Vivo STAND-TV03N User manual

Black TV Floor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-tv03n
SKU: STAND-TV03N
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
T-A (x1)
Tool Kit
M4
Phillips
M4
Phillips
M2.5
B (x1)
Le Base
C(x1)
Right Base
A(x1)
Base
Connector
K (x2)
Plate Connector
and Plastic Shim
G(x2)
Front Rubber
Foot
D (x2)
Base Pole
E(x2)
Top Pole
F (x2)
Pole Connector
N (x4)
Pole
Cover
M (x2)
Shelf Support
J (x1)
VESA Bracket
Set
I x1)
Mounting
Plate
S-C (x4)
M4x12
M4x30
Screws
S-D (x4)
M6x20
M6x35
Screws
S-F (x4)
M4 Washer
S-G (x12)
M6 Washer
S-H (x4)
M8 Washer
S-J (x8)
M6/8 Spacer
(5mm)
S-E (x4)
M8x20
M8x35
M8x45
Screws
S-I (x4)
M4 Spacer
M6/8 Spacer
(20mm)
S-A x18)
M6x10
Screws
S-B x4)
M4x6
Screws
H x2)
Rear Support
Feet
L(x1)
Shelf
PACKAGE CONTENTS
T-B (x1)
Bubble
Level

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
Phillips
Screwdriver
Attach le and right base (B, C) to the base connector (A) using M6x10 bolts (S-A).
Tighten with the 4mm Allen wrench (T-A).
STEP 2
Install the Front Rubber Feet (G) onto the Right and Le Base (B,C). Install both Rear
Support Feet (H) onto the Base Connector (A) about three quarters of the way down.
Position them so they face backwards as shown below.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
110 lbs
(49.9 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 10 lbs
(4.54 kg)
CART SHELF
x1M4
M2.5
T-A
H
G
C
A
B
S-A
T-A
A
B
C

4
STEP 3
Thread the pole connectors (F)
onto the base poles (D), making
sure the connectors thread
in straight to avoid cross-
threading. Use caution when
threading pole connectors.
Threads are very fine and may
have sharp edges.
STEP 5
Thread the Top Poles (E) to the Pole Connectors
(F) and insert the Pole Covers (N) into the top.
Slide the Plate Connector and Plastic
Shims (K) over the Top Poles (E)
and tighten the set screw in each
connector using the 4mm Allen
wrench (T-A).
STEP 4
Attach the base poles (D) to the
assembled base using M6x10 bolts
(S-A) and 4mm Allen wrench (T-A).
x1M4
STEP 6
x1
M4
D
S-A
T-A
F
E
9
K
T-A
T-A
F
D
N
E
T-A

5
STEP 7
Attach the Mounting plate (I) to the Plate Connectors (K) with M6x10 bolts (S-A) and M6 washers (S-G)
using the 4mm Allen wrench (T-A).
Note: Loosly insert all bolts before fully tightening.
Clip the bubble level (T-B) onto the Mounting Plate (I). Adjust the level of the Mounting Plate (I) by
loosening the set screw in the back of the Plate Connector (K) using the 4mm Allen wrench (T-A).
Tighten set screws again once you’ve reached desired height and level.
STEP 8
x1M4
x1x1M4 Bubble Level
t
Attach bubble level
o the wal l plate
S-A
S-G
T-B
I
K
I
Attach bubble level to
Mounting Plate
T-A
T-A T-B
I
T-A

6
STEP 11
Tighten the safety bolts on the
bottom of the VESA brackets (J) to
secure the TV to the stand.
If the stand is not steady, adjust the Rubber Feet
(G) by tightening and loosening them. The Back
Support Feet (H) can also be adjusted but always
make sure that they are facing backwards.
STEP 12
Safety Bolt
STEP 9
Secure VESA Bracket Set (J) to the back of your television
using bolts (S-C through S-E) and washers (S-F through
S-H), depending on the size of the mounting holes on the
television. For curved or recessed TVs, Spacers (S-I, S-J)
may be required. Tighten using the Phillips end Wrench
(T-A).
Attach the VESA brackets (J) with
TV to the Mounting Plate (I).
STEP 10
S-I, S-J
(if necessary)
S-C through S-E
S-F through S-H
G
J
J
I
JH
x1
Phillips
T-A
x1
Phillips
T-A

7
STEP 13
For cable management, cables can be run through the top of the Pole Covers (N) and down through
the poles. Cables may also be inserted through the grommets in back of Base Pole (D).
OPTION A OPTION B
STEP 14
Attach the Shelf Supports (M) to the Base Poles
(D) using M6x10 bolts (S-A) and the 4mm Allen
wrench (T-A).
S-A
11
N
D
STEP 15
x1
Phillips
T-A
x1M4
T-A
Attach the Shelf (L) to the Shelf
Supports (M) using M4x6 bolts (S-B)
and tighten with the Phillips End
Wrench (T-A).
M
S-B
L
M

LAST UPDATED: 03/18/2021
REV2.1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303