Vivo DESK-V123EB User manual

Black Electric Multi Motor Corner Desk Frame
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v123eb
SKU: DESK-V123EB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual
and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x1)
Allen Wrench
(4mm and 5mm)
B (x14)
M6x12
C(x20)
M6x12 Flat Head
D(x2)
M8x12
E(x30)
M5x16
G(x8)
Cable Clip
H (x6)
Foot Pad
1 (x3)
Side Bracket
2(x3)
Motorized Leg
3(x3)
Feet
4(x3)
Inner
Crossbar
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
5 (x2)
Outer Crossbar
6 (x1)
Center Crossbar
7(x1)
Outer Extension
Crossbar
8(x1)
Inner Extension
Crossbar
9 (x1)
Extension
Connector
10 (x1)
Power Cord
11 (x1)
Control Unit
12 (x1)
Controller
13 (x3)
Extension
Cable
14 (x2)
Connecting
Plate
NOTE: x2 extras of each screw size have been
included, desktop not included
( 2-section corner desktop shown only for reference)
F(x12)
M6x35
I (x18)
Anti-Vibration
Pad

3
264lbs
(120kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Drill
Assemble an outer crossbar (5) and inner
crossbar (4) to x2 of the motorized legs (2) using
x2 M6x12 flat head bolts (C) for each crossbar.
Tighten with the 4mm Allen wrench (A). With all
legs upside down and side brackets (1) facing
away, the outer crossbars will be on the le, and
the inner crossbars on the right.
STEP 2
Mount the center crossbar (6) and an inner
crossbar (4) to the third motorized leg (2) using
x2 M6x12 flat head bolts (C) for each crossbar,
and tighten with the 4mm Allen wrench (A).
C
S=4mm
S=4mm
C

4
D
S=5mm
STEP 3
STEP 4
Attach a side bracket (1) to each motorized leg (2) using x2 M6x12 flat head bolts (C) for each. Tighten
with the 4mm Allen wrench (A). Mount the feet (3) to the motorized legs (2) using x4 M6x35 bolts (F)
for each and tighten with the 5mm Allen wrench (A). Screw the foot pads (H) into the feet.
Slide the crossbars of the le and corner leg together and flip the assembly right side up. Mount the
extension connector (9) to the center crossbar using M8x12 bolts (D) and tighten with the 5mm Allen
wrench (A), making sure the opening is facing up.
S=4mm
C
F
S=5mm
H
4

5
STEP 5
Slide the outer extension crossbar (7) and inner extension crossbar (8) onto the crossbars of the third
leg, then assemble to the extension connector (9) using x2 M6x12 bolts (B) for each crossbar and tight-
en with the 4mm Allen wrench (A). Adjust the frame size to fit the desktop, and tighten x8 M6x12 bolts
(B) into the underside of the outer crossbars using the 4mm Allen wrench to secure. We recommend
that each side of the desktop overhang the frame by no more than 10”.
S=4mm
B
STEP 6
Insert the anti-vibration pads (I) into the desktop mounting holes in the side brackets and crossbars.
I
5

6
STEP 7
Place the desktop on the assembled frame. Drill 10mm deep pilot holes using a 1/8” (3mm) drill bit, and
secure using x16 M5x16 screws (E). If using a 2-section desktop, secure sections using the connecting
plates (14) with x8 M5x16 screws (E). Tighten all screws with a Phillips screwdriver.
Mark screw locations for the control unit (11) and controller (12), making sure the controller cable is
able to reach the control unit, then drill 10mm deep pilot holes using a 1/8” (3mm) drill bit. Mount the
control unit and controller using x4 M5x16 screws (E). Tighten all screws with a Phillips screwdriver.
Connect the controller and legs (2) to the control unit. If needed, use the extension cables (13) to
connect the legs. Connect the power cord (10) to the control unit and plug into an AC power outlet.
Adjust foot pads (H) to sit level if necessary. Refer to Controller User Guide for operational instructions.
E
(X2)
3
14 8
AC
HSM1 M2 M3
G

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk
weight limit.
Keep area of vertical
motion free of
obstacles.
Keep weight on desk
balanced for correct
operation and longer
life of components.
Leave enough slack in
cables to allow for full
range of vertical motion.

LAST UPDATED: 01/09/2021
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303