Vivo STAND-V003E User manual

Triple Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003e
SKU: STAND-V003E
[email protected]om www.vivo-us.com 309-278-5303

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x3)
VESA Plate
C(x1)
Arm
D(x1)
Base
M-A (x12)
M4x12
M-D (x12)
M5x16
K (x3)
Screw
M-F (x12)
Spacer
M-E (x12)
D5 Washer
E(x1)
Pole
F(x1)
Pole
G (x1)
Pole
Connector
H(x2)
Cable Clip
I (x2)
Height
Adjustment Knob
J (x2)
Bolt
M-C (x12)
M5x12
M-B (x12)
M4x16
M (x1)
3mm Allen
Wrench
N (x1)
4mm Allen
Wrench
O (x1)
6mm Allen
Wrench
B(x1)
Bracket
L (x1)
Thumbscrew
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Slide one pole clip (H) on the pole (E). Add
one dual arm (C). Choose desired height and
tighten with Allen wrench (O).
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
E
D
K
N
Attach pole (E) into the bottom of the base (D). Use
the Allen wrench (N) to tighten the screws (K).
HC
E
O

4
STEP 3
Screw pole connector (G) to pole (E) and then add pole (F). Use Allen wrench (M) to tighten down the
grub screws on the pole connector.
STEP 4
Slide the single monitor bracket (B) onto the pole and secure at
desired height. Add another cable clip (H). Tighten with Allen
wrench (O).
E
G
F
M
B
H
O

5
STEP 5
Slide monitors onto all brackets.
STEP 6
OPTION A: Flat Back Monitor
For flat back monitor, install VESA plate (A) to monitor using bolts (M-A) or (M-C) and washers (M-E).
OPTION B: Curved Back Monitor
For curved back monitor, align spacers (M-F) with mounting holes in monitor and secure VESA plate
(A) to monitor using screws (M-B or M-D) and washers (M-E).
AM- A
M- C
M- E
AM- B
M- D
M- E
M- F

6
STEP 7
STEP 8
Route cables through cable management clips.
Add parts (J) and (I) to secure the monitors. Use the built-in adjustment screws on the brackets to align
your monitors. For the single bracket, add screw (L) to secure it.
J
I
1
O
2
L
3

7
STEP 9
Place Allen wrenches into slots on
clips for easy access.
STEP 10
Do not move monitors past center of gravity. This could result in tipping.
Adjust as Desired
N
O
+45 °
-45°
+45 °
-45°
+45 °
-45°
O
±180 °
±180 °
±180 °

LAST UPDATED: 10/28/2019
Open Monday-Friday from 7:00am-7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times.
If any parts are received damaged or defective, please contact us.
We are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]
www.vivo-us.com
309-278-5303
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
AVG. RESOLUTION TIME (within oice hrs): < 15 M