caused by any of the following situations in the period of the warranty shall
not be provided free of charge:
1. Improper use or disassembly, repair or refitting.
2. Any damages to the device caused by external or environmental factors.
3. Discrepancy of product serial number, unfilled or unidentified warranty. Any
inspection or repair service after the period of warranty will be charged as
follows:
(1) Service fees (including transportation fees) of product inspection.
(2) Repair fees.
(3) Fees of replaced parts
ViTiny Service Center Tel: [phone] Fax: [phone]
Address: 10 F., No.1, Section 1, Syuecheng Road, Dashu District, Kaohsiung City 840,
Taiwan (R.O.C.)
Website: http://www.vitiny.com