Vivo DESK-V101ED User manual

White 48" Electric Drafting Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-v101ed
SKU: DESK-V101ED
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual and do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or
inappropriate use.
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
PACKAGE CONTENTS
A (x1)
Desktop
B(x1)
Crossbar
C(x1)
Wrist Rest
S-A (x16)
M6x12mm
Bolts
S-B x4)
M6x6mm Bolt
S-C (x4)
M4x5mm Bolt
S-D (x4)
5/8" Screw
H(x1)
Liing
Column
D (x1)
Sync Rod
E (x2)
Foot
F (x1)
Control Unit
G (x1)
Liing
Column
S-E (x1)
Allen Key
S-F (x3)
Cable Clip
K(x1)
Adapter
I (x1)
Shelf
J (x2)
Hook
L(x1)
Control
Panel
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

3
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Phillips
Screwdriver
STEP 2
120lbs
(54.43kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Assemble liing columns (G, H) to the desktop (A)
using 8 M6x12mm bolts (S-A) and Allen key (S-E).
Leave the screws loose with 3mm of thread exposed.
NOTE: Insert all necessary screws into holes before
completely tightening.
Mount the crossbar (B) to the columns using M6x6mm bolts (S-B). Tighten all screws with the
Allen key (S-E).
S-B
B
A
GH
S-A

4
STEP 3
Assemble the feet (E) to the columns using 8
M6x12mm bolts (S-A) and tighten with the Allen key
(S-E). Make sure the longer ends of the feet (E) are
facing towards the front of the desk.
STEP 4
STEP 5
Loosen the knobs on each end of the sync rod (D). Slide the socket end onto the motor sha and
tighten the knob to secure. Extend the hex sha into the socket in the other leg and tighten the knob to
secure.
a
O
NP
Install hooks (J) to shelf (I) using M4x5mm bolts (S-C) and tighten with Phillips screwdriver.
ES-A

5
STEP 5 (continued)
STEP 6
Mount the shelf to the underside of the desktop using two 5/8" screws (S-D) with a Phillips screwdriver.
Rest control unit (F) on shelf. Connect cables for motor, power (K) and control panel (L).
Mount the control panel (L) to the desktop using two 5/8"screws (S-D) and tighten with a Phillips
screwdriver. Use cable clips (S-F) to organize cables.
S-F
S-D

6
STEP 6 (continued)
If needed, adjust foot pads to level desk on uneven floor. Li handle to raise or lower front desktop
surface.
Remove the backing from the wrist rest (C) and place near the front edge of the desktop.
Li handle to raise or lower front desktop surface.
C

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.

LAST UPDATED: 03/04/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303