Vivo DESK-V201G User manual

Gray Kids' Height Adjustable Desk and Chair
Instruction Manual
SKU: DESK-V201G
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v201g
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
WARNING!
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF DESK OR CHAIR
• USE TIPOVER RESTRAINT OR ANCHOR DESK TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
PACKAGE CONTENTS
B1 (x1)
Chair Leg
B2 (x2)
Chair Feet
B4 (x1)
Side Support Bar
B5 (x1)
Center Support
Bar
B6 (x1)
Seat Bottom
B3 (x1)
Support Bar
B8 (x1)
Desktop
B9 (x1)
Right Side
Drawer Slider
B10 (x1)
Le Side
Drawer Slider
B11 (x1)
Plastic Drawer
B12(x1)
Desk Leg
B13(x2)
Desk Feet
B7 (x1)
Seat Back
A1 (x8)
Metal Washer
A3(x12)
Plastic Washer
A4 (x4)
Long Plastic Thread
Screw
A5 (x2)
Knob
A2 (x12)
Medium Screw
A6 (x4)
Short Screw
A8 (x4)
Long Screw
A9 (x1)
Hook
A10 (x1)
Allen Wrench
A7 (x4)
Short Plastic
Thread Screw
NOTE: Not all hardware included will be used.

3
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Place chair legs (B1) into chair feet (B2), making
sure legs are fully seated in openings.
Phillips
Screwdriver
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
STEP 2
Secure feet using x4 medium screws (A2) and x4
metal lock washers (A1). Tighten with the Allen
wrench (A10).
STEP 3
Assemble right side support bar (B3) to leg using
x2 medium screws (A2) and x2 plastic washers
(A3). The support bar has a large hole on the
le side which will face inward. Tighten with the
Allen wrench (A10).
STEP 4
Slide center support bar (B5) into the large
hole in right side bar. Slide le side support bar
(B4) onto center bar, and secure to legs with x2
medium screws (A2) and x2 plastic washers (A3).
Tighten with the Allen wrench (A10).
165.3lbs
(75kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 220.5lbs
(100kg)
DESK CHAIR

4
STEP 5
Mount plastic seat bottom (B6) to
assembled chair frame using x4 long
plastic thread screws (A4). Tighten with a
Phillips screwdriver.
STEP 6
Slide plastic seat back (B7) onto chair frame,
aligning upper or lower holes in seat back with
screw holes in frame depending on the needed
height.
STEP 7
Secure seat back using knobs (A5).
STEP 8
Adjust chair feet to sit level if needed.
STEP 9
Assemble right side drawer slider (B9) to desktop (B8) using x2
short screws (A6) and x2 plastic washers (A3). Tighten with the Allen
wrench (A10). Ensure slider pulls out towards the front of the desk.

5
STEP 10
Assemble le side drawer slider (B10) to desktop
using x2 short screws (A6) and x2 plastic washers
(A3). Tighten with the Allen wrench (A10).
STEP 11
Mount plastic drawer (B11) to sliders using x4 short plastic thread screws (A7).
Tighten with screwdriver.
STEP 12
Place desk legs (B12) in desk feet (B13), making
sure legs are fully seated in openings.
STEP 13
Secure feet using x4 medium screws (A2) and x4
metal lock washers (A1). Tighten with the Allen
wrench (A10).

6
STEP 14
Assemble desktop to legs using x4 long screws (A8) and x4
plastic washers (A3). Tighten with the Allen wrench (A10).
STEP 15
Squeeze sides of hook (A9) and fit into slot on le or right
side of desk.
STEP 16
Adjust desk feet to sit level if needed.
STEP 17
Loosen knobs on sides of desk to adjust desk tilt angle, and
tighten knobs to secure position.

7
Height Adjustment
RAISE DESK: Step on the support bar with one foot and pull up with even motion on both sides of the
desk, until it reaches desired height.
LOWER DESK: Step on the support bar with one foot and pull up with even motion on both sides of the
desk, until it reaches max height. Slowly lower down to desired height.
RAISE/LOWER CHAIR: Remove both screws with washers from side of each leg using the Allen wrench.
Raise or lower the chair evenly until it reaches desired height, then reinsert screws with washers.
To avoid injury due to
falling, do not lean the
chair backwards or to
the sides while sitting.
Remove large or unstable
objects before tilting the
desktop.
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.

LAST UPDATED: 03/04/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303