Vivo DESK-V120EB User manual

Black Electric Dual Motor Desk Frame
Instruction Manual
SKU: DESK-V120EB
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v120eb
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
PACKAGE CONTENTS
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
A (x14)
M5x16
B x18)
M6x12
C(x8)
M6x16
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
D(x4)
Foot Pad
E(x1)
4mm Allen
Wrench
F(x5)
Cable Clip
Note: Some hardware included may not be used.
1 (x1)
Desktop
(Not Included)
2(x1)
Control Panel
3(x2)
Side Bracket
4 (x1)
Power Cord
5 (x2)
Extension
Cord
6 (x2)
Leg with Frame
8(x1)
Control
Unit
9(x2)
Crossbar
7(x2)
Foot

3
220lbs
(99.79kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen, but do not remove, screws in legs (6). Tilt legs up and into frames and secure each leg with
two M6x16 screws (C) using Allen wrench (E). Attach feet (7) to legs using four M6x12 screws (B) for
each, then tighten with Allen wrench. Remove protective film from foot pads (D) and install pads into
feet.
TOOLS NEEDED
Phillips
Screwdriver

4
STEP 2
STEP 3
Turn assembled legs with frames right side up, then slide the crossbars (9) into the frames. Attach the
side brackets (3) to the frames using four M6x16 screws (C) and tighten with the Allen wrench (E).
Adjust the width of the frame to fit your desktop. Tighten eight M6x12 screws (B) into the underside of
the frames (6) to secure the adjusted length.

5
STEP 4
Attach your desktop (1) to the assembled desk frame using eight M5x16 screws (A).

6
STEP 5
Remove the protective film from the control panel (2). Mount the control panel and control unit (8)
to the underside of the desktop using four M5x16 screws (A). Use the extension cords (5) to connect
the motors to the control unit, then connect the control panel and power cord (4). Attach cable clip (F)
where desired.
STEP 6
Plug the power cable into an AC wall outlet, then use the control panel to adjust the height.
Figure 1: The controller is prohibited from
suspension testing to avoid false alarm.
Figure 2: The controller must be
fixed before testing.
Figure 1
Figure 2

7
CAUTION!
Failure to follow these instructions may result in property damage and/or personal injury.
Do not exceed desk weight limit. Keep area of vertical motion free of
obstacles.
Keep weight on desk balanced for
correct operation and longer life of
components.
Leave enough slack in cables to
allow for full range of vertical
motion.
PLEASE NOTE: The control unit has a gyroscope sensor and MUST be fixed to the desk for correct
operation.

LAST UPDATED: 03/11/2021
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303